Replacement for Blue Ox BX88368 EZ Light Wiring Kit

For Jeep Wrangler JL & Gladiator 2 Door & 4 Door,

Replacement For Blue Ox

👍【Designed for Jeep JL & Gladiator】

BX88368 EZ Light Wiring Kit Designed to universally

Fit for 2018 2019 2020 2021 2022 2023 Jeep Wrangler JL and 2020 2021 2022 2023 Jeep Gladiator.

Trailer Towing Harness is perfect for used at both 2-Door & 4-Door and with & without Tow Package.

Also suitable for 2018-current Jeep JL & JLU Wrangler Unlimited Rubicon, 4xe 4x4 Sahara, Sport, Sport S, 80th Anniversary, High Altitude, Islander, Willys , Willys Sport and more.

👍【Solid & Secure Plug】

T-connector harness goes on both driver's side and passenger side. Prewired trailer hitch tow connector plugs directly into for Jeep Wrangler / Jeep Gladiator existing wiring harness, which is located behind tail lights. 4-way connector stowed beneath your vehicle, near the trailer hitch, with tight-fitting rubber dust cover and bracket to protect socket terminal from dust and water damage. Could be cut (save white wire) to match different pole plug.

👍【Durable Construction】

The cable features a good length of wire to route for your vehicle. Heavy-duty bonded wire and premium tin-plated copper terminals perform in great corrosion-resistant and conductivity. Waterproof and chemical resistance. Zip ties included to cinch up all wires.

👍【Quick & Easy to Transfer Signals】

Sturdy EZ Light Wiring Kit let you quickly and easily take all the lighting signals from your motor home or RV to the back of vehicle. Allow people behind you to know your attentions when going down the road. This includes your left turn signal, right turn signal, tail lamp and brake lamps. Keeping you safe and compliant in all states.

👍【Plug & Play Installation】

Custom fit and easy to install within 15 minutes. No changing, cutting or splicing anything about your vehicle's wiring. Installation manual included. Simply mount converter box, connect 2 T-connectors to driver’s side taillight socket and vehicle wiring harness. Route 4-Flat harness to front of vehicle and secure bracket and wire. Then, you're ready to go. Package includes EZ wiring kit, bracket and installation hardware, zip ties, dielectric grease.

👍【Package Included】

BX88368 EZ Light Wiring Kit.

👍【Easy Installation】

1. Remove the vehicle’s taillight assemblies from both the driver’s and passenger’s side by removing the two screwsthat are toward the inside of the vehicle. Being careful not to break the alignment tabs, disconnect the taillight housing from the vehicle.
2. Mount converter box on driver’s side behind the driver’s side taillight, using the double stick tape.
3. Disconnect the vehicle wiring harness from both taillight sockets. Plug the wiring kit connector with the yellow wire into the mating connectors on the driver’s side taillight socket and vehicle wiring harness.
4. Route the wiring kit connector with the green wire down through the opening between the vehicle frame and body to the passenger’s side avoiding the exhaust and areas that would cut or pinch the wire. Route the wiring kit connector with the green wire up through the opening on the passenger’s side between the frame and body.
5. Plug the wiring kit connector with the green wire into the mating connector on the passenger’s side taillight socket and vehicle wiring harness.
6. Secure all loose wiring behind taillight assembly with the provided nylon zip ties. Route the 4-Flat harness out of the lower rear driver’s side to front of vehicle. Secure wire to vehicle with nylon zip ties.
7. Reinstall the taillight housing assembly, positioning the wire harness between the housing and the vehicle body. Secure the remainder of the wiring kit harness under the bumper, or behind the taillight housing, with nylon zip ties. Be careful to avoid any areas that would cut or pinch the wire.
8. Install 4-Flat end of harness (from rear of vehicle) into the 4-Flat bracket. Mount the 4-Flat bracket using screws provided in a convenient location at the front of the vehicle.
9. Locate a suitable grounding point near the connector. (Do not drill into vehicle floor or bed.) Clean dirt, paint and rust proofing from area. Drill a 3/32” hole and secure white wire with ring terminal using screw provided. Do not drill into any exposed surfaces.
10. Apply a small amount of grease (provided) to the 4-Flat terminals to prevent corrosion. Connect to RV electrical system and test all functions with the engine running to ensure proper operation