Permatex® - Window Defogger Repair Kit - Quality Repair in Mins - 2.8ml #09117
Permatex
Window Defogger Repair Kit
2.8ml
#09117
PRODUCT DESCRIPTION
Permatex Window Defogger Repair Kit contains everything required for making professional-quality repairs in just minutes. Includes state-of-the-art components and easy-to-follow instructions with photographs. Provides a low-cost, high-quality repair for damaged rear window defogger grids and tabs.
Features:
Complete Kit contains everything required for making professional quality repairs in minutes.
Provides a low-cost, high quality repair for damaged rear window defogger grids and tabs
State-of-the-art components and easy to follow instructions with photographs
Premium repair kit for professionals and Do-it-yourselfers
Quick Grid is the result of a joint research project with the General Motors Research Center.
DIRECTIONS:
This
product will work only on tabs that have become detached from the side
grid of electric defogger. This product will not work on bare wires that
have
been
soldered to window grid and have been removed. Surfaces to be adhered
must be smooth and flat.
Read
all directions before beginning repair. Repairs can be made ideally at
temperatures from 50°F to 75°F (10°C to 24°C).
1.
Turn off the rear defogger. Carefully remove the tab from the wire
assembly.
2.
Ensure that the tab is flat and makes complete contact with the mounting
surface.
3.
Clean the lead attachment area on the rear window and tab with alcohol
towelette. (A) Note: DO NOT mount the tab on the same grid area if the
grid has
been
removed from the glass. There must be grid so that a complete circuit
can be made.
4.
If the grid has come off with the tab, rub the tab on a flat piece of
180 grit or finer sand paper until the surface is flat and of the same
color. (B)
5.
Grasp the corners of the Cleaner-Activator Towelette Packet (Part A) and
gently pull apart until green towelette is completely visible. DO NOT
REMOVE
TOWELETTE
FROM PROTECTIVE FOIL COVER. (C)
6.
Hold the Cleaner-Activator Towelette by the back of the protective foil
cover. (D) Wipe the grid area of the window where the tab is to be
attached and
wipe
the mounting surface of the tab itself. (E) Allow the activator to dry
for at least 2 minutes. (Tab must be attached within 15 minutes of
activation.)
DO
NOT TOUCH the grid mounting surface or the tab.
7.
Thoroughly knead the tab adhesive pouch until the adhesive is of a
uniform beige color. Do this by the placing pouch on a firm surface and
moving
adhesive
back and forth with fingernail. (F)
8.
Cut the top of the pouch. Apply one drop of adhesive to the surface of
the tab. (G)
9.
Immediately apply tab to rear window grid; hold firmly for 1 minute. (H)
Allow 24 hours to cure before turning on defogger. (I) If a multimeter
is
available,
check between tab and grid for continuity. There should be 0 ohms
resistance between the tab and grid. (J)
10.
Uncured adhesive around the tab may be cleaned off with alcohol.QUICK
GRID® REAR WINDOW DEFOGGER REPAIR
This
product is designed to repair scratched or broken rear window defogger
grid lines. Read all directions before beginning repair.
Repairs
can be made ideally at temperatures from 50°F to 75°F (10°C to 24°C).
1.
Determine which grid line(s) is/are broken and where the repairs need to
be made. Do this visually or use a multimeter.
2.
Turn off the rear defogger. Clean the surface of the glass with alcohol
towelette. (A)
3.
Remove the protective backing from the stencil provided. (B)
4.
Carefully place the stencil over the broken area of the grid. Make sure
to align both ends of the broken line with the stencil. (C)
5.
Make sure there is a good seal between the window and the stencil. Press
the stencil against the glass and make sure that all air bubbles are
removed.
6.
Shake the bottle of repair compound well. If solid material remains on
the bottom or sides of the bottle, it may become necessary to use a
toothpick
to
mix completely. (D)
7.
Using the small brush provided, apply the repair compound over the top
of the stencil. (E) Make sure that the repair compound overlaps with
both
ends
of the broken line.
8.
Wait for the surface to become tack free. Repeat the application
procedure three (3) times. Look through the window from the inside;
there should
be
no light showing through the repaired area. If light shows through,
apply another coat of repair compound.
9.
Remove the stencil after 30 minutes. (F) Wait 24 hours before turning on
the defogger. (G) (If a multimeter is available, check for resistance.
There
should be 0 ohms resistance on either side of the “fix”.) (H)
Permatex: Products designed for the DIY'er or the Industrial Professionals. Carrying a vast range of products designed for the Automotive and Engineering industry. Premium quality products, offer the best product at a very reasonable price. Permatex has been used around the world since 1909. Proven in Garages, Workshops, Racetracks and Service stations. Developed on Racetracks and dragstrips quality is continually tested to the Red Line, to ensure a constant performance over and over again. Vast range of products from Sealants, Threadlocks, Gasketmakers, and Epoxys, all of exceptional quality. View our ebay shop for the current range available. Items in stock and ready for immediate dispatch.
We are dedicated to ensuring the highest possible quality service to our customers.
Click to expand the tabs below to read more about our policies.