Bitte beachten Sie:
1. Für jedes Problem kontaktieren Sie uns bitte, bevor Sie ein schlechtes Feedback oder einen offenen Streit hinterlassen. Wir versprechen, das Problem zu lösen, bis Sie zufrieden sind.
2.Produkt ohne Software-CD und englisches Handbuch senden, weil Standardverpackung ohne dieses Zubehör. Wenn Sie es benötigen, können wir Sie per PDF senden.
Als brandneues Handheld-Oszilloskop der Hantek2000-Serie setzt es das kompakte und leichte Konzept fort, jedoch mit einer neuen Generation von 4-in-1-Multifunktionstestern: Automotive Diagnostic, Oszilloskop, Signalquelle und Multimeter; Ein kleines Volumen des Non-Profit-Griffs von einer Hand; Der Aufhängungsständer wurde entwickelt, um eine Mehrfachwinkelverstellung zu unterstützen; Ultra-Low-Power, Typ-C-Ladeschnittstelle, jede 2 Stunden Akkuladung ermöglicht das Arbeiten einen ganzen Tag oder zwei Monate Standby; High-Definition-Farb-LCD-Bildschirmanzeige klar und empfindlich; Minimalistisches Tastaturdesign vereinfacht die Bedienung, einfach zu bedienen.
Mit mehr als 80 Arten von Autotests und dem Scannen des QR-Codes auf der Rückseite des Geräts können Video-Hilfedateien geöffnet werden, die Ihnen zeigen, wie Sie Fahrzeuge testen.
· Erste Testprojekte: Saugrohr-Unterdruckgrad & Zündung, Lampenruß-Einstellventil Vakuumgrad & Zündung, Abgaszündung (Leerlauf), Abgaszündung (Start).
· Start & Charge: Ladeschaltung, Strom und Spannung.
· Antrieb: Benzin / Diesel.
· Buserkennung: CAN-Bus-Datenbeobachtung, CAN-Bus-Signalintegrität, CAN-Bus-LH-Langzeiterfassung, LIN-Bus.
· Sensoren: Luftmengenmesser, Nockenwelle, Kurbelwelle, Verteiler, Lambdasonde, Drosselklappenstellung. . .
· Zündung: Primär/Sekundär.
· Oszilloskop: 2 Kanäle Oszilloskop, 80MHz Bandbreite, 250M Abtastrate.
· Universelle Multimeterfunktion: Spannung, Strom, Widerstand, Diode, Kondensator, Ein-Aus-Test;
·Ausgangsfunktion des Wellenformgenerators: Sinus-, Rechteck-, Dreieck-, Trapez- und andere Wellenformen ausgeben; Sinus bis 25MHz;
| Model | Hantek2D82AUTO | |||
| Vehicle Testing Mode | ||||
| Vehicle Diagnosis | Vehicle Diagnostic Function | Ignition | Primary Ignition (Voltage) | |
| Primary Ignition(current) | ||||
| Primary Ignition(Voltage& Current) | ||||
| Primary Ignition (Crankshaft Senser) | ||||
| Primary Ignition&SecondaryIgnition | ||||
| Secondary | Secondary Ignition Distributor Type (Plug Lead) | |||
| Secondary Ignition Distributor Type (King Lead) | ||||
| Secondary DIS (Positive-fired) | ||||
| Secondary DIS or CPC (Negative-fired)) | ||||
| Secondary Coil Output Diagnosis | ||||
| Secondary Ignition&Primary Ignition | ||||
| Sensors | Air Flow Meter | Air Flow Meter (Hot Wire) | ||
| Air Flow Meter (Air Vane) | ||||
| Air FlowSensor (BOSCH Diesel) | ||||
| Air Intake PressureSensor (BOSCH Diesel) | ||||
| Camshaft | Camshaft (Inductive) | |||
| Camshaft (AC Excited) | ||||
| Camshaft (Hall Effect) | ||||
| Camshaft (BOSCH Common Rail Diesel) | ||||
| Crankshaft | Crankshaft Inductive Running | |||
| Crankshaft Inductive Cranking | ||||
| Crankshaft Hall Effect | ||||
| Crankshaft Sensor &Primary Ignition | ||||
| Distributor | Distributor Pick-up (Hall Effect) | |||
| Distributor Inductive Pick-up Cranking | ||||
| Distributor Inductive Pick-up Running | ||||
| Lambda Sensors | Lambda Sensor Titania | |||
| Lambda Sensor Zirconia | ||||
| Lambda Sensor Zirconia Pre & Post cat | ||||
| Throttle Position | Throttle Position Potentiometer | |||
| Throttle Position Switch | ||||
| Throttle Pedal Switch (Bosch Diesel) | ||||
| ABS Digital Speed Sensor | ||||
| ABS Analog Speed Sensor | ||||
| Coolant Temperature (5V) | ||||
| Coolant Temperature (GM/Vauxhall Simtec | ||||
| Crash Sensor | ||||
| MAP Analog | ||||
| MAP Digital | ||||
| Hall Effect Road Speed Sensor | ||||
| Accelerator Pedal (Bosch Diesel) | ||||
| Bus Diagnosis | CAN Bus | CAN Bus Data View | ||
| CAN Bus Signal Integrity | ||||
| CAN Bus LH Long Capture | ||||
| LIN Bus | LIN Bus | |||
| Engine | Petrol | Single-point Injector (Voltage) | ||
| Single-point Injector (Current) | ||||
| Multi-point Injector (Voltage) | ||||
| Multi-point Injector (Current) | ||||
| Injector Voltage & Current | ||||
| Injector Current & Primary Ignition | ||||
| Diesel | Common Rail Diesel (Current) | |||
| Injector Bosch CDi 3 (Current) | ||||
| Injector Bosch Diesel (Idling) | ||||
| Injector Bosch Diesel (Accelerating) | ||||
| Diesel Glow Plugs | ||||
| Electronic Fuel Pump | ||||
| Carbon Canister Solenoid Valve | ||||
| ERG Recirculation Solenoid Valve | ||||
| Stepper Motor Example 1 | ||||
| Stepper Motor Example 2 | ||||
| Idle Speed Control Valve (Rotary) | ||||
| Idle Speed Control Valve (Electromagmetic) | ||||
| Throttle Servomotor (Idling) | ||||
| Throttle Servomotor (Accelerating) | ||||
| Bosch CDi3 Quantity Control Valve | ||||
| Bosch CDi3 Pressure Regulator Valve | ||||
| Variable-Speed Cooling Fan On | ||||
| Variable-Speed Cooling Fan Off | ||||
| Variable Camshaft Valve Timing | ||||
| Startup & Charge | Charging Circuits | Charging Circuits Current/Voltage | ||
| Charging Circuits Current/Voltage Starting 24V | ||||
| Charging Circuits Current/Voltage Idling 24V | ||||
| Charging Circuits Alternator AC Ripple/Diode Diagnosis | ||||
| Relative Compression Petrol | ||||
| Relative Compression Diesel | ||||
| Starting Voltage Drop | ||||
| Oscilloscope Mode | ||||
| Bandwidth | 80MHz | |||
| Channel | 2CH+DMM+AWG | |||
| Horizontal | ||||
| Sample Rate Range | 250MSa/s(Single-channel), 125MSa/s(Dual-channel) | |||
| Waveform Interpolation | (sin x)/x | |||
| Record Length | 3K samples per dual-channel | |||
| SEC/DIV Range | 5ns/div~500s/div 1, 2, 5 sequence | |||
| Vertical | ||||
| A/D Converter | 8-bit resolution,each channel sampled simultaneously | |||
| VOLTS/DIV Range | 10mV/div~10V/divat input BNC | |||
| Bandwidth Limit, typical | 20MHz | |||
| Low Frequency Response (-3db) | ≤10Hz at BNC | |||
| Rise Time at BNC, typical | ≤5ns | |||
| DC Gain Accuracy | ±3% for Normal or Average acquisition mode, 10V/div to 10mV/div | |||
| Note: Bandwidth reduced to 6MHz when using a 1X probe. | ||||
| Acquisition | ||||
| Acquisition Modes | Normal | |||
| Trigger | ||||
| Type | Edge | |||
| Mode | Auto, Normal, single | |||
| Level | ±4 divisions from center of screen | |||
| Trigger Level Accuracy | 0.2div × volts/div within ±4 divisions from center of screen | |||
| Slope | Rising, Falling, Rising & Falling | |||
| Source | CH1/CH2 | |||
| Input | ||||
| Coupling | DC, AC or GND | |||
| Input Impedance, | 25pF±3 pF, 1MΩ±2% | |||
| DC coupled | ||||
| Probe Attenuation | 1X, 10X | |||
| Supported Probe Attenuation Factors | 1X, 10X, 100X, 1000X | |||
| Maximum Input Voltage | 150VRMS | |||
| Measurement | ||||
| Cursor | Voltage difference between cursors: △V | |||
| Time difference between cursors: △T | ||||
| Automatic Measurements | Frequency, Amplitude | |||
| Arbitrary Waveform Generator Mode | ||||
| Waveform Frequency | Sine: 1Hz~25MHz | |||
| Square: 1Hz~10MHz | ||||
| Ramp: 1Hz~1MHz | ||||
| EXP: 1Hz~5MHz | ||||
| Sampling | 250MSa/s | |||
| Amplitude | 2.5Vpp(50Ω) | |||
| 5Vpp(High impedance) | ||||
| Frequency Resolution | 0.001 | |||
| Channel | 1CH waveform output | |||
| Waveform Depth | 512Sa | |||
| Vertical Resolution | 12 bit | |||
| Frequency Stability | <30ppm | |||
| Output Impedance | 50 Ω | |||
| DMM Testing Modes | ||||
| Maximum Resolution | 4000 Counts | |||
| DMM Testing Modes | Voltage,Current,Resistance,Capacitance,Diode &On-Off | |||
| Maximum Input Voltage | AC:600V, DC: 800V | |||
| Maximum Input Current | AC: 10A, DC:10A | |||
| Input Impedance | 10MΩ | |||
| Measurement Term | Range | Accuracy | Resolution | |
| DC Voltage | 400.00mV | ± (0.8% + 5) | 100uV | |
| 4.000V | 1mV | |||
| 40.00V | 10mV | |||
| 400.0V | 100mV | |||
| 600.0V | ± (1% + 2) | 1V | ||
| Overload protection: 400mV: 250V, other: 600Vrms. | ||||
| AC Voltage | 4.000V | ± (1.2% + 5) | 1mV | |
| 40.00V | 10mV | |||
| 400.0V | 100mV | |||
| 600.0V | ±(1.5% + 5) | 1V | ||
| Frequency: 40Hz~400Hz; | ||||
| Frequency of 400V and 600V: 40Hz~100Hz | ||||
| DC Current | 40.00mA | ± (1% + 2) | 10uA | |
| 200.0mA | ± (1.5% + 2) | 100uA | ||
| 4.000A | ± (1.8% + 2) | 1mA | ||
| 10.00A | ± (3% + 2) | 10mA | ||
| Overload protection: | ||||
| self restoring fuse: 200mA/250V, 4A and 10A range no fuse. | ||||
| AC Current | 40.00mA | ± (1.3% + 2) | 10uA | |
| 400.0mA | ± (1.8% + 2) | 100uA | ||
| 4.000A | ± (2% + 3) | 1mA | ||
| 10.00A | ± (3% + 5) | 10mA | ||
| Frequency: 40Hz~400Hz; | ||||
| self restoring fuse: 200mA/250V, 4A and 10A range no fuse. | ||||
| Resistance | 400.0Ω | ±(1% + 3) | 0.1Ω | |
| 4.000KΩ | ±(1.2% + 5) | 1Ω | ||
| 60.00KΩ | 10Ω | |||
| 400.0KΩ | 100Ω | |||
| 4.000MΩ | 1KΩ | |||
| 40.00MΩ | ± (1.5%±3) | 10KΩ | ||
| Overload protection: 220Vrms | ||||
| Capacitance | 40.00nF | ±(3% + 5) | 10pF | |
| 400.0nF | 100pF | |||
| 4.000uF | 1nF | |||
| 40.00uF | 10nF | |||
| 100.0uF | 100nF | |||
| Overload protection: 220Vrms | ||||
| Diode | 0V~2.0V | |||
| On-Off | <50Ω | |||
| General Specifications | ||||
| Display | ||||
| Display Type | 2.8 inch64K color TFT | |||
| Display Resolution | 320 horizontal by 240 vertical pixels | |||
| Display Contrast | Adjustable | |||
| Power Supply | ||||
| Supply Voltage | 100V-240VAC, 50Hz-60Hz; DC INPUT: 5VDC, 2A | |||
| Power Consumption | <2.5W | |||
| Fuse | T, 3A | |||
| Battery | 2600mA*2 | |||
| Environmental | ||||
| Operating Temperature | 0~50 °C (32~122 °F) | |||
| Storage Temperature | -40~+71 °C (-40~159.8 °F) | |||
| Humidity | ≤+104°(≤+40°C): ≤90% relative humidity | |||
| 106°~122° (+41°C ~50°C): ≤60% relative humidity | ||||
| Cooling Method | Convection | |||
| Altitude | Operating and | 3,000m (10,000 feet) | ||
| Nonoperating | ||||
| Mechanical Shock | Random Vibration | 0.31gRMS from 50Hz to 500Hz, 10 minutes on each axis | ||
| Nonoperating | 2.46gRMS from 5Hz to 500Hz, 10 minutes on each axis | |||
| Operating | 50g, 11ms, half sine | |||
- Wir akzeptieren nur PayPal.
- Wird nur Paypal-Zahlung mit einer bestätigten Adresse oder von einem verifizierten Mitglied akzeptieren.
- Die Zahlung muss innerhalb empfangen werden 7 Tage.
Wir werden versenden alle Ihre Position (en) sofort INNERHALB VON 24 STUNDEN (Aber wir arbeiten nicht am Sonntag), sobald die Zahlung eingegangen ist.
Bitte überprüfen Sie mit Ihrem eBay & PayPal Lieferadresse vor dem Kauf sehen.
Wir sind nicht in der Lage zu Ihrer Lieferadresse von Nachrichten oder E-Mails ändern.
Tracking-Nummer wird einmal Ihre Position (en) versandt werden.
- 30 Tage Geld-zurück oder tauschen wenn Sie für Ihre Artikel (n) nicht ohne Grund.
- Käufer RETURNS Versandgebühr leisten, einen falschen Artikel für den Kauf.
Bitte senden Sie Ihre Fragen Wenn Sie mehr Informationen über das Produkt (e), Zahlung, Versand oder Rückkehr wissen wollen.
Sie sind auch sehr willkommen, wenn Sie möchten, dass viele Artikel zu bestellen (s).
- Ihre Zufriedenheit ist, was wir aways suchen!
- Wenn Sie mit Ihrem Shopping-Erlebnis zufrieden.
- Es wird sehr geschätzt, wenn Sie uns verlassen könnten Positives Feedback &
. - Wir freuen uns, für alle Fragen der Transaktion zu helfen.