The LiitoKala Lii-S8 universal charger is a multi-functional eight-channel charger with easy-to-use controls, an informative LCD display that displays capacity, internal resistance, and charge percentage. Automatically recognizes lithium-ion, nickel-metal hydride and nickel-cadmium batteries, charges lithium-phosphate (LiFePO4) batteries and can simultaneously charge from 1 to 8 (current up to 2 A 4 batteries) cylindrical batteries of different chemical composition and almost all sizes of AA batteries , AAA, C (R14), A, SC, 14500, 16340, 18350, 18650, 21700, 20700, 26650 and others.

Distinctive features and advantages of Lii-S8: — charges batteries in 8 independent channels; — has an informative LCD display with a yellow backlight; — the function of determining the internal resistance of batteries in mΩ. — charges Li-Ion (Li-Ion 4.35 V), LiFePO4, NiCd, NiMH. — installation of batteries up to 72 mm long; — the ability to quickly charge with a current of 2 A in 4 slots (1, 3, 6, 8); — allows simultaneous charging of 21700, 26650, 18650 batteries; — the ability to be powered directly from the network or 12 V (12V/4A power supply unit included). It is possible to connect via an adapter to the car; — activation of fully discharged batteries; — detection of defective batteries. The LiitoKala Lii-S8 charger is simple, intuitive to use, with which you do not need to buy several chargers — you can charge different form factors of batteries and different chemical compositions with one charger. All ports of the LiitoKala Lii-S8 charger are independent and individually controlled, which makes it possible to charge batteries of different types and chemical compositions at the same time. The presence of a clear LED indication makes it easier to work with the LiitoKala Lii-S8. The charger automatically recognizes Ni-MH, Ni-Cd, Li-ion, LiFePO4 batteries and can charge them with different current, it is selected automatically depending on the number of installed batteries, and the voltage is selected separately depending on the type of battery. Each slot automatically turns off when the maximum charge level is reached. Variants of charge currents. For Li-ion/LiFePO4: 300-1000 mA — 1-8 batteries. 2000 mA — 4 batteries. For NiMH/NiCd: 500 — 1-8 batteries. Crown NiMH/NiCd 9V 85 mA — 2 batteries. Selection of charge current: 300mA / 500mA / 700mA / 1000mA / 2000mA The movable spring-loaded contact adjusts to the length of the battery, allows you to charge almost any size of batteries, starting from the compact 14500 and ending with the large 21700 and 26650.

During charging, the following information is displayed on the LCD display: • set mode of operation • charge current (mA) • battery voltage (V) • accumulated or real capacity (mAh) • internal resistance (MOhm) • charging time (h) • percentage of battery charge (%) • channel number, information about which is displayed (CH*) Charging and management process: Battery charging mode. Install the battery, observing the polarity, into one of the 8 slots. During 3 sec. the voltage, internal resistance, charge percentage and temperature of the battery will be determined, then you will be asked to select the charge current. CURRENT button — short press this button to select the charge current of 300-500-700-1000 or 2000mA. If no selection has been made within 8 seconds, the charge with a current of 1000mA is switched on. MODE button - with this button you can select the type of chemistry of the rechargeable cell Li-Ion (Li-Ion 4.35V), LiFePO4, NiCd/NiMH. You can switch between channels using the SCAN/PREVIOUS buttons, which correspond to the NEXT/PREV buttons. After charging, the display will show that the battery has a charge level of 100%. The charge of battery crowns is 9 V. To use the charging function of the 9V battery crowns, simply install the crown nickel-metal hydride battery NiMH/NiCd observing the polarity in one of the two channels that are located on the left at the top of the charger, then you will see that the LED has changed from green to red, after finishing of charge, the LED that corresponds to the channel in which the crown is installed will light up green. Technical characteristics of the Lii-S8 — 8 independent charging channels for Li-Ion, LiFePO4, Ni-MH and NiCd batteries. — High-quality, informative LCD display. — The function of determining the internal resistance of batteries in mΩ. — Display of battery charge level by % ratio. — 8 separate indicators for each charging channel reflect the state of charge of each slot independently of each other. — Wide range of charging current selection: 300mA / 500mA / 700mA / 1000mA / 2000mA — Discharge function to reduce the memory effect. – Built-in protection circuit against overcharging, short circuit. — The function of determining the capacity and eliminating the memory effect. – Output voltage: 4.2/ 4.35/3.65/1.48 V (selected automatically depending on the type of battery installed). — Determination of the full charge of Li-ion (4.2V), LiFePO4 (3.65V), Ni-Cd/Ni-MH (1.48V) batteries by voltage. — Activation of fully discharged batteries. Input power: DC 12V 4A. Operating temperature: 0 - 40°C. Dimensions: 195*142*35 mm. Weight: 300g. Delivery set: - charger; — power supply unit 12V 4A; — car adapter; — instructions in English; - packaging. WARNING! Batteries cannot be charged if the correct polarity is not observed and the battery poles are not in good contact with the contacts of the charger. Before using the charger, check that the accumulators/batteries are compatible with the charger! Do not attempt to charge Li-polymer batteries with this charger, as this is dangerous and may cause both the batteries and the charger to fail! Do not use the charger in conditions of high humidity and temperature!