Kinetico Water Softener Problems Fixed
Kinetico water softener problems can happen when sections of the
Kinetico water softener control head breaks down. Parts inside the
head such as the control valve which has two very important seals.
The quad ring seal, and the taper seal, these are prone to wearing
out.
This also applies to the drain valve seals. The Kinetico drain
valves have similar problems where they can wear on four edges.
Another problem can happen when the Kinetico main piston seals
wear on four edges, these are hidden seals which often get
overlooked. The balance piston seal can cause problems too.
The very small advance seal located on the Kinetico actuator is
particularly prone to wearing out. Generally, all the parts of the
Kinetico need to work together to form a whole. The Kinetico pawl
set, Kinetico control disk and Kinetico water meter disk must also
be in perfect condition.
Brine tank resin can last up to 30 years, but needs to be good.
Kinetico resin is installed in both the main tank and the remote
tank. For best performance it is recommended to fit Kinetico
resin. Resin is not generally a problem on the Kinetico, as 99% of
all faults are linked with worn, non functioning seals.
Kinetico level one, has the most complex parts. This Kinetico
level has the gears, the control disk, and the meter disk. The
pawl set is located on this level, as is the balance piston and DO
cap. We show how to check this level.
Kinetico level two has the vent tube and the brine flow control,
the brine flow control can get blocked.
Kinetico level three has the venturi throat and the throat on
this part of the Kinetico must be clear and perfect. We explain
how to do this.
Kinetico level four contains the main Kinetico piston flat seals
and quad rings. Also, this level has the Kinetico control valve
and quad rings, and of course the taper seal sets. In addition,
there is the Kinetico backwash flow control. This need to be clear
and clean.
Kinetico level five has the drain valves and quad rings. The
Kinetico five level has the Kinetico interlock and the cut
outs for the Kinetico check stems. Older versions have the small
blue Kinetico balls that do the same job, to stop back flow in the
system.
Kinetico level six has the Kinetico check stems, and the Kinetico
upper distributor. The entire head is attached to the main
Kinetico resin bottle by a large thread and immediately below that
the upper distributor.
The Kinetico seals involved in keeping this softener working are
many, and only one Kinetico seal needs to be faulty to cause
everything to fail. We work through everything in detail in our
Kinetico videos. We show you a one minute run through in our ebay
listing. We have many videos in detail, in fact detailed video for
every level. Hours of information and explained by our Kinetico
engineer. Follow his work to get your Kinetico water softener
working properly.
💦 BEFORE WE DO
ANYTHING💦
We Need to Test Your Water
Here's How We Do That
WHAT DO WE WANT FROM YOUR KINETICO SOFTENER?
🚿 We Want Beautiful Softened Water From it. 🚿
We Send You Our Simple Test Kit
We check the "HARDNESS" level of the water.
HARD WATER DESTROYS EVERYTHING IT TOUCHES
So, we check the water first before you start rebuilding.
It's best to take a look at the water coming from your
softener first.
We provide 4 Dip-Tests to check your system before rebuild and
after. This is very simple to do.
You Can Check Before Rebuild and Afterwards
⭐⭐ Get Our Seal Kit - Videos - Engineers Guide
⭐⭐
A VERY SIMPLE FIX IN A COUPLE OF HOURS
Saving You at Least $500
The Full Detailed Video Shows You What You Need And How to
FIX IT
<<< PROBLEMS LIKE >>>
A tiny balance piston seal fault will cause your softener to
continually run to the drain. This seal is probably
responsible for 50% of all faults. It cost less
than $1.00 and will solve a huge percentage of problems.
What do SOME Kinetico Engineers tell their
customers?
You probably need a new control head.
COSTING HUNDREDS OF DOLLARS.
An Engineers visit will cost you at least $120 per hour, maybe
more. With an average repair bill of over $500
<<< Follow Our Video >>>
<<< A Trained Kinetico Engineer Will Show You How
>>>
A Full Walk Through
Over 3 Hours Of Tutorials
⭐⭐⭐ Here's The Amazing Thing ⭐⭐⭐
Spare Parts Are Often NOT NEEDED
We Show You WHY -
And, if you do need parts, you just buy the seals you
need.
Not the entire block or head.
WE SHOW YOU WHAT NO OTHER KINETICO DEALER WILL SHOW YOU
Repairs at a fraction of the price...
Often a full rebuild will cost less than $150.00
SAVE HUNDREDS OF $$$$$$$$$ TODAY
⭐THIS KIT INCLUDES THE MAIN SEALS KITS⭐
Kinetico Water Softener Re-Build Kits
⭐ Fits All Kinetico Softeners ⭐
Universal Kinetico Softener Head Design
Upgraded Complete Seal Kit For All Kinetico Softener
Heads
Kinetico Parts Included in this Kit
The kit comprises:
Control Valve Quad Ring Seals
Purge Valve Quad Ring Seals
Drain Valve Piston Quad Ring Seals
Drain Valve Internal Piston Quad Ring Seals
Outlet Valve Piston Quad Ring Seals
Outlet Valve Internal Piston Quad Ring Seals
Actuator O ring seals
Balance piston internal O rings seals
⭐⭐⭐THESE ARE NO ORDINARY SEALS⭐⭐⭐
High Quality 4 Sides X Ring/Quad ring can often our exceed
the originals in terms of quality. We guarantee the quality.
When these softeners get neglected and not serviced
properly they often are not working to their full potential.
They can "eat" salt like you wouldnt believe and not work at all
efficiently. Almost all faults are solved by replacing a few essential seals
within the water softener head itself.
Will this service Video apply and internal spare parts kit fit
your Kinetico Water Softener?The simple answer is yes. The water softener head has a specific design and those very
important seals will fit all designs.
They are all special seals that need to be a precise fit,
consisting of the special X seals or Quad seals;
these seals need to be fitted properly.
Full contents of Video are shown here below.
⭐⭐ EXTRA EXTRA EXTRA EXTRA ⭐⭐
This kit now includes the Brand New Resin Change Video
Brand New Videos - Video Format - Shows Step by Step
Shows EXACTLY how to do the entire job!
SAVING YOU HUNDREDS OF $$$$$$$$$$
40 Minute Video - Easy to Follow
***Watch in Real Time***
You will not get these parts from your local Kinetico
dealer?
Kinetico have a policy of only supplying parts to their
authorised installers and dealers. In addition, they do
not sell the quad rings and O ring seal kits, nor do they
supply these parts to dealers.
They only sell entire component blocks or levels where the
cost to you is much higher, often hundreds of dollars higher;
99.99% of the time the large components that Kinetico service
engineers would fit only require small seals fitting.
These components include the inlet and purge valves
which mostly only require new quad rings, together with drain
valves and control valves, and some other simple seals and
parts; these mostly solve most of the faults that
Kinetico softeners develop.
If your Kinetico Softener looks similar to the one shown here
our Rebuild Kit will fit your softener.
If your Kinetico head, looks like this model shown above,
maybe has different resin storage, you will be able to service
yours too. The design is common to all
softeners. Most Kinetico water softeners will run for many years without
fault.
However, when faults do occur the actual fault is often a very
simple thing to rectify; what is more, they mostly only need
cleaning to bring back to life.
The Videos will show you how to break down, clean/service and
assemble.
We show clearly main problem points and what to look out
for.
We include breakdown of parts and fault finding in PDF
format.
We include full exploded drawings of Water Softener
PDF
We include full fault finding diagnosis charts PDF
We include detailed descriptions of parts PDF
There is a full detailed breakdown of the Kinetico water
softener metering system head and full breakdown of all levels of the head. The Video provides a full tutorial
which you can use to dismantle and re-assemble.
We show where to clean and where to use the important
silicone grease to maintain. Save a fortune on Service calls. Ideal if you wish to buy a used one and want to service
yourself. Complete package deal here…
⭐Hours of Video to Watch in Real Time⭐
Our Kinetico Engineer Shows You How
**** The Unique Kinetico Re-Build Pack ****
Kinetico Water Softener Service Pack
Complete Kinetico Quad Ring Kit
Now including the special Silicone O ring set - Very
difficult to obtain normally
The kit comprises:
Control Valve Quad Ring Seals
Purge Valve Quad Ring Seals
Drain Valve Piston Quad Ring Seals
Drain Valve Internal Piston Quad Ring Seals
Outlet Valve Piston Quad Ring Seals
Outlet Valve Internal Piston Quad Ring Seals
Actuator O ring seals
Balance piston internal O rings seals
In the United Kingdom a typical service for a Kinetico twin
tank design is now upwards of £350.00 + any parts used ( $450
Dollars) + Parts - A hugely Expensive Service Fee.
Our Video Teachings and "Low Cost" Seal Kits can save you a
lot of money.
We believe that the detailed Video product and full detailed
instructions; where you can follow the whole job for the full
life of your softener, together with the complete special and
precision parts service kit represents super value for
money.
And also let us be very clear, you would likely only need to
replace the seal kit once in your softeners lifetime.
But, the super Video Tutorials can be used again and again
for regular service intervals.
This really is a special deal.
Now we include the important seals within the Kinetico Softener
Head.
Shipping Now Worldwide
Brand New & Updated Videos and Seal Kits Included in this
Auction
Ships From United Kingdom - 7/10 Days Approx Shipping
Time
⭐⭐ Videos and Low Cost Kinetico Softener Parts⭐⭐
⭐⭐ NEW - Now With Lifetime Technical Support ⭐⭐
⭐⭐ 1000's VIDEOS SOLD - SEAL KITS INCLUDED⭐⭐
Shipping Worldwide
Packaging May be Different to as Shown
|
