LAUNCH X431 TSGUN TPMS Tire pressure Diagnostic Tools, Active 315MHz & 433MHz sensors , Read & Write Sensor ID , TPMS Programming and Learning , Read & Clear Tire Pressure Fault, Support work with x431 V/V+/X431 PRO3/X431 PRO3S /PAD V / PAD VIII
The first TPMS tool work with LAUNCH diagnostic tool
X-431 TSGUN is a professional TPMS diagnostic tool that integrates TPMS sensor activation, reading, learning and programming. It can activate and read tire pressure sensor information through high or low radio frequency
The X-431 TSGUN tire pressure gun is portable, powerful and easy to operate. It needs to work with LAUNCH intelligent diagnostic tool to perform the tire pressure activation, programming, diagnosis and learning functions.
Support Sensor Activation:
LAUNCH X431 TSGUN can activate all 315MHz/433MHz tire pressure sensors, and can read, copy, write sensor IDs and read tire pressure data (pressure, temperature, battery status)
Support Sensor Programming：
This function allows users to program the sensor data to the L AUNCH-sensor and replace faulty sensor with low battery life or one that is not functioning.
There are three options available for programming LAUNCH-sensor:Auto Create, Manual Create and Copy by Activation.
(Note: Do not place the device close to several sensors at the same time, or the diagnostic tool will detect more sensors, which may result in programming failure)
Method 1 - Auto Create
When the original sensor ID cannot be obtained, this function can be used to program the LAUNCH sensor according to the ID randomly created by the test vehicle.
Method 2 - Manual Create
When the original sensor ID cannot be obtained, this function can be used to program the LAUNCH sensor according to the ID randomly created by the test vehicle.
Method 3 - Copy By Activation
By first activating the original sensor data, and then copying the activated sensor data into the LAUNCH sensor. Before using this method, the original sensor data must be activated.
Support Sensor Learning
The user can use this function to write the newly programmed sensor ID into the vehicle ECU for sensor identification. Only when the newly programmed sensor ID is different from the original sensor ID stored in the vehicle ECU, the re-learning operation is required.
There are three ways available for Relearn: Static Learning, Self- Learning and Relearn by OBD.
Method 1 - Static Learning
Static learning needs to put the vehicle in "learning mode", and then follow the learning steps prompted on the screen.
Method 2 - Self-Learning
For some vehicles, the learning function can be completed by driving the vehicle self-learning.
Method 3- Relearn by OBD
This function allows the diagnostic tool to write the sensor ID to the TPMS module.
To perform the OBD re-learning function, first use the tire pressure tool to activate all four tire sensors. Then use the diagnostic equipment and its attached diagnostic connector, and follow the on-screen instructions to complete the re-learning operation.
Diagnose tire pressure fault
Read and clear the fault code of the TPMS system
Support more than 115+ brands
For OBDII diagnostics, the obd2 code reader works great for most cars built in 1996 or later, being compatible with following protocols:
-ISO 14230-4 (KWP2000)
-ISO 15765-4 (CAN)
-ISO 9141-2 (iso)
-ISO 14229 (uds)
-SAE J1850 (VPW & PWM)
-Original protocols of makers
For advanced functions as active test, all system diagnostics, and maintenance service, it covers 95% of car models available in the market including:
-Asia:
for Daewoo, for Honda, for JP Isuzu, for Kia, for Mazda, for Mitsubishi, for Nissan, for SGM, for Subaru, for Suzuki, for Toyota,for Hyundai, for Ssangyong
-Europe:
for Aston Martin, for Audi, for Benz, for BMW, for Citroen, for Ferrari, for Fiat, for Land Rover, for Maserati, for Opel, for Porsche, for Renault, for Rover, for Saab, for Seat, for Skoda, for Smart, for Sprinter, for Volvo, for VW, for Peugeot
-America:
for Chrysler, for USA-Ford, for GM
And keep updating.
How to use?
For initial use, user needs to bind the X-431 TSGUN to the diagnostic tool,
1. Tap TPMS on the Job menu of the diagnostic tool.
2. Tap Bind X-431 TSGUN to enter.
3. Tap Bind, the binding interface will pop up.
4. Enter the required information. After inputting, tap Bind. It will be displayed in the Bound list automatically .
( Repeat steps 3~4 to bind multiple X-431 TSGUN devices to the diagnostic tool.）
Does LAUNCH X431 TSGUN work directly ?
No , X431 TSGUN need works with LAUNCH X431 Device as following :
X431 Serial : X431 V ,X431 V+, ect
Pro Series: X431 PRO/ X431 PRO3/ X431 PRO5/X431 PRO3S+
PAD Series: X431 PAD III / X431 PAD V
....
More products will be covered to support this feature.
(Note:TSGUN only support work with X431 Serial product which size over 8 inch , can not work with Diagun V and X431 Pro mini )
Packing List :
1* X-431 TSGUN
1* USB cable
1* box
