Bandwidth

150MHz

100MHz

150MHz

100MHz

Oscilloscope channels

2CH

2CH

2CH

2CH

Waveform generator

1CH

1CH

-

-

Oscilloscope

Sample rate

1GSa/s (single channel) 500MSa/s (two channels)

Acquisition

Normal

Sample data

Peak-to-peak value

Display high frequency and random burr

Average

Average waveform, times:  4, 8, 16, 32, 64, 128

High resolution

Up to 12bit

Input

Input coupling

DC, AC, GND

Input impedance

1MΩ±2% ‖20pF±3pF

Probe attenuation  factor

1X, 10X, 100X, 1000X

Voltage rating

300V CAT II

Maximum input voltage

300VRMS (10X)

Horizontal

Waveform interpolation

(sin x)/x

Maximum record length

Single channel maximum 8M

Two channels maximum 4M

Horizontal scale range

2ns/div~100s/div  1, 2, 5 step by step

Time base mode

Y-T, X-Y, Roll

Zero offset

±0.5 div×minimum time base gear

Sample Rate and Delay Time Accuracy

±25ppm

Delta Time Measurement Accuracy (Full Bandwidth)Sample Rate and Delay Time Accuracy

single-shot, Normal mode   ±（1 sample interval+100ppm×reading+0.6ns）

＞16 times averages ±（1 sample interval+100ppm×reading+0.4ns）

Sample interval=sec/div÷200

Sample Rate and Delay Time Accuracy

±50ppm（at any interval greater than 1ms）

Vertical

Model

DSO2D15

DSO2D10

DSO2C15

DSO2C10

Bandwidth

150MHz

100MHz

150MHz

100MHz

Rising time in BNC position (typical)

2.4ns

3.5ns

2.4ns

3.5ns

Vertical resolution

8 bits resolution, each channel samples simultaneously

Vertical sensitivity

2mV/div to 10V/div

Offset range

≥200mV/div, ±1V;

＜200mV/div ±50V

Mathematical operation

+, -, ×, ÷, FFT

FFT

Window: Rectangle, Hanning, Hamming, Blackman, Bartlett, Flattop

Bandwidth Limit

20MHz

Bass response（-3db）

In BNC position ≤ 10Hz

Vertical gain accuracy

In ''normal''  or ''average'' acquisition mode, the accuracy of 10V/div to 10mV/div is ±3%;

In ''normal'' or ''average'' acquisition mode, the accuracy of 5mV/div to 2mV/div is ±4%

Note: Bandwidth reduced to 6MHz when using a 1X probe

Trigger

Trigger type

Edge, Pulse width, Video, Slope, Overtime, Window, Pattern, Interval, Under Amp, UART, LIN, CAN, SPI, IIC

Trigger level range

±5 divisions from the center of the screen

Trigger mode

Auto, Normal, single

Level

CH1~CH2

±4 divisions from the center of the screen

EXT(Only With AWG Model)

0~3.3V

Holdoff range

8ns~10s

Trigger level accuracy

CH1~CH2

0.2 div×volts/div within ±4 divisions from the center of the screen

EXT(Only With AWG Model)

±（Set value× 6%+40mV）

Edge trigger

Slope

Rising edge, falling edge, rising or falling edge

Signal source

CH1, CH2, EXT(Only With AWG Model)

Pulse width trigger

Polarity

Positive polarity, negative polarity

Condition(When)

<, >, !=, =

Signal source

CH1~CH2,

Pulse width range

8ns ~ 10s

Accuracy

8ns

Video trigger

Signal standard

NTSC, PAL

Signal source

CH1~CH2

Synchronization

Scanning line, line number, odd field, even field, all field

Slope trigger

Slope

rising, falling

Condition(When)

<, >, !=,  =

Signal source

CH1 ~ CH2

Time range

8ns ~ 10s

Accuracy

8ns

Overtime trigger

Signal source

CH1~CH2，

Polarity

Positive polarity, negative polarity

Time range

8ns ~ 10s

Accuracy

8ns

Window trigger

Signal source

CH1~CH2

Pattern trigger

Pattern

0: low level; 1: high level; X: ignore

Level（signal source）

CH1~CH2

Interval trigger

Slope

rising, falling

Condition(When)

<, >,  !=,  =

Signal source

CH1~CH2

Time range

8ns ~ 10s

Accuracy

8ns

Under Amp trigger

Polarity

Positive polarity, negative polarity

Condition(When)

<, >, !=, =

Signal source

CH1~CH2

Time range

8ns ~ 10s

Accuracy

8ns

UART trigger

Condition(When)

Start, Stop, data, Parity ERR, COM ERR

Signal source(RX/TX)

CH1~CH2

Data format

Hex (hexadecimal)

Data length

1 byte

Data bit width

5 bit, 6 bit, 7 bit, 8 bit

Odd-even check

none, odd, even

Idle level

high, low

Baud rate (optional)

110/300/600/1200/2400/4800/9600/14400/19200/38400/57600/115200/230400/380400/460400 bit/s

Baud rate(user-defined)

300bit/s~334000bit/s

LIN trigger

Condition(When)

Interval field, synchronization field, ID field, synchronization error, identifier, ID and data

Signal source

CH1~CH2

Data format

Hex (hexadecimal)

Baud rate (optional)

110/300/600/1200/2400/4800/9600/14400/19200/38400/57600/115200/230400/380400/460400 bit/s

Baud rate(user-defined)

300bit/s~334000bit/s

CAN trigger

Condition(When)

Start bit, remote frame ID, data frame ID, frame ID, data frame data, error frame, all errors, ACK Error, overload frame

Signal source

CH1~CH2

Data format

Hex (hexadecimal)

Baud rate (optional)

10000, 20000, 33300, 500000, 62500, 83300, 100000, 125000, 250000, 500000, 800000, 1000000

Baud rate(user-defined)

5kbit/s~1Mbit/s

SPI trigger

Signal source

CH1~CH2

Data format

Hex (hexadecimal)

Data bit width

4, 8, 16, 24, 32

IIC trigger

Signal source (SDA/SCL)

CH1~CH2

Data format

Hex (hexadecimal)

Data index

0~7

When(condition)

Start bit, stop bit, No Ack, address, restart, address and data

Measurement

Cursor

Voltage difference between cursors △V

Time difference between cursors △T

Reciprocal of △T, in Hertz (1/△T)

Auto measurement

frequency, period, mean, peak-to-peak, RMS, minimum, mixmum, rising time, falling time, + width, - width, base, top, middle, amplitude, overshoot, preshoot, rising edge phase difference, falling edge phase difference, + duty, - duty, period mean, PRMS, FOVshoot, ROVshoot, BWIDTH, FRF, FFR, LRR, LRF, LFR, LFF

DVM

Data source

CH1, CH2

Measurement type

DC RMS

AC RMS

DC

Frequency meter

hardware 6 bits frequency meter

Arbitrary waveform generator

Channel

1

Sample rate

200MSa/s

Vertical resolution

12 bits

Maximum frequency

25 MHz

Standard waveforms

sine, square, ramp,Exp, noise, DC

Arbitrary waveform

Arb1, Arb2, Arb3, Arb4

Sin

Frequency range

0.1Hz~25MHz

Square/pulse

Frequency range

0.1Hz~10MHz

Triangular wave

Frequency range

0.1Hz~1MHz

Sampling wave

Frequency range

0.1Hz~1MHz

Index

Frequency range

0.1Hz~5MHz

Noise

Arb1

Frequency range

0.1 Hz to 10 MHz

Arb2

Frequency range

0.1 Hz to 10 MHz

Arb3

Frequency range

0.1 Hz to 10 MHz

Arb4

Frequency range

0.1 Hz to 10 MHz

Waveform length

4KSa

Frequency

Accuracy

100 ppm (<10 kHz) 50 ppm (>10 kHz)

Resolution

0.1 Hz or 4 bits，take the greater one

Amplitude

Output range

10mV~7Vp-p (high impedance)

5mV~3.5Vp-p (50Ω)

DC offset

Range

±3.5 V, high impedance

±1.75 V, 50 Ω

Resolution

100 μV or 3 bits, take the greater one

Accuracy

2% (1 kHz)

Output impedance

50 Ω

General specifications

Display

Display type

7'' diagonal TFT liquid crystal

Display resolution

800 (horizontal)*480 (vertical) pixels

Display colour

16 million colours (24 bits true colour)

Persistence time

minimum, 1 s, 5 s, 10 s, 30 s, infinite

Display type

dot, vector

Display brightness

adjustable

Grid type

adjustable

Grid brightness

adjustable

Interface

Standard interface

USB Host，USB Device

General specifications

Probe compensator output

Output voltage, typical

about 2Vpp input ≥1MΩ load

Frequency, typical

1kHz

Power supply

100-120VACRMS(±10%), 45Hzto 440Hz, CATⅡ

120-240VACRMS(±10%), 45Hz to 66Hz, CATⅡ

Power consumption

<30W

Fuse

T, 3.15A, 250V, 5x20mm

Operating temperature

0~50 °C (32~122 °F)

Storage temperature

-40~+71 °C (-40~159.8 °F)

Humidity

≤+104℉(≤+40°C): ≤90% relative humidity

106℉~122℉ (+41°C ~50°C): ≤60% relative humidity

Altitude

Operating and nonoperating

3, 000m (10, 000 feet)

Mechanical shock

Random vibration

0.31 g RMS from 50Hz to 500Hz,

10 minutes on each axis

Nonoperating

2.46g RMS from 5Hz to 500Hz,

10 minutes on each axis

Operating

50g, 11ms, half-sine wave

Mechanical

Size

318 x 110 x 150mm (length x width x height)

Weight

1900g