Default Mode

The Default Setting:

1. Full spectrum white light in the day and blue in the night.
2. Full spectrum period: 06:30-18:30, blue light period: 18:00-23:30.
3. The brightness of the light changes in accordance with the curve designed.

Can Set：

1. Night colors can be changed, there are 6 kinds in total: dark blue, green, purple, cyan, yellow, red.
2. You can change the full spectrum white light period start and end time; night start and night time.

NOTE: No matter when the set time starts, the brightness of the light will gradually become brighter.

DIY Mode (suitable for plants tanks)

• 8 Time Stages: L1, L2, L3, L4, L5, L6 ---- All-optical; L7, L8 ---- Blue light;
• 10 Brightness: 10%, 20%, 30%, 40%, 50%, 60%, 70%, 80%, 90%, 100%;
• 8 Stage Setting Time: Any Time;

In each time stage can only set a brightness, and the start and end time of this time stage are set by yourself.

PS: No matter what time you set the end of the night, the lights will not turn off immediately, the fish tank light will turn off completely after 15 minutes. The brightness of the light for these 15 minutes is slowly dimmed until there is no. The purpose is not too scared your fish, not to suddenly turn off the light and not to suddenly turn on high brightness, which will give the fish a buffer stage.

Gradient Mode (Cycle Mode)

• Adjust the color of the light to dark red (after the yellow light), wait for about 20 seconds, and then begin to appear the color cycle - dark blue, green, purple, cyan, yellow, red.
• To turn off the DAY-L and MOON-L, it can continue to cycle, the next day's light color is also a cycle mode.

Brightness Change

There are 10 kinds of brightness can be adjusted, to simulate the effect of sunrise to sunset, and the brightness of the light can be set in different 8 Time Stages, which can realistically simulate natural light. Not only can it brighten the fish, it can also be applied to the growth of aquatic plants and promote photosynthesis.

Warm tips

The settings are wrong or the settings are confusing, you can restore the factory settings and start over. In the non-DIY mode, long press the up and down keys at the same time for a few seconds, until "SOP" appears, then unplug the power and plug again, it can restore the factory settings.

High efficient heat dissipation

The fin design increases the heat dissipation area, 0.05in thick aluminum. Note: why the aluminum surface of our hygger fish tank light appears heat.Because there is a heat dissipation sticker between the lamp bead and the aluminum material, there is no gap, and the heat is directly radiated to the outside, and the heat will not be stored in the light. The residual heat will damage the lamp beads, light decay, and even damage the power supply after a long time.

Suitable for many fish tanks

There are 6 sizes, and the extendable bracket, there is always a light that can be used for your fish tank. The use of a separable adapter will not cause the waste of replacing the LED light due to adapter damage. When there is a problem, if the display of the light can light up, it is not a power problem and the light needs to be replaced or repaired. If the screen flashes and then dims, or keeps dimming, it is a problem with the power supply, and you only need replace the adapter.

Rendering index 89

The irradiated light is softer and does not hurt the eyes, the light is more stable. If you use a mobile phone to take pictures,the screen is not flashing, the eyes and the fish are protected. The spectrum is smooth, close to the sunlight, the light is more natural. 5 rows of lamp beads, the light surface is wider, the color is bright. High lumens, translucent fish tanks, and brighter plants.

Waterproof grade IP68

Waterproof grade IP68, fully sealed and waterproof, high light transmittance, waterproof and easy to clean. Long-term use does not decay, the light effect is pure and transparent, the life is long, and it can be used for tens of thousands of hours.