Premium 16-Way CATV RF Active Splitter Combiner With Amplifier
This CATV RF splitter is a premium active type 1Ghz RF signal splitter for private cable
TV, antenna, analog/digital broadcast TV or MATV employing multiple modulators and other RF coax equipment.
It can split a RF or TV source signal for 16 TVs or cable boxes and retain the same signal level with high isolation.
A powered 20-dB amplifier bundled in the package for splitter mode use, Ideal for CATV, surveillance CCTV, antenna TV operations.
This splitter can also be used in a reverse way as a 16 in 1 out RF CATV combiner with no external power supply needed for the operation.
 |
True Lossless Active Type 16-Way RF CATV Splitter
This RF coax TV video splitter can provide 16
simultaneous amplified outputs with minimum loss through the bundled external
amplifier.
This active type splitter includes a 20-dB amplifier so every one of the 16 RF outputs can carry and retain the same signal level as the original RF input.
 |
Long Range Extension With 20dB Boost
This 16-way RF splitter is bundled with a powered RF amplifier with 20 dB boost for RF
input signals to be distributed over the long cable run.
Users can easily extend the cable TV or UHF/VHF RF TV signal for another 1000FT or 300m if the RF source signals have fair 70 to 75dB strength to start with.
So more TVs, TV tuners or set top boxes can be added in office building or residence through this splitter combined with amplifier.
 |
 |
Wide Frequency Range Support
This unit supports a broad frequency range from 5 to 1000MHz. Most of the RF TV signals such as cable TV or antenna TV signals can be handled by this
unit.
 |
16 In 1 Out RF CATV Combiner
This splitter can also be used in a reverse way as a 16 in 1 out RF CATV
combiner with no power supply needed.
It can combine RF coax signals from multiple and up to 16 sources into one coax cable run.
 |
High Isolation
This CATV combiner splitter provides high Port-To-Port isolation so each output can be transmitted in
stable quality with no noise or interference incurred.
1U Rack Mountable
This unit is built in 19" 1U size and rack mount ready for setup with other headend rack systems.
-20 dB Test Port
A front-panel -20 dB test port (75-ohm "F" type connector) allows testing of the unit's output without interrupting the
service and easy for troubleshooting.
 |
- Professional high-end 1 in 16 out digital/analog RF cable TV signal splitter.
- Top-grade 16 in 1 out RF coax TV signal combiner.
- Designed to divide/duplicate single RF input into 16 identical RF outputs with zero loss.
- Distribute TV signal to up to 16 locations or for 16 TVs and each RF splitted output will retain the same level.
- Ideal for CATV, surveillance CCTV, aerial TV and MATV coaxial operations.
- An external 20-dB amplifier included.
- Built with high Port-To-Port isolation between RF TV signals so each output can be transmitted in stable quality with no noise or interference incurred.
- Supports broadband frequency range of 5 to 1000MHz.
- 75-ohm impedance for all outputs provides the best possible signal.
- Die cast housing for absolute minimal losses.
- Standard 19" 1U size rack mountable.
- RF Input: 75 ohm, Coax F-Type Female x 1
- RF Outputs: 75 ohm, Coax F-Type Female x 16
- Frequency Range: 5~1000MHz
- Input Power: 75 dBuV
- Insertion Loss: typical 1dB
- Frequency Response: typical 2 dB
- Isolation out-to-out: typical 20 dB
- Return Loss-Input: 12~14dB, typical 13 dB
- Return Loss-Output: 10~12dB, typical 11 dB
- Noise Figure: typical 5 dB
- AC Power: 110V(60Hz) with US 2-Prong plug
- 16-way RF CATV splitter/combiner
- RF amplifier with 20dB gain for 110V AC power use
- User manual