" Genuine" Gunson G4062 Eezi Bleed Brake Clutch Bleeding Tool Kit
Item Description

This system sets the standard for affordable brake and clutch bleeding systems. Using air pressure from a spare wheel it will effortlessly bleed hydraulic systems. There are a number of adaptors available to fit most vehicles with screw cap reservoirs, and comprehensive instructions are included.


Additional Information

  • Suitable for one man operation
  • Uses the air pressure from a spare tyre to effortless bleed hydraulic systems
  • The Eezibleed kits contains a special pressure vessel to hold the new fluid, spare bottle seal part number G4062/80
  • Can be used successfully on the following systems: Tandem master cylinders without sensors Tandem reservoirs, Slave servos, Vacuum Servos
  • Easy to follow instructions
Further Hints and Tips:
Some cars' brake systems are very difficult to bleed; a pressure bleeder such as this
invariably gives better results than a non-pressure method such as the conventional two
person method, and most vehicle manufacturers recommend pressure bleeding for both
brake and clutch hydraulic systems.
1. Make sure that the cylinders on all four wheels are bled.
2. Always use new brake fluid and do not re-use any brake fluid that has passed through
the system.
3. If the pressure bleeding alone does not work (i.e. the brake pedal remains 'spongy'),
try pressing the brake pedal while the pressure bleeding is in operation (i.e. carry out
pressure bleeding and conventional bleeding simultaneously).
4. Try bleeding the brakes while the car is tilted either forwards or backwards.
5. If the master cylinder has been removed or dismantled for any reason it may, in the
case of certain cars (particularly early Minis and the Jensen Interceptor) be very difficult
to bleed the brakes satisfactorily. In this case it is necessary to bleed the master
cylinder on its own, before fitting the pipes to it. Ensure that it is completely filled with
fluid before connecting it to the rest of the brake system.
6. If any component of the brake system (such as the master cylinder) has been
dismantled, it will be necessary to consider the possibility that the parts have been
incorrectly re-assembled or incorrect components have been fitted. Dismantle the part
and start again.
7. The recommended setting of pressure for the device (20 psi) is intended purely as
a guide. In some cases a lower pressure will give adequate flow, possibly as low as
10 psi for older (classic) vehicles. In some vehicles, a higher pressure (over 10 psi) is
better for bleeding the brakes of the rear wheels.
8. The device will not fit the reservoirs of some cars and indeed, some manufacturers
have been known to fit different types of reservoir to the same model of car. It will
not fit Nissan, Honda and some Toyotas. There are several ways of overcoming
this problem. One way is the multipurpose cap 77042 (not included but available
separately), which is held to the reservoir by means of a strap which passes beneath
the reservoir. Another method is to buy a spare cap and drill a 10mm hole in it. Where
the cap has a removable centre it is possible in some cases, to make a disc with a
10mm hole and temporarily fit this to the car's normal reservoir cap. If this method is
used it is vitally important to pressure-test the system without fluid in the Eezibleed
bottle.
9. When finished, always clean the pressure vessel bottle (A), the bottle cap assembly
(B) and the bleed valve hose (C) with brake cleaning fluid or similar (old brake fluid will
attack the rubber seals). Then dry off and store in a dry place.


Spare Parts Available:
Component Part Number Component Part Number
Bottle Cap: G4062/02 Bottle Cap seal: G4062/80
25mm Cap: G4062/07 25mm Cap seal: G4062/44
28mm Cap: G4062/11 28mm Cap seal: G4062/46
46mm Cap: G4062/15 46mm Cap seal: G4062/50
44/45mm Cap: G4062/21 44/45mm Cap seal: G4062/22 (3mm)
44/45mm Cap seal: G4062/23 (1.5mm)

Order Payments 

Payment methods : Cash on collection,Paypal,Debit / Credit Card over the telephone 

About Us 

Repairing vehicles is our business with 50+ years experience we feel well accomplished to trade within the automotive sector as a supplier of tools & garage equipment. Most suppliers of automotive equipment & tools do just that and only that.,This is where our business has the advantage over our competitors.
We carry large stocks for immediate supply, Having our own up to date vehicle workshop and bodyshop we have a wealth of experience & skill to advise on any questions we are asked from technical data to how an item may work.

Shipping

We dispatch items within 24/48 working hours of the order being processed. We keep all our stock levels as accurate as possible but as we sell on multiple platforms sometimes there may be errors that lead us to not having stock of your item, if this happens we will work with you to resolve this as quickly as possible
We use Royal Mail for most packages under 10kg for the UK  dependant on size, All UK parcels have full door to door tracking , 
We have a choice of courier services that we can use upto 150kg Normal UK Delivery is 2-3 working day delivery after dispatch

Returns

To request an item return:
1. Go to My eBay. You may be asked to sign in. 2. Click Won. 3. Next to your listing, select Return this item from the pull-down menu. 4. Select "I want to return an item" and click Continue. 5. The "Return an item" form appears. 6. Review the next page and click Request return. 7. Then you have to wait for seller to accept your return request. 8. After the seller has accepted your request, you can prepare postage right away and click Continue. 9. Post the item to the seller.
Shop By Brand
Powered by Frooition
This listing is currently undergoing maintenance, we apologise for any inconvenience caused.