Name: Automatic screw counting machine
Model: FA-590A
Scope of application: up to 20MM
Applicable screw: 1-5MM
Output speed: 2PCS/S
Voltage: AC 110-220V
Size: 125*180*150MM
Net weight: 3.3KG
Capacity: M1-1500PCS/M2-1000PCS/M3-600PCS/M4-300PCS/M5-200PCS
Manual mode setting:
1. Select manual mode: In the off state, press and hold the B key, then press the power button to turn on the machine, display E000 (manual reset mode), then press the A key, switch to E001 (automatic reset mode), press the A key to cycle through the manual mode and automatic mode, finally press the F key to confirm saving and exit.
2. Fixed number setting: In the power-on state, long press the A button (hold down), it will start counting down, after the beep, release the A button, it will display d010 (the factory default setting is 10), press the A button to proceed To add processing, press the B key to perform subtraction processing. After setting properly, press the F key to confirm saving and exit.
Automatic mode setting:
1. Select the automatic mode: in the off state, press and hold the B key, then press the power button to turn on the machine, and it will display E001 (automatic reset mode). If it is not E001, you can press the A key to switch to E001. It is best to press the F key to confirm and save it. quit.
2. Delay setting: In the power-on state, long press the B button (press and hold), it will start counting down, after the buzzer, release the B button, display FF03 (factory default is 3 seconds delay), press A key to perform addition processing, and press B key to perform subtraction processing. After setting properly, press the F key to confirm saving and exit.
3. Fixed number setting: In the power-on state, long press the A button (press and hold), it will start counting down, after the beep, release the A button to display d010 (the factory default setting is 10), press the A button to increase Processing, press the B key to perform subtraction processing. After setting properly, it is best to press the F key to confirm saving and exit.
Model: FA-590A
Scope of application: up to 20MM
Applicable screw: 1-5MM
Output speed: 2PCS/S
Voltage: AC 110-220V
Size: 125*180*150MM
Net weight: 3.3KG
Capacity: M1-1500PCS/M2-1000PCS/M3-600PCS/M4-300PCS/M5-200PCS
Manual mode setting:
1. Select manual mode: In the off state, press and hold the B key, then press the power button to turn on the machine, display E000 (manual reset mode), then press the A key, switch to E001 (automatic reset mode), press the A key to cycle through the manual mode and automatic mode, finally press the F key to confirm saving and exit.
2. Fixed number setting: In the power-on state, long press the A button (hold down), it will start counting down, after the beep, release the A button, it will display d010 (the factory default setting is 10), press the A button to proceed To add processing, press the B key to perform subtraction processing. After setting properly, press the F key to confirm saving and exit.
Automatic mode setting:
1. Select the automatic mode: in the off state, press and hold the B key, then press the power button to turn on the machine, and it will display E001 (automatic reset mode). If it is not E001, you can press the A key to switch to E001. It is best to press the F key to confirm and save it. quit.
2. Delay setting: In the power-on state, long press the B button (press and hold), it will start counting down, after the buzzer, release the B button, display FF03 (factory default is 3 seconds delay), press A key to perform addition processing, and press B key to perform subtraction processing. After setting properly, press the F key to confirm saving and exit.
3. Fixed number setting: In the power-on state, long press the A button (press and hold), it will start counting down, after the beep, release the A button to display d010 (the factory default setting is 10), press the A button to increase Processing, press the B key to perform subtraction processing. After setting properly, it is best to press the F key to confirm saving and exit.
eBay Cross Border Trade powered by ChannelEffect