Description
USB Linear CCD Array High Resolution TCD1304 Integration Time Adjustable 1ms-100ms
Features:
- AD sampling rate: 125kHz.
- AD sampling depth: 16Bit.
- USB 2.0 interface with chip FT245. The maximum communications rate is 1MByte.
- CCD driving and data sampling control circuit is completed by branded components.
- CCD chip: Branded TCD1304AP. Pixel size is 8um x 200um, a total of 3648 pixels, wavelength response range is 300nm ~ 1100nm.
- CCD's integral exposure time is adjustable in 1ms-100ms or 10us-10S, the former is adjustable in 100 steps and the latter is continuously adjustable.
- Trigger mode is optional for internal or external trigger software programming.
- The CCD sampling speed set during internal triggering is 10 frames / second for 1ms-100ms integration time. If the integration time is greater than 100ms, the sampling rate will decrease accordingly.
- The trigger frequency of external trigger can be set to any frequency between 1Hz and 20Hz as required, and a single trigger is also available.
- CCD image data can be input to a computer via USB. It can also be displayed by an oscilloscope or collected via other acquisition cards via a synchronous analog output port.
- The synchronous trigger output port can output the internal clock signal or external trigger signal during internal trigger synchronously. This signal can be used to trigger an oscilloscope, which is synchronized with the analog signal of the CCD image.
- The test software is written for Borland C ++ Builder, and the source code is sent to the customer along with the CCD board.
- In addition to source code routines for BCB, source code routines for Visual C ++ (1ms-100ms integration time) are included. Users can modify and make their own software on it. If users need to write with other software for VB, Delphi or Labview, they can log in to the official website of FT245 supplier www.ftdichip.com/Support/SoftwareExamples/CodeExamples.htm to download the corresponding routines. Customers can embed CCD data acquisition, CCD integration time, and internal and external trigger commands in the corresponding routines, that is, they can control the CCD based on the software written by them.
- The model of this linear array CCD (TCD1304) is the same as the ones used in HR4000 spectrum, and the driving circuit is basically similar, so customers can use this CCD to develop a spectrometer.
- The external trigger function of this CCD can be used to catch low frequency or even single laser pulses.
- Scan with this linear array CCD to measure images with larger diameter spots (> 2cm).
- The drive circuit board and the CCD sensor can be installed separately. The two are connected by a cable. The cable length is 5cm ~ 1m.
- It has been successfully applied to a spectrometer, and has measured the laser spectrum of a sub-10fs titanium sapphire femtosecond laser, as shown in the picture above.
- The sensitivity of this linear array CCD is extremely high, so it can measure very weak lasers. Of course, users must also attenuate the laser sufficiently before entering the CCD photosensitive surface, otherwise the CCD will be saturated or its photosensitive unit will be burned out.
Package Included:
- 1 x Set of USB Linear CCD
Features:
- AD sampling rate: 125kHz.
- AD sampling depth: 16Bit.
- USB 2.0 interface with chip FT245. The maximum communications rate is 1MByte.
- CCD driving and data sampling control circuit is completed by branded components.
- CCD chip: Branded TCD1304AP. Pixel size is 8um x 200um, a total of 3648 pixels, wavelength response range is 300nm ~ 1100nm.
- CCD's integral exposure time is adjustable in 1ms-100ms or 10us-10S, the former is adjustable in 100 steps and the latter is continuously adjustable.
- Trigger mode is optional for internal or external trigger software programming.
- The CCD sampling speed set during internal triggering is 10 frames / second for 1ms-100ms integration time. If the integration time is greater than 100ms, the sampling rate will decrease accordingly.
- The trigger frequency of external trigger can be set to any frequency between 1Hz and 20Hz as required, and a single trigger is also available.
- CCD image data can be input to a computer via USB. It can also be displayed by an oscilloscope or collected via other acquisition cards via a synchronous analog output port.
- The synchronous trigger output port can output the internal clock signal or external trigger signal during internal trigger synchronously. This signal can be used to trigger an oscilloscope, which is synchronized with the analog signal of the CCD image.
- The test software is written for Borland C ++ Builder, and the source code is sent to the customer along with the CCD board.
- In addition to source code routines for BCB, source code routines for Visual C ++ (1ms-100ms integration time) are included. Users can modify and make their own software on it. If users need to write with other software for VB, Delphi or Labview, they can log in to the official website of FT245 supplier www.ftdichip.com/Support/SoftwareExamples/CodeExamples.htm to download the corresponding routines. Customers can embed CCD data acquisition, CCD integration time, and internal and external trigger commands in the corresponding routines, that is, they can control the CCD based on the software written by them.
- The model of this linear array CCD (TCD1304) is the same as the ones used in HR4000 spectrum, and the driving circuit is basically similar, so customers can use this CCD to develop a spectrometer.
- The external trigger function of this CCD can be used to catch low frequency or even single laser pulses.
- Scan with this linear array CCD to measure images with larger diameter spots (> 2cm).
- The drive circuit board and the CCD sensor can be installed separately. The two are connected by a cable. The cable length is 5cm ~ 1m.
- It has been successfully applied to a spectrometer, and has measured the laser spectrum of a sub-10fs titanium sapphire femtosecond laser, as shown in the picture above.
- The sensitivity of this linear array CCD is extremely high, so it can measure very weak lasers. Of course, users must also attenuate the laser sufficiently before entering the CCD photosensitive surface, otherwise the CCD will be saturated or its photosensitive unit will be burned out.
Package Included:
- 1 x Set of USB Linear CCD
Payment Terms
1.We accept PayPal only.
2.All major credit cards are accepted through secure payment processor PayPal.
3.Payment must be received within 7 business days of auction closing.
4.We ship to your eBay or Paypal address. Please make sure your eBay and Paypal address is correct before you pay.
2.All major credit cards are accepted through secure payment processor PayPal.
3.Payment must be received within 7 business days of auction closing.
4.We ship to your eBay or Paypal address. Please make sure your eBay and Paypal address is correct before you pay.
Shipping Terms
- For remote regions, we will charge your extra shipping costs. Usually it cost about 35USD-50USD. We will contact you after your payment. Thanks for your understanding.
Return Terms
1. If you receive defective item, please kindly notify us within 14 days. We will guide you the returning instruction for replacement or refund.
2. If you purchased in improper condition, please NOTE that the sipping and handling fee will not be refund, all return shipping fee should paid by the buyer unless item DOA.
3. We reserve the right to refuse any returns for objective reasons.
2. If you purchased in improper condition, please NOTE that the sipping and handling fee will not be refund, all return shipping fee should paid by the buyer unless item DOA.
3. We reserve the right to refuse any returns for objective reasons.
Custom Duties & Taxes
1. Import duties, taxes, and charges are not included in the item price or postage cost. These charges are the buyer's responsibility.
2. Avoiding some unnecessary trouble, please check with your country's customs office to inform us what we should declare its value before shipping.
2. Avoiding some unnecessary trouble, please check with your country's customs office to inform us what we should declare its value before shipping.
Feedback
1. If you are dissatisfied for any reason, please don't be quick to leave us neutral or negative feedback. We work hard to make sure EVERY CUSTOMER 100% SATISFIED and resolve any problem for you and always leave positive feedback to all our customers.
2. If you are satisfied with the product you received, please kindly leave us a positive feedback and 5 star DSR. If there is any problem of your order, please feel free to contact us firstly, we are responsible and credible seller, will follow it for you asap.
2. If you are satisfied with the product you received, please kindly leave us a positive feedback and 5 star DSR. If there is any problem of your order, please feel free to contact us firstly, we are responsible and credible seller, will follow it for you asap.
On Jul-28-20 at 19:00:58 PDT, seller added the following information: