Description

 

WCH-LinkE-R0-1v3 Emulator MCU Programmer MCU Online Debugger for ARM Chips with SWD/JTAG Interface

Description:
WCH-Link (WCH-Link-R1-1v1)
The WCH-Link module can be used for online debugging and downloading of WCH RISC-V MCU, and also for online debugging and downloading for ARM MCU with SWD interface. Through its USB2.0 full-speed interface, it can be connected to a computer host. It is plug and play. Connected to target chips by the debugging interface, it can be used for debugging and programming.

WCH-LinkE (WCH-LinkE-R0-1v3)
The WCH-LinkE module can be used for online debugging and downloading of WCH RISC-V architecture MCU, and can also be used for online debugging and downloading for ARM chips with SWD/JTAG interface. A JTAG interface is provided to support four-wire connection (TMS line, TCK line, TDI line and TDO line) to extend the JTAG interface for a computer to operate CPU, DSP, FPGA, CPLD and other devices. Through its USB2.0 full-speed interface, it can be connected to a computer host. It is plug and play. Connected to target chips by the debugging interface, it can be used for debugging and programming.

WCH-DAPLink (WCH-DAPLink-R0-2v0)
The WCH-DAPLink module can be used for online debugging and downloading for ARM chips with SWD/JTAG interface. It supports two modes, i.e. ARM mode-WINUSB device and ARM mode-HID device. Through its USB2.0 full-speed interface, it can be connected to a computer host. It is plug and play. Connected to target chips by the debugging interface, it can be used for debugging and programming.

WCH-LinkW (WCH-LinkW-R0-1v1)
The WCH-LinkW module is a wired/wireless 2.4G dual imitation real debugger, which can be used for online debugging and downloading of WCH  RISC-V architecture MCU and also for online debugging and downloading for ARM chips with SWD/JTAG interface.

Features:
- Two 3.3V/5V power supply outputs are supported
- Supports USB to TTL serial port function
- Supports RISC-V chip single-wire/dual-wire downloading and debugging
- Supports downloading and debugging for ARM kernel MCU with SWD/JTAG interface
- Supports automatic firmware detection and upgrade
- 3.3V/5V output power supply is controllable
- Automatic power-off protection
- Red and blue LED indicator lights make it easy to check the working status
- Supports a host computer to switch working mode via one key

Specifications:
Default parameters of serial port:
- Data bit: 8
- Stop bit: 1
- Check digit: None
- Flow Control: None
- WCH-Link supports baud rates: 1200, 2400, 4800, 9600, 14400, 19200, 38400, 57600, 115200 and 230400bps
- WCH-LinkE/WCH-DAPLink/WCH-LinkW supports baud rates: 1200, 2400, 4800, 9600, 14400, 19200, 38400, 57600, 115200, 230400, 460800 and 921600bps

Product size:
- Size: 73 x 24 x 14mm/2.9 x 0.9 x 0.6"

Package Included:
- 1 x Programmer


Attention: Due to the differences in Flash programming of different target chips, this downloading speed is the result of target chip test of CH32F207, for reference only.




WCH-LINK:
- Supports WCH RISC-V architecture MCU and CORTEX-M core with SWD interface

WCH-LINKE:
- Supports WCH RISC-V architecture MCU and CORTEX-M core with SWD/JTAG interface

WCH-DAPLINK:
- Supports CORTEX-M core with SWD/JTAG interface

WCH-LINKW:
- Supports WCH RISC-V architecture MCU and CORTEX-M core with SWD/JTAG interface



Download/Upgrade Firmware:
WCH-Link Information:
https://www.wch.cn/products/WCH-Link.html

MounRiver Studio
http://www.mounriver.com

WCH-LinkUtility:
https://www.wch.cn/downloads/WCH-LinkUtility_ZIP.html

WCHISPStudio:
https://www.wch.cn/downloads/WCHISPTool_Setup_exe.html

WCHLinkEJtagUpdTool:
https://www.wch.cn/downloads/WCHLinkEJtagUpdTool_ZIP.html