C800 Head Up Display GPS Dual System Alarm Speed Projector RPM Fuel Consumption
Features
This product Design Patent and Display Images Copyright had been registered with customs record
Kindly attention:Working voltage: 11V~18VDC (12vdc/200ma),please use a USB cable when voltage higher than 24V.
Introduction
HUD short for Head Up Display.It displays driving data on thecarwindshield such as speed,RPM,watertemperature,trip distanceetc;avoiding driversunsafelybecause of watching the instrument while driving.Drivers can read the driving information instantly, and always keep the best state on the way with HUD.
Display Functions
1.RPM(OBD mode), Satellite numbers(GPS mode)
2. OBD mode:Battery voltage/Fuel consumption/Satellite numbers
GPS mode:Battery voltage/Satellite numbers
3.Icons: Satellite signal / Error code /Fatigue driving /Driving direction
4.Speed unit:KM/H=kilometer/hour, MPH=Mile/hour
5.V=Unit of voltage, LKH=Unit of fuel consumption,including Instantaneous fuel consumption (idle speed),100 km instantaneous fuel consumption (in driving),Average fuel consumption (after driving)
6.Multi functions display:OBD mode:RPM,single trip distance,altitude,driving time,clock,water temperature,driving direction
7.GPS mode:Clock,driving direction,single mileage,altitude,driving time
8.Unit icons :RPM=engine speed, Trip=trip distance, ASL=Altitude, MIN=driving time,℃/F=Water temperature
1.Setting button
This product Design Patent and Display Images Copyright had been registered with customs record
Kindly attention:Working voltage: 11V~18VDC (12vdc/200ma),please use a USB cable when voltage higher than 24V.
Introduction
HUD short for Head Up Display.It displays driving data on thecarwindshield such as speed,RPM,watertemperature,trip distanceetc;avoiding driversunsafelybecause of watching the instrument while driving.Drivers can read the driving information instantly, and always keep the best state on the way with HUD.
Display Functions
1.RPM(OBD mode), Satellite numbers(GPS mode)
2. OBD mode:Battery voltage/Fuel consumption/Satellite numbers
GPS mode:Battery voltage/Satellite numbers
3.Icons: Satellite signal / Error code /Fatigue driving /Driving direction
4.Speed unit:KM/H=kilometer/hour, MPH=Mile/hour
5.V=Unit of voltage, LKH=Unit of fuel consumption,including Instantaneous fuel consumption (idle speed),100 km instantaneous fuel consumption (in driving),Average fuel consumption (after driving)
6.Multi functions display:OBD mode:RPM,single trip distance,altitude,driving time,clock,water temperature,driving direction
7.GPS mode:Clock,driving direction,single mileage,altitude,driving time
8.Unit icons :RPM=engine speed, Trip=trip distance, ASL=Altitude, MIN=driving time,℃/F=Water temperature
1.Setting button
2.System/Mode switch:pull up the setting button to enter into OBD mode,pull down for GPS mode
OBD mode functions(only for OBD2 & EUOBD vehicles)：speed,RPM,water temperature,voltage,fuel consumption,trip distance,driving time,clock
GPS mode functions:speed,voltage,satellite numbers,altitude,driving direction,driving time,clock
GPS mode functions:speed,voltage,satellite numbers,altitude,driving direction,driving time,clock
3.USB port
When the setting button in theright
1.Short pull up:(1)switch the voltage and fuel consumption
(2)to add the default value after entering into the the setting mode
2.Short pull down:(1)switch the water temperature/trip distance/driving time/clock/speed-up test (2)to decrease the default value after entering into the the setting mode
3.Short press in:(1)switch the display mode (2)add the menu after entering into the setting mode
4.Long pull down:turning off/on the alarms
5.Long pull up:all lights will be on, to eliminate the fault code, do it again to save and exit
6.Long press in:to enter into the setting menu(menu 1-11,details please refers to the manual),when finish the adjustment, long press in the button to save and exit
Factory reset
When the HUD turns off, long press-in the wave button and at the same time turn on the HUD, all theLEDlights will be on, and then release the button, the reset finished.(details please refer to the setting menu table)
Clear the fault code：(works after OBD received signal)
When HUD is power on, long pull up the button for 5 seconds, then all the lights will be on, it means finished, do it again to save and exit
Turn off/on the buzzer
When HUD is working,pull down the setting button for 5 seconds,to turn off the buzzer,do it again to turn on the buzzer
HUD Setting
Vertical long press in the setting button for 5s to enter the menu setting, vertical short press to increase the menu option(from menu 1 to menu 16), up and down the setting button to increase or decrease the parameter value. After adjustment, vertical long press 5 seconds to save and exit.
Please note:If the car will not use in a week,please disconnect the OBD equipment.
OBDTroubleshooting
1.The screen without any display, and no power
Start the car engine; check if the OBD cable line is tight; please pull down the OBD cables more times to ensure; check if HUD power switch turns on. If still no display, please change another car to test, analyze whether the car OBD diagnostic interface is good, if it is not good, please repair it and try again.
2.When HUD power on, HUD only shows the car voltage and be automatic power off aftera fewseconds driving.
HUD only available for cars with OBD2 and EU-OBD agreement(European region: after 2003 years, Other region: after 2007 years）
HUD Products don’t support JOBD and OBDI protocol.
3.The machine is stuck or stuck during driving
(1)Please check the OBD interface if connected withe other device(One point and two lines,positioner, tire pressure monitoring, drop lock window folding, ELM27 etc)
(2)Modified and retrofitted cars (Central Control Navigation, Electronic Throttle Accelerator ,Fixed Speed Cruise, Computer System has been brushed,One-button start, keyless entry, remote start) will cause a crash
Please remove other OBD devices and do the factory reset.
4.Inaccurate Speed
(1)First check the speed unit is correct or not, the speed unit including KM/H and MPH
(2)When HUD is power on, vertical press the setting button for 5 seconds to enter into the menu1and the parameter shows 107,up or down the setting button to increase or decrease the value according to the difference until it shows correct one. After adjustment, vertical press in 5 seconds to save it.(Example:If the dashboard shows 100,and HUD shows 103,then change the HUD default value from 107 to 104)
5.Inaccurate fuel consumption
The unit for fuel consumption is L/100KM, HUD display is the single driving fuel consumption, while car display is Integrated average driving fuel consumption, so it is normal if there are difference.
HUD display three kinds of fuel consumption
a. Idle mode: HUD display Instantaneous fuel consumption per hour (L/H), it means HUD can figure out how much oil the car will consumed after start engine in one hour
b. Driving mode: HUD display Instantaneous fuel consumption of 100KM
c. Finish driving: HUD display is average fuel consumption of 100KM, when turn off the car, HUD will auto turn off in 10s.
6.Clock calibration
When HUD is power on,long press in for 5 seconds to enter the setting menu,short press in the button set to menu 15,Pull up to add the GMT time,Pull down to decrease the GMT time ,once finished,long press in the button fro 5 seconds to save and exit.
7.Stop-star cars
Vertical press in 5 seconds to enter into menu setting, short press 14times to menu 14, the default parameter is 20, up or down change it to 180, then power off time will be 3 minutes,then vertical press in 5 seconds to save and exit,HUD will power off in 3 mins.
8.HUD cannot automatically turns off (RPM and Speed are not off set)
Vertical press in 5 seconds to enter into menu setting, short press 13times to menu 13, the default parameter is 0, up or down change it to 13.2V orhigher, vertical press in 5 seconds to save and exit.
GPS Troubleshooting
1.The screen without any display, and no power
1.OBD line connection case: Start the car engine, HUD in order to prevent power consumption, the start voltage set to 13.2 volts, as long as the car after the voltage reached 13.2 volts to automatically boot, check the OBD line or car charging line is connected to the elastic, pull down repeatedly plug several times, with a USB cable into the cigarette smoke device
1.Short pull up:(1)switch the voltage and fuel consumption
(2)to add the default value after entering into the the setting mode
2.Short pull down:(1)switch the water temperature/trip distance/driving time/clock/speed-up test (2)to decrease the default value after entering into the the setting mode
3.Short press in:(1)switch the display mode (2)add the menu after entering into the setting mode
4.Long pull down:turning off/on the alarms
5.Long pull up:all lights will be on, to eliminate the fault code, do it again to save and exit
6.Long press in:to enter into the setting menu(menu 1-11,details please refers to the manual),when finish the adjustment, long press in the button to save and exit
Factory reset
When the HUD turns off, long press-in the wave button and at the same time turn on the HUD, all theLEDlights will be on, and then release the button, the reset finished.(details please refer to the setting menu table)
Clear the fault code：(works after OBD received signal)
When HUD is power on, long pull up the button for 5 seconds, then all the lights will be on, it means finished, do it again to save and exit
Turn off/on the buzzer
When HUD is working,pull down the setting button for 5 seconds,to turn off the buzzer,do it again to turn on the buzzer
HUD Setting
Vertical long press in the setting button for 5s to enter the menu setting, vertical short press to increase the menu option(from menu 1 to menu 16), up and down the setting button to increase or decrease the parameter value. After adjustment, vertical long press 5 seconds to save and exit.
Please note:If the car will not use in a week,please disconnect the OBD equipment.
OBDTroubleshooting
1.The screen without any display, and no power
Start the car engine; check if the OBD cable line is tight; please pull down the OBD cables more times to ensure; check if HUD power switch turns on. If still no display, please change another car to test, analyze whether the car OBD diagnostic interface is good, if it is not good, please repair it and try again.
2.When HUD power on, HUD only shows the car voltage and be automatic power off aftera fewseconds driving.
HUD only available for cars with OBD2 and EU-OBD agreement(European region: after 2003 years, Other region: after 2007 years）
HUD Products don’t support JOBD and OBDI protocol.
3.The machine is stuck or stuck during driving
(1)Please check the OBD interface if connected withe other device(One point and two lines,positioner, tire pressure monitoring, drop lock window folding, ELM27 etc)
(2)Modified and retrofitted cars (Central Control Navigation, Electronic Throttle Accelerator ,Fixed Speed Cruise, Computer System has been brushed,One-button start, keyless entry, remote start) will cause a crash
Please remove other OBD devices and do the factory reset.
4.Inaccurate Speed
(1)First check the speed unit is correct or not, the speed unit including KM/H and MPH
(2)When HUD is power on, vertical press the setting button for 5 seconds to enter into the menu1and the parameter shows 107,up or down the setting button to increase or decrease the value according to the difference until it shows correct one. After adjustment, vertical press in 5 seconds to save it.(Example:If the dashboard shows 100,and HUD shows 103,then change the HUD default value from 107 to 104)
5.Inaccurate fuel consumption
The unit for fuel consumption is L/100KM, HUD display is the single driving fuel consumption, while car display is Integrated average driving fuel consumption, so it is normal if there are difference.
HUD display three kinds of fuel consumption
a. Idle mode: HUD display Instantaneous fuel consumption per hour (L/H), it means HUD can figure out how much oil the car will consumed after start engine in one hour
b. Driving mode: HUD display Instantaneous fuel consumption of 100KM
c. Finish driving: HUD display is average fuel consumption of 100KM, when turn off the car, HUD will auto turn off in 10s.
6.Clock calibration
When HUD is power on,long press in for 5 seconds to enter the setting menu,short press in the button set to menu 15,Pull up to add the GMT time,Pull down to decrease the GMT time ,once finished,long press in the button fro 5 seconds to save and exit.
7.Stop-star cars
Vertical press in 5 seconds to enter into menu setting, short press 14times to menu 14, the default parameter is 20, up or down change it to 180, then power off time will be 3 minutes,then vertical press in 5 seconds to save and exit,HUD will power off in 3 mins.
8.HUD cannot automatically turns off (RPM and Speed are not off set)
Vertical press in 5 seconds to enter into menu setting, short press 13times to menu 13, the default parameter is 0, up or down change it to 13.2V orhigher, vertical press in 5 seconds to save and exit.
GPS Troubleshooting
1.The screen without any display, and no power
1.OBD line connection case: Start the car engine, HUD in order to prevent power consumption, the start voltage set to 13.2 volts, as long as the car after the voltage reached 13.2 volts to automatically boot, check the OBD line or car charging line is connected to the elastic, pull down repeatedly plug several times, with a USB cable into the cigarette smoke device
2.HUDcannot be automatically powered on or repeatedly extinguished during driving
UnderOBD line connection:HUD will turn off when voltage lower than 13.2v.Vertically press the button in(5s)to enter into menu 11,adjust the default parameter 13.2 to 12.8 or 12.6.
If still can't solve,please use the USB and connects to the car cigarette light
3.HUD doesntautomaticallyturn off after flame-out
OBD line connection:the default turnoffvoltageis13.2v.HUD will auto on when voltage higher than 13.2,oppositely,it will auto off.Please enter into menu 11 and change the parameter to 13.5 when your HUD cannot automatically off.
If still can’t solve,please use the USB and connects to the car cigarette light
4.Inaccuratespeed
Power on the case, vertical long press the Dial key 5 Seconds to enter the menu options, menu display 0, parameter value 107, depending on how much difference you and the instrument panel, on the dial or allocated, increase and decrease, the difference in the speed value. After adjusting, the dial key is pressed vertically for 5 seconds to exit.
Technical Parameters
1.Environment temperature:- 40°C— +120°C
Barometric press: 86-106KPa
Relative humidity:10%-95%
Environment voice:<=60dB
2.Work voltage:11V~18Vdc(12Vdc/200mA)
3.Sleep current:<=30mA
4.Display way:Virtual image reflection
5.Display channel :LED Display
6.Reflector transmittance: 98%
Package Includes
1 x Head Up Display
