Bond It Contact Adhesive Solvent Based High Grab Neoprene Glue 250ml/500ml/1/5L

Description:
A premium grade, solvent based, yellow/ beige coloured, single component solvent‐based contact adhesive.
THIS PRODUCT IS TOLUENE‐FREE.

Uses
CONTACT ADHESIVE can be used for bonding cork, leather, rubber,
metals, wood, chipboard, hardboard, laminated plastics (e.g.
Formica), dense textiles, plaster, stone, concrete, cementitious
screeds and smoothing compounds. It will bond rigid PVC and
uPVC sheets but the materials should be checked for suitability
prior to application as solvent attack can occur in some instance.
Bond It CONTACT ADHESIVE may also be used to bond lightweight
materials to vertical surfaces and ceilings. It is predominantly
designed for interior use but can be used externally when the
adhesive is protected from direct sunlight and water.
This product is not suitable for polystyrene, polythene,
polypropylene, silicone rubbers, bitumen or PTFE. The solvent in
the contact adhesive may attack certain painted or lacquered
surfaces.

Preparation
Surfaces to be bonded must be clean, dry and free from dust,
grease or contaminants that may hinder adhesion. Whenever
possible, materials should be conditioned overnight in ambient
conditions of 15-20o
C/ 60-65%RH. Very smooth surfaces should be
abraded to provide an adequate key.

Application
Stir the glue thoroughly, prior to use, until a uniform consistency is
obtained.
Apply the adhesive to both surfaces being bonded with a notched
scraper, brush or trowel to produce a thin film. In cool, damp
conditions take care that no condensation takes place on the glue
lines as it will affect the adhesive bond. If condensation (evident
by a grey "bloom" on the glue) does occur delay bonding until the
glue is moisture-free. If the open time is exceeded, re-apply the
adhesive to both surfaces. Leave the adhesive to become touch
dry (approx 5-30 minutes depending on drying conditions).
Carefully align pieces to be bonded. For panel products, work from
the centre outwards to minimise air entrapment. Press the two
surfaces together and apply firm pressure with a hand rubber
roller, block and mallet or mechanical press. Handling and
trimming are possible immediately after bonding.

Note: as all surfaces differ, it is recommended that this product is
tested on a small area to determine suitability before use. It is the
users' responsibility to determine suitability.

Drying Time
Allow up to 60 minutes for initial set. Bond strength will continue
to increase for up to 48 hours after application. Do not use
infrared heaters or mechanical blowers as the product contains
solvent and is highly flammable. Total drying time depends upon
ambient temperature and the thickness coverage of the adhesive.
For best heat resistance leave at room temperature for 7 days
before subjecting to in service temperature of up to 80oC

Limitations
- Not suitable for use with polyolefins or acetate fabrics.
- Do not use on soft (plasticised) PVC or polystyrene.
- Do not use on cellulose painted surfaces or on bitumen.
- Not suitable for items that may hold hot liquids.
- Do not use in areas subject to continuous immersion in
water.
- Do not use at temperatures below 5oC.

Colour
Yellow/ beige in colour.

Container Size
Available in 250, 500, 850ml and 5L metal tins.

Coverage
5m2 per litre when applied by notched spreader;
8m2 per litre when applied by brush.

Storage Life
18 months from date of manufacture, when stored in original,
unopened containers.

Storage Conditions
Containers must be kept sealed and stored under cover, away
from sources of heat and ignition. Keep out of direct sunlight at a
temperature of between 5-25oC.

Cleaning Of Tools
Excess material can be removed by using acetone or nail polish
remover (protect any surrounding surfaces).

Disposal of Containers
Do not leave empty containers where residue could be harmful to
children, animals or the environment. Replace lids and remove
any containers to a central disposal point in accordance with local
regulations.

Health & Safety
Contains ethyl acetate, acetone, C6-C9 Hydrocarbons, n-alkanes,
isoalkanes, cyclics. Please refer to separate material safety data
sheet for full handling, use and storage instructions. Keep out of
reach of children. It is the users responsibility to determine
suitability for use. If in doubt contact our Technical Department
for advice.
Note: this information is for general guidance only, since site conditions
and labour are beyond our control. It is recommended that users make
their own tests to determine suitability.

Health & Safety
Contains ethyl acetate, acetone, C6-C9 Hydrocarbons, n-alkanes,
isoalkanes, cyclics. Please refer to separate material safety data
sheet for full handling, use and storage instructions. Keep out of
reach of children. It is the users responsibility to determine
suitability for use. If in doubt contact our Technical Department
for advice.
Note: this information is for general guidance only, since site conditions
and labour are beyond our control. It is recommended that users make
their own tests to determine suitability.

CURED ADHESIVE
Service Temperature -60°C to +80oC
Cloth backed PVC leather to wood >20N/50mm
Cloth backed PVC leather to painted steel >20N/25mm
Coverage 5-8m2 per litre

Product Details:
Size: 25ml, 500ml, 1 Litre & 5 Litre

Package Content
Bond It Contact Adhesive Solvent Based Neoprene Glue High Grab DIY Heavy Duty

Available Sizes:
250ml, 500ml, 1 Litre & 5 Lites