Bond It 5L SBR Waterproof Concrete Latex Admixture Wall & Floor Bonding Agent UK

 
Description
A premium grade SBR designed to give concrete floors and cement renders abrasion, chemical and water resistance. Bond It SBR also shows improved performance as a key coat adhesive compared to non SBR bonding agents.

Uses
For improving a mortar's, render's or floor screed's
abrasion and chemical resistance. Providing
protection during continued or intermittent water
contact suitable for both external or internal use
application. Key coat applications to substrates with
a low porosity. For repair patching of concrete and
cement screeds, to improve adhesion and flexibility
of screeds.

Application
All surfaces should be free from laitance, oil, grease
and standing water. Unsound surfaces should be
scabbled down to a solid base material.
Key Coat: Mix 1 part Bond It SBR to 2 parts cement
by volume and adjust to brushable consistency with
water. Mix only enough to use within the hour.
Brush thoroughly into a clean dust free substrate,
whilst still wet overcoat with the floor or render mix.
Damp­proofing: Mix the same formulation as in the
key coat and apply the first coat with vigorous brush
strokes. Allow to touch dry then apply a second coat
at 90° to the first and allow 48 hours to dry. Apply
the third coat at 90° to the second coat and while
still wet apply the render.

Renderings/Mortars: Prepare the substrate with the
key coat first for best results. Mix sand/cement
mortar/render and add 5­7.5 litres Bond It SBR per
25Kgs cement, reducing the amount of gauging
water accordingly. Apply at least 6mm thick. Two
coats are recommended.

Granolithic Floorings: Prepare the substance with
the key coat first for best results. Mix cement: sand:
3mm granite flooring chips 1: 1½: 1½ Use 5L Bond
It SBR to each 25Kg of cement, for floors up to
25mm thick. For floors greater than 25mm use 2.5
litres Bond It SBR and add water accordingly to
produce a semi­dry mix.
Patching Concrete: Use the key coat and use a 3:1
render mix feathering lightly.

Limitations
Protect from freezing. Do not use with cements other
than OPC without first contacting the cement
supplier. Do not use chloride based frost proofers
with Bond It SBR. Do not over mix mortar/render.

Storage Conditions
Store in cool, dry conditions. Protect from frost, high
temperature and sunlight.

Shelf Life
Up to 24 months when stored according to
manufacturers instructions.

Coverage
Flooring: 5 litres SBR for every 25Kgs cement.
Mortar/Rendering: 5­7.5 litres SBR for every 25Kgs
cement.
Key Coat: 5 litres SBR per 30m² depending on
porosity.

Disposal of Containers
Do not leave empty containers where residue could
be harmful to children, animals or the environment.
Replace lids and remove any containers to a central
disposal point in accordance with local regulations.

Safe Handling Precautions
Please refer to separate material safety data sheet
for full handling, use and storage instructions. Keep
out of reach of children. It is the users responsibility
to determine suitability for use. If in doubt contact
our Technical Department for advice.

Note: this information is for general guidance only, since site
conditions and labour are beyond our control. It is
recommended that users make their own tests to determine
suitability

Specification Summary
Appearance Milky White Liquid capable of florescence
Flammability Non Flammable
pH approximately 10.5
Solubility in water Soluble
Boiling Point 100oC (water)

Container Size
Code: BDH040
Size: 5L
Barcode: 5060021361196

Package Content
SBR ADMIXTURE Mortar/rendering Admixture and Bonding Agent