2PC Bond It Silicone Sealant Remover Cured Non Drip Gel Adhesive DE-BOND Mate 125ml

Description:
A non‐drip gel formula for the complete removal of cured silicone sealant, particularly when silicone has been
accidentally smeared over glass, ceramics or counter tops.

Uses
SILICONE SEALANT REMOVER chemically digests cured and uncured
silicone elastomers and polymers, leaving their remnants easy to
rinse away with water or solvent. Should be used to remove old
silicone sealant during renovations. It is suitable for use on brick,
concrete, PVCu, melamine laminates, acrylic, uncoated aluminium
and its alloys, copper and its alloys, iron and steels, glass and
ceramics, epoxy composites without adverse effect. Has little
impact on rubber and non silicone elastomers or most painted
surfaces, however it is advisable to always test a small area before use.

Application
Product is ready to use and should not be diluted. Ensure the
surface of the material is completely dry. Cut away as much of the
silicone as possible with a knife or sharp blade. Protect any
surrounding paint work with masking tape. Extrude the gel over
the old silicone, being careful to avoid areas of correctly applied
sealant. The depth of cover should be at least twice as deep as the
depth of silicone to be removed. Allow to stand for at least 2
hours (this may vary depending on the characteristics
of the silicone and substrate but are typically between 2 to 12
hours.) Wipe clean with a paper tissue or dry cloth and ensure all
traces of solvent are removed. Repeat the process if necessary.
Keep some water handy to deactivate any runs.
Surfaces should be degreased with a solvent, such as methylated
spirit, before applying fresh sealant.

Limitations
Do not use on nylon, re-enamelled or plastic coated metals. If in
doubt, try a small area first. The gel should be applied to dry
surfaces only and under dry weather conditions. If the gel comes
into contact with water, the active ingredients will be deactivated
and the gel rendered un-usable. The gel will not completely
dissolve silicone sealant but will break down the adhesion of the
sealant to the substrate to facilitate removal.

Container Size
125ml plastic cartridge.

Colour
DE-BOND-MATE is light pinkish/brown in colour.

Shelf Life
12 months from date of manufacture when stored in unopened
tubes.

Storage Conditions
Store in cool, dry conditions at a temperature between 5-30oC.
Protect from frost.

Disposal of Containers
Do not leave empty containers where residue could be harmful to
children, animals or the environment. Remove any containers to a
central disposal point in accordance with local regulations.

Health & Safety
Please refer to separate material safety data sheet for full
handling, use and storage instructions. Keep out of reach of
children. It is the users responsibility to determine suitability for
use. If in doubt contact our Technical Department for advice.

Note: this information is for general guidance only, since site conditions
and labour are beyond our control. It is recommended that users make
their own tests to determine suitability.

Specification Summary
Appearance Pinkish/ brown gel
Solubility in Water Soluble
Storage Temperature Between 5 and 30oC
Unworked Penetration 260-300
Flashpoint >75c
Coverage 1 cartridge should be enough to remove 5m of silicone bead
UFI QF60-U0FC-S00S-0T26
A safe, low odour formulation that does not contain halogenated
solvents, heavy metals, cyanide or water.
Minimal hazard rating and its active substances are biodegradable.
This product does not contain dichloromethane.

Product Details:
Colour: Pinky/brown
Code: DBON1125-2PC
Size: 125ml
Barcode: 5060021369406

Package Content
2PC Bond It Silicone Sealant Remover Cured Non Drip Gel Adhesive DE-BOND Mate 125ml