For 3000W Hybrid Controller

Product introduction:
This kind of wind solar hybrid street light controller is a special design for small off-grid devices where wind generators and solar panels charge batteries safely and efficiently.

Functions:
** Wind generator MPPT boost charging function.
** Wind PWM dump load, external dump load resistor, intelligent solar charge separation.
** Dual power supply function: battery + solar power supply.
** LCD displays parameters such as voltage and current of wind, sun and load. Some parameters can be set by the user.
** DC output with 3 output modes.
** The inner circuit board of the controller is sprayed with protective paint to prevent dust, moisture and static electricity.

Features:
** Wind & Solar MPPT charging method, ensure the power get max input into the battery and high charging efficiency.
** Can be used for 3000W wind turbines with high compatibility.
** Independent Boost Circuit: The charging efficiency of the low-power vertical wind generator has been solved.
** 12V/24V (12V/24V/48V) system auto-detect function.
** Mini size, easy to install.
** LCD display with visible and intuitive parameters.
** Rated wind power: 100-1000W
** PV Rated Power: 100-2000W

Package list:
1 * Wind&Solar hybrid charge controller with dumpload

Thank you for purchasing our products. This manual is intended for people who need to install and operate the controller. Read this manual before doing any work on the controller and keep it in a safe place. The content of this manual is regularly updated or revised as necessary. However, deviations cannot be ruled out. Please refer to the actual product(s).

General Safety Information:
** Before you receive the product, please check it carefully. Make sure the product has not been damaged in transit. If it is damaged, contact the carrier or our company immediately.
** All installation and electrical work may only be carried out by qualified personnel.
** Do not disassemble or attempt to repair the controller without professional guidance.
** Do not use the controller without batteries.
** Do not disconnect the controller and batteries when the controller works normally.
** Keep children away from the controls.
** Do not allow water to get into the controller.
** Ensure power connections are tight to avoid excessive heating from a loose connection. Make sure the cables are appropriate for the system.

For 3000W Wind Turbine:

Specification
Condition: New
Control system: Electromagnetism
Starting wind speed: 1.3m(12inch)/s
Switched on wind speed: 2.5m(98inch)/s
Rated wind speed: 11m(433inch)/s
The instantaneous maximum wind speed: ≤45m(1772inch)/s
Blades quantity: 3
Diameter of the blades: 0.6m/24inch
Height of the blades: 0.8m/31inch
Speed regulation: Automatic
Rated voltage: 12V/24V/48V (for your choice)
Rated power: 2500W
Max power: 3000W
Protection class of the generator: IP67
Working environment temperature: 25 to 45℃+
Product assembly weight: 10kg
Protection against overspeed: Electromagnetic brake
Blade material: glass fibre
Generator: Magnetic levitation generator
Useful life: 10-15 years
Installation instructions: Not included in the scope of delivery

Description
The wind turbine with the coreless permanent magnet generator and three high-strength nylon fiber blades is more durable and has a long service life. The spiral blades are aerodynamically designed to make the rotor run smoothly and reliably, which leads to stable electricity generation. Besides, it has maximum speed protection. It is well suited for boats, gazebos, cabins or mobile houses, and other energy supplies for homes, businesses and industry.

note：The wind speed needs to reach 18m/s for the machine to generate electricity properly.

Installation
1. Check all the parts of the wind turbine, which includes 6 brackets and 3 blades in total.
2. Place the wind turbine vertically.
3. Connect brackets with blades by the bolt. Load the upper cover plate and lower cover plate.
4. Fix the bolt in the mounting hole (at the end of the bracket) from the outside of the wind blade.
5. Tighten all the bolts of blades and brackets, and toggle the blades. It should not have abnormal noise or jamming. Tighten the nut (under the upper cover plate of the wind turbine) to make the upper cover plate tightly fixed.
6. Align the flange hole of the wind turbine with the flange hole on the tower pole, put on flat washers and spring washers, and tighten the nut.
7. Professional installation is highly recommended if you have no previous installation experience.
8. You can watch the attached installation video as a reference.
9. If you have any problems, please feel free to contact us. We will reply and solve the problem for you as soon as possible.

Key Features

Great Durability: The wind turbine with the coreless permanent magnet generator and three high-strength nylon fiber blades is more durable and has a long service life.
Smooth Running: The spiral blades are aerodynamically designed to make the rotor run smoothly and reliably, which leads to stable electricity generation. The double bearing and low vibration also ensure more stable operation.
Low Noise: Drawing on the design principle of aircraft wings and the horizontal plane rotation, noise can be reduced to a level that cannot be measured in the natural environment.
Generating Electricity at Lower Wind Speeds: Due to its compact shape, low starting wind speed, and large windward area, the wind turbine can generate electricity at lower wind speeds.
Strong Wind Resistance: The horizontal rotation brings small wind pressure so that it can resist a super typhoon.
Maximum Speed Protection: When the wind turbine reaches the maximum speed of 300rpm, it will automatically brake.
Easy to Install: Everything you need for installation is included. The wind turbine with a user-friendly and convenient flange design is easy to install.
Low Starting Wind Speed: Its starting wind speed is lower than other wind turbines, and the rising arc of power generation is gentle, so it can generate more power than others within a certain range.

Package Included
1 x Wind Turbine
1 x Controller
3 x Blades (White, Red, Blue)
1 x Bag of Screws to Connect the Main Body
1 x Bag of Screws for Connecting the Bracket Blades
Other Accessory for Assembly

For 2000W Power Inverter

Specifications:
Type: Pure Sine Wave Inverter
Output Voltage Waveform: Pure sine wave
Power: 2000W Peak / 800W Continuous
Output voltage: 220V
Input voltage: 12V/24V/48V
Output frequency: 50Hz
Socket: Universal

In the Box:
1 x Pure Sine Wave Inverter
1 x User manual
Peak power 2000W
Continuous power 800W
Weight: 2 kg

Features:
- Aluminum-magnesium alloy shell, light weight, good thermal conductivity.
- Digital Battery Volts Display
- Pure sine wave, intelligent filter, does not interfere with electrical appliances, protects electrical appliances. With high conversion efficiency (up to 95%), the low power consumption of the product can greatly extend battery life.
- You can use electrical equipment, including TV / LED lights / LCD displays, especially inductive load appliances such as refrigerators, freezers, induction cookers.
- Pure sine wave inverter.
- 8-bit intelligent protection: overload protection, high voltage protection, low voltage protection, overheating protection, reverse connection protection, short circuit protection, overcurrent protection, surge protection, intelligent chip control.
- Intelligent temperature control fan means the inverter is quiet. When the temperature is ≤45 ℃, the fan is not spinning; when the temperature is ≥45 ℃, the fan starts working.
- Buzzer reminder. Once any protection of the inverter is triggered, the inverter will immediately disconnect, the inverter enters the protection mode, with a buzzer reminder.