Store Categories

Battery Welding Machine Portable Mini DIY Spot Welder Machine 18650 Battery USB

Details

Features
1.9-speed power adjustable, five-level power display. Simple and convenient, powerful
2.5V charging, more convenient to use
3. Spot welder send nickel belt, one-handed, convenient to use
4. Charging display, buzzer alarm, more secure
5. Support 0.1~0.12mm thickness nickel piece, intelligent identification, automatic welding, simple and convenient operation
 
Specification
Maximum output current up to 1200A
Fully charged can continuously weld more than 1000 times
Five power levels can be adjusted, short press button control, blue light indication
Charging port: USB plug charging
Charging voltage: 5V input (higher voltage input is strictly prohibited)
Charging current: 1A (5V/2A charger recommended)
This product supports charging while using, the remaining power indication: green (high), green flash (high), red flash (low), red (low), the red light is on must be charged to work. Low power will affect the welding effect
 
Switching instructions
Short press to power on
Long press to shut down
6 minutes without any operation will automatically shut down
 
Note
Copper, aluminum surface can not be welded, rusty surface can not be welded, smooth stainless steel surface can be welded normally.
Part of the battery an electrode is stainless steel, an electrode is aluminum, our spot welder can weld stainless steel electrodes, aluminum electrodes need ultrasonic welding, please note.
Remind again, aluminum electrode, copper electrode can not be welded.
Common 18650, 32650 and other round batteries can be welded. The two needles are steadily pressed on the nickel piece before output welding, lift, and then weld next time.
 
Instructions for use
Spot welding nickel sheet
1. the battery should be fully charged, must be fully charged, spot welding nickel sheet, the thickness can not be thicker than 0.12MM.
2. spot welding attention to the pressure. The harder you press, the less heat; the lighter you press, the greater the heat; but too light will be perforated, too heavy and point not firm. So you need the right strength, do not press too hard.
3. the battery should be polished smooth, remove the surface of the oxide layer and uneven. Solder pen if oxidation black, please use fine sandpaper polished smooth. 4.
4. Use the most pointed point of the pen, so that you can also point firmly.
Welding method: Visualize the welding tip, and the horizontal plane into 60 ° grip, two needles at the same time pressed in the nickel surface pressure, good contact, current flow from one needle to the other needle, high current melting nickel, so that the battery and nickel welding success.
 
List
1 x Spot welder
1 x Nickel strip
1 x USB charging cable

 

This is the description of Payment Method. 

 

Do not dismiss your dream.

To be without dream is to be without hope.

To be without hope is to be without purpose.

Do not run through your life so fast that you forget not only where you have been, but also where you are 

going.

Life is not race, but a journey to be savored each step of the way.

This is the description of Returns Policy. 

Do not dismiss your dream.

To be without dream is to be without hope.

To be without hope is to be without purpose.

Do not run through your life so fast that you forget not only where you have been, but also where you are 

going.

Life is not race, but a journey to be savored each step of the way.

Copyright©2017 DataCaciques

Battery Welding Machine Portable Mini DIY Spot Welder Machine 18650 Battery USB

Details

Product Feature:
1.5 power adjustable, more precise welding with good results, fully charged, can continuously weld 1000 times
2. The spot welding machine comes with a nickel strip, which can be held by one hand and is convenient to use. It can weld mobile phone batteries and support the welding of various common nickel conversion mobile phone batteries. In addition, the portable feature makes it more convenient to repair mobile phones when going out
3. Supports nickel sheet welding with a thickness of 0.1-0.15mm, fully charged state supports 0.15mm nickel sheet welding, intelligent recognition, fully automatic welding operation, simple and convenient, supports stainless steel sheet and stainless iron sheet welding, with firm welding and excellent welding points
4. More precise welding, one hand operation, one hand grip, convenient operation and use, integrated advantage, can free one hand for holding nickel sheets or fixing batteries
5. Intelligent recognition, fully automatic welding, simple and convenient operation. This product supports charging while using. The remaining battery indicator is green (high), green flashing (medium high), red flashing (medium low), red (low). The red light must be charged before it can work.
 
Product parameters:
 
Battery voltage: 3.7V
Maximum output current up to 1200A
Fully charged, capable of continuously welding 1000 times
Five adjustable power levels, short press button control, blue light indication
Charging port: USB plug for charging
Charging voltage: 5V input (higher voltage input is strictly prohibited)
Charging current: 1A (it is recommended to use a 5V/2A charger)
This product supports charging while using. The remaining battery indicator is green (high), green flashing (medium high), red flashing (medium low), red (low), and the red light is on. Charging is necessary to operate. Low battery level will affect the welding effect
 
Switching on/off instructions:
Short press to power on
Long press to shut down
6 minutes without any action will automatically turn off
 
Note:
Copper and aluminum surfaces cannot be welded, rusted surfaces cannot be welded, and smooth stainless steel surfaces can be welded normally.
Some batteries have one electrode made of stainless steel and one electrode made of aluminum. Our spot welding machine can weld stainless steel electrodes, while aluminum electrodes require ultrasonic welding. Please note.
Reminder again, aluminum electrodes and copper electrodes cannot be welded.
Common circular batteries such as 1865032650 can be soldered. Two needles are stably pressed onto the nickel plate before welding can be output. Lift it up and weld again.
 
Instructions for use:
Spot welding nickel sheet
1. The battery should be fully charged and must be fully charged. The thickness of the nickel plate for spot welding should not be thicker than 0.15MM.
2. Pay attention to the pressure during spot welding. The harder you press, the smaller the heat; The lighter the pressure, the greater the heat; But if it's too light, it will puncture, and if it's too heavy, it won't hold. So it needs to be done with appropriate force and not too much pressure.
3. The battery should be polished and cleaned to remove the oxide layer and unevenness on the surface. If the soldering pen oxidizes and turns black, please polish it smooth with fine sandpaper.
4. Use the tip of the pen to point it firmly.
Welding method: Visually weld the head and hold it tightly at a 60 ° angle to the horizontal plane. The two needles are simultaneously pressed onto the surface of the nickel sheet, making good contact. The current flows from one needle to the other, and the high current melts the nickel sheet, thus successfully welding the battery and the nickel sheet.
 
Shipping list:
Spot welding machine X1
Nickel strip X1
USB charging

1.We only ship to the confirmed address provided by eBay. please make sure your ebay address is 100% matches the address you would like us to ship to. If not, please let us know before we sent you the package, or we will not be responsible for any loss. hope you could understand.

2.Orders will be processed instantly and dispatched within 1-2 business days except hoilday, so we do NOT accept any email/message note after you place orders.

3.All package need to wait 30 days,Please take care it.Less than 30 days,we can't take a refund.

1.We accept PayPal payment ONLY, and must be received within 5 days from the date of purchase.

2. It is easy and safe for you to pay by credit cards, debit cards, bank transfers and PayPal account balances.

3.Buyers are responsible for import duties,custom fees and taxes, if any, please check your country.

1.We believe our items are so outstanding. We are convinced you will be happy with your Purchase.

2. If you do not satisfy with our items. Please simply return to us within 30 Days in original condition. Just pay for the returned postage. Then we can issue full refund or resend the item to you after the returned item arrived at our warehouse.

3. Please include your eBay ID and item number with any email requests.

 

DataCaciques

On Nov 6, 2023 at 21:49:19 PST, seller added the following information:

DataCaciques