Store Categories
Details
Pattern Name: 1HZ-500KHZ
Used for alignment of audio equipment and up into the lower radio frequencies at the lower end of the Am band or Amateur bands
Small size, complete functions, simple operation, easy to carry.
It can be powered by adapter or lithium battery.
The good accuracy and frequency stability of DDS are suitable for oscilloscope scanning time factor calibration.
Square wave output, suitable for oscilloscope attenuator and probe pulse characteristic adjustment.
Together with the oscilloscope, it can be used for electronic circuit test and debugging, frequency characteristics and impulse response test and measurement of audio amplifiers.
1. Frequency range: sine wave 1Hz-500kHz (where the output amplitude is flat to 200 kHz, the output amplitude will decrease as the frequency is further increased), other waveforms 1Hz-50kHz (but the upper limit of the adjustable frequency is not limited, if The requirements for distortion and shaking are not high, and the frequency of use can be further increased).
2. Resolution: 1Hz.
3. Output waveform: sine wave, square wave, triangle wave, forward sawtooth wave, reverse sawtooth wave, electrocardiogram, noise wave.
4. Sine wave distortion: <1% below 1kHz, <0.5% above 1kHz.
5. Output amplitude: maximum ±10V (P-P).
6. Output impedance: 50 ohms.
7. DC offset: maximum ±10V, with shutdown function.
8. All setting parameters can be saved
9. There are filters that can be turned on and off, which can be well adapted to the output of sine and pulse waveforms.
10. Power supply: DC3.7-10V. It is recommended to use DC5V adapter, or 3.7V lithium battery.
11. Dimensions: 140x80x27 mm
1 x DDS Function Signal Generator
1 x USB to DC Power Cable
This is the description of Payment Method.
Do not dismiss your dream.
To be without dream is to be without hope.
To be without hope is to be without purpose.
Do not run through your life so fast that you forget not only where you have been, but also where you are
going.
Life is not race, but a journey to be savored each step of the way.
This is the description of Returns Policy.
Do not dismiss your dream.
To be without dream is to be without hope.
To be without hope is to be without purpose.
Do not run through your life so fast that you forget not only where you have been, but also where you are
going.
Life is not race, but a journey to be savored each step of the way.
Copyright©2017 DataCaciques
Details
Pattern Name: 1HZ-500KHZ
Used for alignment of audio equipment and up into the lower radio frequencies at the lower end of the Am band or Amateur bands
Small size, complete functions, simple operation, easy to carry.
It can be powered by adapter or lithium battery.
The good accuracy and frequency stability of DDS are suitable for oscilloscope scanning time factor calibration.
Square wave output, suitable for oscilloscope attenuator and probe pulse characteristic adjustment.
Together with the oscilloscope, it can be used for electronic circuit test and debugging, frequency characteristics and impulse response test and measurement of audio amplifiers.
1. Frequency range: sine wave 1Hz-500kHz (where the output amplitude is flat to 200 kHz, the output amplitude will decrease as the frequency is further increased), other waveforms 1Hz-50kHz (but the upper limit of the adjustable frequency is not limited, if The requirements for distortion and shaking are not high, and the frequency of use can be further increased).
2. Resolution: 1Hz.
3. Output waveform: sine wave, square wave, triangle wave, forward sawtooth wave, reverse sawtooth wave, electrocardiogram, noise wave.
4. Sine wave distortion: <1% below 1kHz, <0.5% above 1kHz.
5. Output amplitude: maximum ±10V (P-P).
6. Output impedance: 50 ohms.
7. DC offset: maximum ±10V, with shutdown function.
8. All setting parameters can be saved
9. There are filters that can be turned on and off, which can be well adapted to the output of sine and pulse waveforms.
10. Power supply: DC3.7-10V. It is recommended to use DC5V adapter, or 3.7V lithium battery.
11. Dimensions: 140x80x27 mm
1 x DDS Function Signal Generator
1 x USB to DC Power Cable
1.We only ship to the confirmed address provided by eBay. please make sure your ebay address is 100% matches the address you would like us to ship to. If not, please let us know before we sent you the package, or we will not be responsible for any loss. hope you could understand.
2.Orders will be processed instantly and dispatched within 1-2 business days except hoilday, so we do NOT accept any email/message note after you place orders.
3.All package need to wait 30 days,Please take care it.Less than 30 days,we can't take a refund.
1.We accept PayPal payment ONLY, and must be received within 5 days from the date of purchase.
2. It is easy and safe for you to pay by credit cards, debit cards, bank transfers and PayPal account balances.
3.Buyers are responsible for import duties,custom fees and taxes, if any, please check your country.
1.We believe our items are so outstanding. We are convinced you will be happy with your Purchase.
2. If you do not satisfy with our items. Please simply return to us within 30 Days in original condition. Just pay for the returned postage. Then we can issue full refund or resend the item to you after the returned item arrived at our warehouse.
3. Please include your eBay ID and item number with any email requests.