|
REPLACING THE THROTTLE BODY ASSEMBLY
Under some circumstances, it might be necessary to remove the throttle body
assembly. Sometimes it may be to thoroughly clean the inlet and throttle blade,
but more often it will be to replace it. The procedure is pretty straightforward.
Q: How to tell if you need a new throttle body?
A: If you find that your car idles quicker than usual, that may mean that the throttle body is sticking open. If your check engine light comes on and you find that you can’t get the car to accelerate above a certain rpm, the ECU has put you in limp mode. This means that there is something wrong with the drive-by-wire system. The most dangerous indicator is if the throttle sticks while driving and you can’t get the car to stop accelerating. If that ever happens, put the car in neutral and turn the key back one click and coast to the side of the road.
REMOVAL
1. Disconnect the ground cable from battery.
2. Lift up the vehicle. Remove the under cover.
3. Remove the clip (A), and loosen the clamps (B) and (C) securing the air intake boot.
4. Remove the air intake boot from the air cleaner case (rear) and throttle body, and move the air intake boot aside so that it does not interfere with the work.
5. Disconnect the connectors (A) from the throttle position sensor.
6. Disconnect the preheater hose (B) from the throttle body.
7. Remove the throttle body from the intake manifold.
INSTALLATION
Install in the reverse order of removal.
NOTE:
Before installing the new assembly, inspect the intake-manifold-to-throttle-body gasket for damage. If it is damaged, it must be replaced.
If it is in good condition, it can be reused.
WARNING:
DO NOT place fingers in or around the throttle body plate. If the throttle body is energized, the throttle plate could move causing personal injury. Always disconnect the negative battery cable prior to servicing the throttle body.
CAUTION:
DO NOT move the throttle plate while power is connected to the throttle body. This may cause fault codes to set.
Q: Is there anything that has to be done after installing the replacement throttle body?
A: A relearn calibration procedure is necessary after installation of replacement throttle body
Q: What is throttle body relearn?
A: Idle Relearn (aka throttle body relearn) is the procedure that is required to obtain the correct idle speed after replacing electronic throttle body, disconnecting a battery cable, clearing a check engine light, etc.
Relearn A MECHANICALLY CONTROLLED THROTTLE BODY
1. Remove terminals from the battery for 15 minutes.
2. Start the engine. Let it idle for 10 minutes. Remember not to switch on any additional consumers.
3. Stop the engine for about 10 seconds. Start it again.
4. Wait until the power unit warms up to the operating temperature. After that, you can start using the vehicle.
Take notice: you might need to drive 150–200 km until the idling stabilises.
Relearn AN ELECTRONICALLY CONTROLLED THROTTLE BODY
The readjustment process might vary in different vehicles. Therefore, before you start the procedure, consult the vehicle manual for the exact step sequence.
The general algorithm is as follows:
1. Study procedure and try to remember it. You’ll have to act quickly so you won’t have time to check the details.
2. Start the engine. Warm it up to the working temperature.Stop it for 10 seconds.
3. Switch on the ignition for 3 seconds.
4. Press the accelerator pedal quickly for 5 times. One depression should take one second.
5. Press the gas pedal to the floor for 7 seconds. Keep it depressed until the “Check Engine” light burns steady and hold it for 3 more seconds.
6. Press the gas pedal to the floor for 7 seconds. Keep it depressed until the “Check Engine” light burns steady and hold it for 3 more seconds.
7. Release the gas pedal and start the engine.
Q: HOW TO PREVENT THE THROTTLE BODY FROM GETTING DIRTY?
A: 1. Use only high-quality fuel. Otherwise, impurities and contaminants will get inside the engine causing the rapid formation of carbon deposits on the throttle body. For the same reason, you shouldn’t neglect the fuel filter replacement. It is recommended to flush the fuel tank from time to time.
2. Replace the air filter on time. Always make sure that the intake system is air-tight. This simple check prevents unfiltered air from being sucked into the intake system in places where its components are not connected tightly.
3. Always make sure that the crankcase ventilation system is fault-free. Its malfunctions cause a fast formation of oily deposits on elements of the throttle body.
Fits the Following Vehicles:
1990-1993 Acura Integra GS L4.1834cc
1997-2001 Acura Integra GS L4.1834cc
1992-1993 Acura Integra GS-R L4.1678cc
1994-2001 Acura Integra GS-R L4.1797cc
1986-1989 Acura Integra LS L4.1590cc
1990-2001 Acura Integra LS L4.1834cc
1987-1988 Acura Integra LS Spec Ed L4.1590cc
1986-1989 Acura Integra RS L4.1590cc
1990-1998 Acura Integra RS L4.1834cc
1995-1996 Acura Integra Spec Ed L4.1834cc
1997-1998 Acura Integra Type R L4.1797cc
2000-2001 Acura Integra Type R L4.1797cc
1992-2000 Honda Civic EX L4.1590cc
2001 Honda Civic EX L4.1668cc
1992-1995 Honda Civic Si L4.1590cc
1999-2000 Honda Civic Si L4.1595cc
1997-2001 Honda Prelude Base L4.2156cc
1992-1996 Honda Prelude S L4.2156cc
1995 Honda Prelude SE L4.2259cc
1992-1996 Honda Prelude Si L4.2259cc
1992-1994 Honda Prelude Si 4WS L4.2259cc
1997-2001 Honda Prelude Type SH L4.2156cc
1993-1996 Honda Prelude VTEC L4.2156cc
2000-2003 Honda S2000 Base L4.1997cc
2004-2009 Honda S2000 Base L4.2157cc
2008-2009 Honda S2000 CR L4.2157cc
by-wire throttle bodies only
Payments are expected within 7 days after the last winning auction is closed; Otherwise Unpaid Item Dispute will be filed with eBay.
Product will be shipped within 2 business days after full payment is received and verified. Delivery Time is about 3-7 business days to most of countries.
All domestic orders will be shipped via USPS, UPS or FedEx from our US warehouse and usually arrives to your door in about 3-5 business days.
We ship the package to your shipping address in eBay instead of the one in PayPal. Please tell us your shipping address if it is different from the one in eBay.
The tracking number will be given for the customer to check the shipping status online (registered or faster service only).
We are not responsible for any wrong or undeliverable addresses. Please verify and update your shipping address on eBay during checkout.
Refunds will be credited within 2 or 3 business days after returned item(s) is received.
2.If you are satisfied with the product you received, please leave us positive feedback and 5 scores DSR
1,We will leave positive feedback once we get your payment
Shop Category Picture Hot Item Picture Help & Info Payment Policy Shipping Policy Return Policy FAQ About Us |
70mm Throttle Body w/Sensor For Honda Civic Si Crx Acura Integras Gsr BD New
REPLACING THE THROTTLE BODY ASSEMBLY Under some circumstances, it might be necessary to remove the throttle body assembly. Sometimes it may be to thoroughly clean the inlet and throttle blade, but more often it will be to replace it. The procedure is pretty straightforward.
Q: How to tell if you need a new throttle body? A: If you find that your car idles quicker than usual, that may mean that the throttle body is sticking open. If your check engine light comes on and you find that you can’t get the car to accelerate above a certain rpm, the ECU has put you in limp mode. This means that there is something wrong with the drive-by-wire system. The most dangerous indicator is if the throttle sticks while driving and you can’t get the car to stop accelerating. If that ever happens, put the car in neutral and turn the key back one click and coast to the side of the road.
REMOVAL 1. Disconnect the ground cable from battery. 2. Lift up the vehicle. Remove the under cover. 3. Remove the clip (A), and loosen the clamps (B) and (C) securing the air intake boot. 4. Remove the air intake boot from the air cleaner case (rear) and throttle body, and move the air intake boot aside so that it does not interfere with the work. 5. Disconnect the connectors (A) from the throttle position sensor. 6. Disconnect the preheater hose (B) from the throttle body. 7. Remove the throttle body from the intake manifold. INSTALLATION Install in the reverse order of removal.
NOTE: Before installing the new assembly, inspect the intake-manifold-to-throttle-body gasket for damage. If it is damaged, it must be replaced. If it is in good condition, it can be reused.
WARNING: DO NOT place fingers in or around the throttle body plate. If the throttle body is energized, the throttle plate could move causing personal injury. Always disconnect the negative battery cable prior to servicing the throttle body.
CAUTION: DO NOT move the throttle plate while power is connected to the throttle body. This may cause fault codes to set.
Q: Is there anything that has to be done after installing the replacement throttle body? A: A relearn calibration procedure is necessary after installation of replacement throttle body
Q: What is throttle body relearn? A: Idle Relearn (aka throttle body relearn) is the procedure that is required to obtain the correct idle speed after replacing electronic throttle body, disconnecting a battery cable, clearing a check engine light, etc.
Relearn A MECHANICALLY CONTROLLED THROTTLE BODY 1. Remove terminals from the battery for 15 minutes. 2. Start the engine. Let it idle for 10 minutes. Remember not to switch on any additional consumers. 3. Stop the engine for about 10 seconds. Start it again. 4. Wait until the power unit warms up to the operating temperature. After that, you can start using the vehicle. Take notice: you might need to drive 150–200 km until the idling stabilises.
Relearn AN ELECTRONICALLY CONTROLLED THROTTLE BODY The readjustment process might vary in different vehicles. Therefore, before you start the procedure, consult the vehicle manual for the exact step sequence.
The general algorithm is as follows: 1. Study procedure and try to remember it. You’ll have to act quickly so you won’t have time to check the details. 2. Start the engine. Warm it up to the working temperature.Stop it for 10 seconds. 3. Switch on the ignition for 3 seconds. 4. Press the accelerator pedal quickly for 5 times. One depression should take one second. 5. Press the gas pedal to the floor for 7 seconds. Keep it depressed until the “Check Engine” light burns steady and hold it for 3 more seconds. 6. Press the gas pedal to the floor for 7 seconds. Keep it depressed until the “Check Engine” light burns steady and hold it for 3 more seconds. 7. Release the gas pedal and start the engine.
Q: HOW TO PREVENT THE THROTTLE BODY FROM GETTING DIRTY? A: 1. Use only high-quality fuel. Otherwise, impurities and contaminants will get inside the engine causing the rapid formation of carbon deposits on the throttle body. For the same reason, you shouldn’t neglect the fuel filter replacement. It is recommended to flush the fuel tank from time to time. 2. Replace the air filter on time. Always make sure that the intake system is air-tight. This simple check prevents unfiltered air from being sucked into the intake system in places where its components are not connected tightly. 3. Always make sure that the crankcase ventilation system is fault-free. Its malfunctions cause a fast formation of oily deposits on elements of the throttle body.
Fits the Following Vehicles: 1990-1993 Acura Integra GS L4.1834cc 1992-2000 Honda Civic EX L4.1590cc 1992-1995 Honda Civic Si L4.1590cc 1997-2001 Honda Prelude Base L4.2156cc 2000-2003 Honda S2000 Base L4.1997cc by-wire throttle bodies only Payment
Payments are expected within 7 days after the last winning auction is closed; Otherwise Unpaid Item Dispute will be filed with eBay. Shipping
Product will be shipped within 2 business days after full payment is received and verified. Delivery Time is about 3-7 business days to most of countries. All domestic orders will be shipped via USPS, UPS or FedEx from our US warehouse and usually arrives to your door in about 3-5 business days. We ship the package to your shipping address in eBay instead of the one in PayPal. Please tell us your shipping address if it is different from the one in eBay. The tracking number will be given for the customer to check the shipping status online (registered or faster service only). We are not responsible for any wrong or undeliverable addresses. Please verify and update your shipping address on eBay during checkout. Returns
Refunds will be credited within 2 or 3 business days after returned item(s) is received. Contact Us
2.If you are satisfied with the product you received, please leave us positive feedback and 5 scores DSR Feedback
1,We will leave positive feedback once we get your payment All rights reserved. |