You can switch / combine the two effect loops.
Noise is also reduced by the class A buffer circuit.
With the DRAG control, you can reproduce the tone and touch as if you connected an amplifier directly.
Made in Canada
It is a domestic regular import product. It comes with a warranty card that is valid for one year from the date of purchase. You can still get support from an authorized dealer even after the free warranty period has expired.
Equipped with 2 effect loops
Equipped with two independent effect loops,
Effects for solo and effects for rhythm
(For basic sounds, special effects, etc.)
Prepare two types of effects,
You can control many effects with less switching.
Since the loop is independent of the main line,
Vintage effects, etc.
Even effects with a lot of noise and severe deterioration of sound quality
It can be incorporated into the system without any problems.
Solve the problem of increased pedals
Many guitar players, from vintage to the latest models,
Create your own tone by making full use of countless pedals.
Some pedals can be a noise source just by connecting them.
Some of them have severe deterioration in sound quality, which is a big problem in the field.
As the effect increases,
It also makes it difficult to operate the foot switchg.
It solves the problems of using such a large number of effects.
Loopbone should be the center of the pedal board
With functions that have various functions and realize various sounds
It has excellent sound quality.
Outstanding sound quality
By degrading the guitar signal or using an effects loop,
The buffer is carried so that the sound quality does not change.
The buffer has the effect of lowering the impedance,
Even when using a long cable, it is less susceptible to noise.
Lighting equipment that is often a source of noise
It is extremely effective on large-scale stages around the area.
If the quality of the buffer is inadequate, the sound quality will be sacrificed.
IC and many effect pedals
A buffer using an operational amplifier is installed.
ICs and operational amplifiers are low cost and small in size,
The sound is not good.
The buffer installed in Loopbone is
Discrete class A circuit with good sound.
Therefore, sound quality is not sacrificed.
Gain booster
After the effect loop
The class A gain booster (up to 15dB) is carried.
Since it is after the loop, the effect sound is left as it is
It can be boosted cleanly.
Ideal when you want to raise the volume such as a guitar solo.
Reproduce the sound with the amplifier directly connected
Generally when you connect your guitar directly to your amp
Guitar pickup and amplifier input,
Also, the sound will change due to resistance from the cable.
That change is one of the reasons why each amp has its own unique sound.
However, if there is a buffer in the meantime
The guitar-amp correlation is lost.
Loopbone is equipped with a buffer to eliminate noise.
Normally, once the guitar signal is active,
The sound will be different than when you connect it directly to the amp.
However, Loopbone has a Drag control.
The Drag control reproduces the sound directly connected to the amp.
This control revives the unique correlation between the guitar and the amp.
Even if you build a loop system, you can get a natural sound.
Independent tuner out
Most tuners have a large deterioration in sound quality just by connecting them.
This is something you want to avoid in your effects system.
Equipped with an independent tuner out,
Prevents sound quality deterioration due to the tuner.
Operate other devices
With Loopbone, amps, Headbones, etc.
You can operate products equipped with Slingshot (remote input).
You can switch amplifier channels at the same time as switching loops,
You can switch the amp head with Headbone.
Slingshot out is for various amps, effects, etc.
Foot switch jack To support jack jack
The type and polarity of the control signal can be set.
【spec】
Circuit type: Class-A primary audio circuit
Input impedance: 1meg Ohm at input jack
Drag (TM) control: Variable load matching network
Output impedance: 10K Ohm
Boost level: Unity gain to + 15dB
LED indicators: Large 3mm ultra-bright LED's
Switching: Opto-coupler assisted, 5msec Rise time
Construction: 14 gauge steel, baked enamel finish
Size: 175 x 108 x 54mm
Weight: 1.06kg