User manual
1. Characteristics and Range of application:
The
DIN rail single phase electronic energy meter is a kind of new style
single phase whole electronic type meter, and adopt up to date
micro-electronics technique and imported special large scale integrate
circuit, use advanced technique of digital sampling technique and SMT
technics etc.
The meters are completely
conformed to the relative requirements of the National Standard
GB/T17215.321-2008 and International Standard IEC62053-21 on the meter
(Class 1).
The meter is used for
measuring active energy power consumption in a rated frequency of 50Hz
or 60Hz . It can accurately and directly measure active energy
consumption from positive and reverse directions. It has following
features: Good reliability, small volume, light weight, specious nice
appearance, advanced technics.
The meter
is installed indoors. The site conditions shall be assumed as follows:
The ambient temperature is -25 ~ +55℃, relative humidity is not more
than 95%. There isn’t heavy corrosive gas or any influence of dust, mold
and insects etc.
2. Installation and usage:
2.1
The meter can be installed and used after being test and sealed.
Without sealed or storage time is too long the meter must be retesting.
2.2
When take out the meters from original packing, if the inner packing or
meter cover is found broken, then do not install the meter, please
contact company technical service dept.
2.3 Only experienced electrician or professional technician can install the meter, and confirm to read through the User Manual.
2.4
The meter must be installed ventilate and arid place, the meter base
board must be on the wall of fire resistance and uneasily shaking.
2.5 The meter must be installed in the protective box in the dusty place or against possible mechanical damage.
2.6
Connecting must accord with meter case body connecting or the
connecting drawing of the Usage Manual. Commend to use soft brass wires
to input to avoid that the meter shall be burnt due to loose contact.
2.7 When the meter is connected in the electricity net rightly, the meter power indication light should be bright up.
2.8 In the too much thunderstorm place to adopt measures to avoid the lighting damage.
2.9
The load capacity of the meter is between 0.05Ib~Imax. If the capacity
exceeds above the register shall not be accurate or the current coil
shall be heated and burnt.
2.10 Data display:the
meter have two rows of display,the first row shows electricity is can be
cleared,press the “RESET”button on the front panel 3~5 seconds is can
to zero,second row shows total electricity is do not reset.
2.11
Impulse indication: When connecting meter load using energy, the
impulse indicator light twinkle display (Lighting about 80ms).
3. Outer and connection drawing:
3.1 Outer drawing![#ff0000](https://cbu01.alicdn.com/img/ibank/2018/126/205/8663502621_902426047.jpg)
3.2 Connection drawing
![#ff0000](https://cbu01.alicdn.com/img/ibank/2018/445/135/8683531544_902426047.jpg)
| Terminal | Note |
1 | Inputphase line |
4 | Neutral line |
2 | Outgoing phase line |
3 | Neutral line |
4. Test mode:
The meter has energy impulse output port, it locates in terminal 23 and terminal 24.
5. Transport and storage:
4.1 Transport and storage of the meter must not be shaken and must accord with ZBY002-81.
4.2
The meter must be stored in the original packing box and the
environmental temperature is in -35℃~+65℃. Relative humidity shall not
exceed 95%. And there isn’t any corrosive gas. The environmental
temperature shall not vary violently.
4.3
The meters should be in the original packing box and the boxes should
be piled up no more than five on the rack. The separate meter is not
suitable for storage.
6. Deadline of guarantee:
Within
18 months from the date of manufacture the user complies with all of
above rules. If the meter still being sealed does not conform to any
technical requirements of IEC62053-21 & GB/T17215.321-2008,
or
of any certification of Power Department or Measuring Department,the
manufacturer guarantees to repair freely or to replace it.