Thank you for viewing this item, why not visit my eBay shop for loads more woodturning and general woodworking tools and finishes, if you click on categories when there it will make finding items easier. I combine postage where I can, so either place your order as normal and I’ll refund what I can, or select ‘request total from seller’ and I’ll send you a total cost invoice.
Please note, Accelerator CANNOT be shipped overseas.
Gorilla Glues.
Gorilla Wood Glue is a non-toxic water based, solvent free polyvinyl acetate (PVA) glue that requires only 20-30mins clamp time and is fully cured in 24 hours.
It is suitable for use indoors and outdoors and can be used on hardwoods, softwoods and wood composites. This glue dries with a natural finish.
The GRGGWG536 Gorilla Wood Glue comes in the following:
Size 536ml.
Gorilla Glue is a polyurethane glue. When exposed to moisture, the adhesive reacts and creates a foaming action that fills whilst it sticks. Gorilla Glue has an open working time of 20 minutes. The glue is brown in colour, but dries a tan colour, and is totally waterproof. Gorilla Glue is incredibly strong, bonding all types of wood, including pressure treated wood. It also bonds stone, metal, ceramics, foam, glass, leather and more. Once dried the product is sandable, stainable, paintable and can also take a varnish. Due to its foaming action the glue gives greater coverage - up to 3 times the coverage of other glues. This glue is unaffected by extreme hot and cold and will not break down when exposed to rain and snow.
The Gorilla Glue formula bonds materials that typical all-purpose adhesives will not hold, including wood, stone, metal ceramics, glass, foam and even bonds dissimilar materials. It is waterproof and temperature resistant, which means it can be used for indoor and outdoor projects and repairs.
Originally used as a commercial adhesive for hard-to-glue materials. Once something is glued it will not come undone - it is set to survive years after the repair.
The GRGGG250 Gorilla glue comes in the following:
Size: 250ml
Chestnut CA Glues.
When you want to bond two surfaces together quickly and efficiently there’s nothing much that beats a cyanoacrylate superglue.
Chestnut Products’ CA Superglues come in three viscosities:
- Thin – very low viscosity for capillary action when you want the glue to penetrate deep into small cracks. Can also be used to post-assembly to wick into parts.
Ideal for use when joining very close fitting parts and smooth, even surfaces. Dries in seconds. - Medium – for general purpose use, stays where you put it! Takes up to 20 seconds to dry giving you enough time to line everything up. Good for fairly smooth surfaces.
- Thick – for gap filling where you want to seal a crack in your timber, mixed with sawdust if you want.
Slower drying, up to 60 seconds when applied thickly.
If you need a faster drying time use Accelerator for Superglues which can reduce the drying time to less than 2 seconds. Use the accelerator sparingly to avoid a white bloom on the surface. Accelerator cannot be shipped overseas.
A full cure – and maximum strength – requires 24 hours.
Low temperatures can reduce the cure time.
To get the longest life out of your glue, keep away from warmth – they are best stored at +5 degrees C.
Black CA Glue.
A new take on our CA Superglue, this is a thick, black glue with all the same properties but ideal for use when the glue line shows. The dried glue imitates the look of a natural flaw in the timber, disguising the join so that it becomes a feature!
Available in 20g bottles.
CA Debonder.
Accidents will happen, whether you’ve misaligned something you’ve stuck together with superglue or you’ve stuck your hand to the desk!
DeBonder will dissolve superglue to allow the bond to be broken should you need to. You can also use it to clean up uncured spills of glue and remove small areas of cured glue. Over time it will soften larger areas to make cleaning up easier.
It will debond skin but should not be used on lips or eyes.
DeBonder comes in a small glass jar which has a useful applicator in the lid.
Chestnut CA Accelerator.
Cyanoacrylate Superglues are pretty fast drying already, especially the thin one. But sometimes when you’re gap filling or just in a hurry you want a quicker or even an instant bond, and that’s where our Accelerator for Superglues come in, supplied in an easy to use aerosol.
You can use this in one of two ways. If you’re gap filling and the glue is exposed a quick spray with the Accelerator will force the glue to dry straight away. Don’t use too much, this can cause the glue to cloud and go white.
If you’re working on an enclosed joint and can’t spray onto the glue, instead apply the glue to one side of the joint and spray accelerator on the other side, join and it’s stuck. And we mean stuck, so make sure you get it right, you probably won’t have any time to reposition it if you need to.
Everbuild HV Superglue 20g
Everbuild Industrial Superglue HV is a high viscosity flash setting industrial adhesive based on advanced cyanoacrylate technology. It can fill gaps up to 0.25mm and is 100% solvent free. Can be used on MDF, rubber, metals, PVCu and plastics.
Can be used with activator to speed up & increase adhesion.
Viscosity at: 25°C - 1500 cps.
Set time: 10 to 30 seconds.