Application
Package Include
♥【Material Improvement】PU Bushing is applied instead of rubber bushing, more suitable for low temperatures. Ball Pin is made of heat-treated alloy steel, which is more durable. A Protective Cover to prevent sediment from entering the ball head and prolong its service life. More Professional of the ball joint design, needn't add the grease additional.
♥【High Quality】Made of heat-treated carbon steel to increase the hardness and strength. Power coating surface has better wear resistance and corrosion resistance than paint, and is more suitable for outdoor environment. Reduces corrosion and abrasion by allowing new lubricant to flush contaminants.
♥【Advantage】The zerk with thread design is more convenient when adding grease. The Ball Head Design is more professional, without additional grease. The threaded nozzle is more convenient for adding grease.
♥【Special Notice about the wheels and Wires】Theses Control Arms will Fit the Factory Wheels and Tires and Wheels 17"or Large with 5" of Backspace with 33" by 12.50 tires. 34" 35" Might Rub Depends on Offset.
Installation
It is Easy to Direct Replace, but Professional Installation is Highly Recommended.
(1）Do Not require extra grease.
(2) Hexagon design for easier removal.
(3) Do Not screw too tight.
Measuring Guide
✱ Measure your stock front and rear heights from the ground to bottom of the trim. The style of level or lift will determine how much height you will need to add to the front or rear. To level your vehicle, add a lift amount equivalent to the difference between front and rear heights.
✱ To lift your vehicle - while retaining the stock look, add the same lift amount to both front and rear.
✱ To level lift your vehicle, add the amount of lift you'd like for the front to the difference between front and rear stock heights and use this for your rear lift.
Important Notice
— If you have any questions during the installation,plz don't be worry about
it.Be sure to finish the last step--move the jack from the car
— All the zerks can fill in grease after some use (pre-greased when you get it)
— Do not torque the zerk too tight and It can turns to different directions(not must vertical)---the right and left zerks no need to the same directions.
GMC Yukon 2007-2015 6-Lug 2WD 4WD
GMC Yukon XL 2007-2015 6-Lug 2WD 4WD
Chevy Avalanche 2007-2015 6-Lug 2WD 4WD
Chevy Suburban 1500 2007-2015 6-Lug 2WD 4WD
Chevy Tahoe 2007-2015 6-Lug 2WD 4WD
Cadillac Escalade 2007-2015 2WD 4WD
GMC Yukon XL 2007-2015 6-Lug 2WD 4WD
Chevy Avalanche 2007-2015 6-Lug 2WD 4WD
Chevy Suburban 1500 2007-2015 6-Lug 2WD 4WD
Chevy Tahoe 2007-2015 6-Lug 2WD 4WD
Cadillac Escalade 2007-2015 2WD 4WD
Specification
Conditon: Brand New
Material: Steel+Iron+Rubber
Material: Steel+Iron+Rubber
Type: Control Arm Kit
Items Included: Control Arm Kit, Bushing, Hardware
Placement on Vehicle: Front, Left, Right, Upper, Lower
Placement on Vehicle: Front, Left, Right, Upper, Lower
Fitment Type: Direct Replacement
Color: Red (as pictures show)
Suspension Grade: Heavy Duty
Replace Part Number: K80669 (Left) , K80670 (Right)
Mounting Style: Screw-On
Work For: 2-4" lift in the front
Suspension Grade: Heavy Duty
Features: Adjustable, Easy to Replace, Heavy Duty
Manufacturer Warranty: Five Years
Package Include
2Pcs x Heavy Duty Front Upper Control Arms
Features
♥ 【Professional Design】Our upper control arms are specially designed for improving strength, adding suspension travel and elimination of ball joint binding on leveled and lifted vehicles. They perfectly replace the OEM control arms, lift the vehicle 2”- 4”. Usually, when you lift 2’’ or more of your truck, OEM control arm would limit suspension travel, which will impact the driving performance. Our upper control arms will solve the problem and bring a more superior off-road performance.
♥ 【Professional Design】Our upper control arms are specially designed for improving strength, adding suspension travel and elimination of ball joint binding on leveled and lifted vehicles. They perfectly replace the OEM control arms, lift the vehicle 2”- 4”. Usually, when you lift 2’’ or more of your truck, OEM control arm would limit suspension travel, which will impact the driving performance. Our upper control arms will solve the problem and bring a more superior off-road performance.
♥【Material Improvement】PU Bushing is applied instead of rubber bushing, more suitable for low temperatures. Ball Pin is made of heat-treated alloy steel, which is more durable. A Protective Cover to prevent sediment from entering the ball head and prolong its service life. More Professional of the ball joint design, needn't add the grease additional.
♥【High Quality】Made of heat-treated carbon steel to increase the hardness and strength. Power coating surface has better wear resistance and corrosion resistance than paint, and is more suitable for outdoor environment. Reduces corrosion and abrasion by allowing new lubricant to flush contaminants.
♥【Advantage】The zerk with thread design is more convenient when adding grease. The Ball Head Design is more professional, without additional grease. The threaded nozzle is more convenient for adding grease.
♥【Special Notice about the wheels and Wires】Theses Control Arms will Fit the Factory Wheels and Tires and Wheels 17"or Large with 5" of Backspace with 33" by 12.50 tires. 34" 35" Might Rub Depends on Offset.
Installation
It is Easy to Direct Replace, but Professional Installation is Highly Recommended.
(1）Do Not require extra grease.
(2) Hexagon design for easier removal.
(3) Do Not screw too tight.
Measuring Guide
✱ Measure your stock front and rear heights from the ground to bottom of the trim. The style of level or lift will determine how much height you will need to add to the front or rear. To level your vehicle, add a lift amount equivalent to the difference between front and rear heights.
✱ To lift your vehicle - while retaining the stock look, add the same lift amount to both front and rear.
✱ To level lift your vehicle, add the amount of lift you'd like for the front to the difference between front and rear stock heights and use this for your rear lift.
Important Notice
— If you have any questions during the installation,plz don't be worry about
it.Be sure to finish the last step--move the jack from the car— All the zerks can fill in grease after some use (pre-greased when you get it)
— Do not torque the zerk too tight and It can turns to different directions(not must vertical)---the right and left zerks no need to the same directions.
Contact US
Please Check and Confirm the Item Can Fit Yours Before Buying.
Any Further Information, Please Feel Free to Contact Us.
Application
Package Include
♥【Material Improvement】PU Bushing is applied instead of rubber bushing, more suitable for low temperatures. Ball Pin is made of heat-treated alloy steel, which is more durable. A Protective Cover to prevent sediment from entering the ball head and prolong its service life. More Professional of the ball joint design, needn't add the grease additional.
♥【High Quality】Made of heat-treated carbon steel to increase the hardness and strength. Power coating surface has better wear resistance and corrosion resistance than paint, and is more suitable for outdoor environment. Reduces corrosion and abrasion by allowing new lubricant to flush contaminants.
♥【Advantage】The zerk with thread design is more convenient when adding grease. The Ball Head Design is more professional, without additional grease. The threaded nozzle is more convenient for adding grease.
♥【Special Notice about the wheels and Wires】Theses Control Arms will Fit the Factory Wheels and Tires and Wheels 17"or Large with 5" of Backspace with 33" by 12.50 tires. 34" 35" Might Rub Depends on Offset.
Installation
It is Easy to Direct Replace, but Professional Installation is Highly Recommended.
(1）Do Not require extra grease.
(2) Hexagon design for easier removal.
(3) Do Not screw too tight.
Measuring Guide
✱ Measure your stock front and rear heights from the ground to bottom of the trim. The style of level or lift will determine how much height you will need to add to the front or rear. To level your vehicle, add a lift amount equivalent to the difference between front and rear heights.
✱ To lift your vehicle - while retaining the stock look, add the same lift amount to both front and rear.
✱ To level lift your vehicle, add the amount of lift you'd like for the front to the difference between front and rear stock heights and use this for your rear lift.
Important Notice
— If you have any questions during the installation,plz don't be worry aboutit.Be sure to finish the last step--move the jack from the car
— All the zerks can fill in grease after some use (pre-greased when you get it)
— Do not torque the zerk too tight and It can turns to different directions(not must vertical)---the right and left zerks no need to the same directions.
GMC Yukon 2007-2015 6-Lug 2WD 4WD
GMC Yukon XL 2007-2015 6-Lug 2WD 4WD
Chevy Avalanche 2007-2015 6-Lug 2WD 4WD
Chevy Suburban 1500 2007-2015 6-Lug 2WD 4WD
Chevy Tahoe 2007-2015 6-Lug 2WD 4WD
Cadillac Escalade 2007-2015 2WD 4WD
GMC Yukon XL 2007-2015 6-Lug 2WD 4WD
Chevy Avalanche 2007-2015 6-Lug 2WD 4WD
Chevy Suburban 1500 2007-2015 6-Lug 2WD 4WD
Chevy Tahoe 2007-2015 6-Lug 2WD 4WD
Cadillac Escalade 2007-2015 2WD 4WD
Specification
Conditon: Brand New
Material: Steel+Iron+Rubber
Material: Steel+Iron+Rubber
Type: Control Arm Kit
Items Included: Control Arm Kit, Bushing, Hardware
Placement on Vehicle: Front, Left, Right, Upper, Lower
Placement on Vehicle: Front, Left, Right, Upper, Lower
Fitment Type: Direct Replacement
Color: Red (as pictures show)
Suspension Grade: Heavy Duty
Replace Part Number: K80669 (Left) , K80670 (Right)
Mounting Style: Screw-On
Work For: 2-4" lift in the front
Suspension Grade: Heavy Duty
Features: Adjustable, Easy to Replace, Heavy Duty
Manufacturer Warranty: Five Years
Package Include
2Pcs x Heavy Duty Front Upper Control Arms
Features
♥ 【Professional Design】Our upper control arms are specially designed for improving strength, adding suspension travel and elimination of ball joint binding on leveled and lifted vehicles. They perfectly replace the OEM control arms, lift the vehicle 2”- 4”. Usually, when you lift 2’’ or more of your truck, OEM control arm would limit suspension travel, which will impact the driving performance. Our upper control arms will solve the problem and bring a more superior off-road performance.
♥ 【Professional Design】Our upper control arms are specially designed for improving strength, adding suspension travel and elimination of ball joint binding on leveled and lifted vehicles. They perfectly replace the OEM control arms, lift the vehicle 2”- 4”. Usually, when you lift 2’’ or more of your truck, OEM control arm would limit suspension travel, which will impact the driving performance. Our upper control arms will solve the problem and bring a more superior off-road performance.
♥【Material Improvement】PU Bushing is applied instead of rubber bushing, more suitable for low temperatures. Ball Pin is made of heat-treated alloy steel, which is more durable. A Protective Cover to prevent sediment from entering the ball head and prolong its service life. More Professional of the ball joint design, needn't add the grease additional.
♥【High Quality】Made of heat-treated carbon steel to increase the hardness and strength. Power coating surface has better wear resistance and corrosion resistance than paint, and is more suitable for outdoor environment. Reduces corrosion and abrasion by allowing new lubricant to flush contaminants.
♥【Advantage】The zerk with thread design is more convenient when adding grease. The Ball Head Design is more professional, without additional grease. The threaded nozzle is more convenient for adding grease.
♥【Special Notice about the wheels and Wires】Theses Control Arms will Fit the Factory Wheels and Tires and Wheels 17"or Large with 5" of Backspace with 33" by 12.50 tires. 34" 35" Might Rub Depends on Offset.
Installation
It is Easy to Direct Replace, but Professional Installation is Highly Recommended.
(1）Do Not require extra grease.
(2) Hexagon design for easier removal.
(3) Do Not screw too tight.
Measuring Guide
✱ Measure your stock front and rear heights from the ground to bottom of the trim. The style of level or lift will determine how much height you will need to add to the front or rear. To level your vehicle, add a lift amount equivalent to the difference between front and rear heights.
✱ To lift your vehicle - while retaining the stock look, add the same lift amount to both front and rear.
✱ To level lift your vehicle, add the amount of lift you'd like for the front to the difference between front and rear stock heights and use this for your rear lift.
Important Notice
— If you have any questions during the installation,plz don't be worry about
it.Be sure to finish the last step--move the jack from the car— All the zerks can fill in grease after some use (pre-greased when you get it)
— Do not torque the zerk too tight and It can turns to different directions(not must vertical)---the right and left zerks no need to the same directions.
Contact US
Please Check and Confirm the Item Can Fit Yours Before Buying.
Any Further Information, Please Feel Free to Contact Us.
On Mar 4, 2024 at 19:31:12 PST, seller added the following information: