Description
SIM900 Module GPRS Shield 4 Frequency Development Board GSM GPRS SMS Wireless Data TC35i for Arduino
Description:
The GPRS Shield is based on SIM900 module from SIMCOM and compatible with Arduino and its clones. The GPRS Shield provides you a way to communicate using the GSM cell phone network. The shield allows you to achieve SMS, MMS, GPRS and Audio via UART by sending AT commands (GSM 07.07 ,07.05 and SIMCOM enhanced AT Commands). The shield also has the 12 GPIOs, 2 PWMs and an ADC of the SIM900 module(They are all 2V8 logic) present onboard.
1. Provide 2 kinds of antenna interfaces, compatible with various needs. This product is shipped with an antenna, and the antenna has an extension cable, so it is compatible with 2 interfaces.
2. SIM900 can be set via jumper cap and connected to any 2 pins of Arduino from D0 to D7, not only the hardware UART of D0D1.
3. Debug toggle switch, you can set the DEBUG port of SIM900 to connect to Arduino or connect to PC through ATMEGA8U2 / FT232 on Arduino for debugging.
4. The audio and microphone ports are led out.
5. The multiple IO ports of SIM900 are led out. If necessary, you can use a Dupont cable to connect the pins-refer to the schematic diagram and datasheet for specific pins.
6. 3 status indicator lights, and 3 buttons-the power on button can be used to power on SIM900 by using the Arduino pin control to reach the software.
7. 3.3V and 5V automatic level compatible, it can adapt to 3.3V or 5V main control board, support leaf maple and Chipkit and other platform development boards of 3.3V.
Features:
-Quad-Band 850 / 900/ 1800 / 1900 MHz - would work on GSM networks in all countries across the world.
-GPRS multi-slot class 10/8.
-GPRS mobile station class B.
-Compliant to GSM phase 2/2+.
-Class 4 (2 W @ 850 / 900 MHz).
-Class 1 (1 W @ 1800 / 1900MHz).
-Control via AT commands - Standard Commands: GSM 07.07 & 07.05 Enhanced Commands: SIMCOM AT Commands.
-Short Message Service - so that you can send small amounts of data over the network (ASCII or raw hexadecimal).
-Embedded TCP/UDP stack - allows you to upload data to a web server.
-RTC supported.
-Selectable serial port.
-Speaker and Headphone jacks.
-Low power consumption:1.5mA(sleep mode).
-Industrial Temperature Range: -40°C to +85 °C.
Specifications:
Application Ideas
-M2M (Machine 2 Machine) Applicatoions.
-Remote control of appliances.
-Remote Weather station or a Wireless Sensor Network.
-Vehicle Tracking System with a GPS module.
Instructions for Use:
-The computer can debug USB-TL. This version of 5-26V2A current power supply, recommended 5V voltage 2A current. After plugging in the Arduino motherboard, we must also connect our 5-26V2ADC power supply. The reason is that the GPRS Shield's boot current and maximum peak current need to be 2A at the maximum, but the USB port cannot provide such a large current, so it must be connected to a power supply device. The pin of the other power supply port leads to 3.7-4.5V power supply suitable for lithium battery power supply. Serial port, compatible with arduino microcontroller. The TL serial port is compatible with 3.3 and 5V microcontrollers.
-Make sure your SM card is not locked.
-The baud rate of GPRS Shield communication is preferably 19200bps8-N-1 (GPRS Shield automatically matches the baud rate by default).
Package Included:
1 Set Module Board
Notes:
1. Make sure your SIM card is unlocked.
2. The product is provided as is without an insulating enclosure. Please observe ESD precautions specially in dry (low humidity) weather.
3. The factory default setting for the GPRS Shield UART is 19200 bps 8-N-1. (Can be changed using AT commands).
4. Power select - select the power supply for GPRS shield(external power or 5v of arduino).
5. Power jack - connected to external 4.8~5VDC power supply.
6. Antenna interface - connected to external antenna.
7. Serial port select - select either software serial port or hareware serial port to be connected to GPRS Shield.
8. Hardware Serial - D0/D1 of Arduino.
9. Software serial - D7/D8 of Arduino.
10. Status LED - tell whether the power of SIM900 is on.
11. Net light - tell the status about SIM900 linking to the net.
12. UART of SIM900 - UART pins breakout of SIM900.
13. Microphone - to answer the phone call.
14. Speaker - to answer the phone call.
15. GPIO,PWM and ADC of SIM900 - GPIO,PWM and ADC pins breakout of SIM900.
16. Power key - power up and down for SIM900.
Description:
The GPRS Shield is based on SIM900 module from SIMCOM and compatible with Arduino and its clones. The GPRS Shield provides you a way to communicate using the GSM cell phone network. The shield allows you to achieve SMS, MMS, GPRS and Audio via UART by sending AT commands (GSM 07.07 ,07.05 and SIMCOM enhanced AT Commands). The shield also has the 12 GPIOs, 2 PWMs and an ADC of the SIM900 module(They are all 2V8 logic) present onboard.
1. Provide 2 kinds of antenna interfaces, compatible with various needs. This product is shipped with an antenna, and the antenna has an extension cable, so it is compatible with 2 interfaces.
2. SIM900 can be set via jumper cap and connected to any 2 pins of Arduino from D0 to D7, not only the hardware UART of D0D1.
3. Debug toggle switch, you can set the DEBUG port of SIM900 to connect to Arduino or connect to PC through ATMEGA8U2 / FT232 on Arduino for debugging.
4. The audio and microphone ports are led out.
5. The multiple IO ports of SIM900 are led out. If necessary, you can use a Dupont cable to connect the pins-refer to the schematic diagram and datasheet for specific pins.
6. 3 status indicator lights, and 3 buttons-the power on button can be used to power on SIM900 by using the Arduino pin control to reach the software.
7. 3.3V and 5V automatic level compatible, it can adapt to 3.3V or 5V main control board, support leaf maple and Chipkit and other platform development boards of 3.3V.
Features:
-Quad-Band 850 / 900/ 1800 / 1900 MHz - would work on GSM networks in all countries across the world.
-GPRS multi-slot class 10/8.
-GPRS mobile station class B.
-Compliant to GSM phase 2/2+.
-Class 4 (2 W @ 850 / 900 MHz).
-Class 1 (1 W @ 1800 / 1900MHz).
-Control via AT commands - Standard Commands: GSM 07.07 & 07.05 Enhanced Commands: SIMCOM AT Commands.
-Short Message Service - so that you can send small amounts of data over the network (ASCII or raw hexadecimal).
-Embedded TCP/UDP stack - allows you to upload data to a web server.
-RTC supported.
-Selectable serial port.
-Speaker and Headphone jacks.
-Low power consumption:1.5mA(sleep mode).
-Industrial Temperature Range: -40°C to +85 °C.
Specifications:
Application Ideas
-M2M (Machine 2 Machine) Applicatoions.
-Remote control of appliances.
-Remote Weather station or a Wireless Sensor Network.
-Vehicle Tracking System with a GPS module.
Instructions for Use:
-The computer can debug USB-TL. This version of 5-26V2A current power supply, recommended 5V voltage 2A current. After plugging in the Arduino motherboard, we must also connect our 5-26V2ADC power supply. The reason is that the GPRS Shield's boot current and maximum peak current need to be 2A at the maximum, but the USB port cannot provide such a large current, so it must be connected to a power supply device. The pin of the other power supply port leads to 3.7-4.5V power supply suitable for lithium battery power supply. Serial port, compatible with arduino microcontroller. The TL serial port is compatible with 3.3 and 5V microcontrollers.
-Make sure your SM card is not locked.
-The baud rate of GPRS Shield communication is preferably 19200bps8-N-1 (GPRS Shield automatically matches the baud rate by default).
Package Included:
1 Set Module Board
Notes:
1. Make sure your SIM card is unlocked.
2. The product is provided as is without an insulating enclosure. Please observe ESD precautions specially in dry (low humidity) weather.
3. The factory default setting for the GPRS Shield UART is 19200 bps 8-N-1. (Can be changed using AT commands).
4. Power select - select the power supply for GPRS shield(external power or 5v of arduino).
5. Power jack - connected to external 4.8~5VDC power supply.
6. Antenna interface - connected to external antenna.
7. Serial port select - select either software serial port or hareware serial port to be connected to GPRS Shield.
8. Hardware Serial - D0/D1 of Arduino.
9. Software serial - D7/D8 of Arduino.
10. Status LED - tell whether the power of SIM900 is on.
11. Net light - tell the status about SIM900 linking to the net.
12. UART of SIM900 - UART pins breakout of SIM900.
13. Microphone - to answer the phone call.
14. Speaker - to answer the phone call.
15. GPIO,PWM and ADC of SIM900 - GPIO,PWM and ADC pins breakout of SIM900.
16. Power key - power up and down for SIM900.
Payment Terms
1.We accept PayPal only.
2.All major credit cards are accepted through secure payment processor PayPal.
3.Payment must be received within 7 business days of auction closing.
4.We ship to your eBay or Paypal address. Please make sure your eBay and Paypal address is correct before you pay.
2.All major credit cards are accepted through secure payment processor PayPal.
3.Payment must be received within 7 business days of auction closing.
4.We ship to your eBay or Paypal address. Please make sure your eBay and Paypal address is correct before you pay.
Shipping Terms
- For remote regions, we will charge your extra shipping costs. Usually it cost about 35USD-50USD. We will contact you after your payment. Thanks for your understanding.
Return Terms
1. If you receive defective item, please kindly notify us within 14 days. We will guide you the returning instruction for replacement or refund.
2. If you purchased in improper condition, please NOTE that the sipping and handling fee will not be refund, all return shipping fee should paid by the buyer unless item DOA.
3. We reserve the right to refuse any returns for objective reasons.
2. If you purchased in improper condition, please NOTE that the sipping and handling fee will not be refund, all return shipping fee should paid by the buyer unless item DOA.
3. We reserve the right to refuse any returns for objective reasons.
Custom Duties & Taxes
1. Import duties, taxes, and charges are not included in the item price or postage cost. These charges are the buyer's responsibility.
2. Avoiding some unnecessary trouble, please check with your country's customs office to inform us what we should declare its value before shipping.
2. Avoiding some unnecessary trouble, please check with your country's customs office to inform us what we should declare its value before shipping.
Feedback
1. If you are dissatisfied for any reason, please don't be quick to leave us neutral or negative feedback. We work hard to make sure EVERY CUSTOMER 100% SATISFIED and resolve any problem for you and always leave positive feedback to all our customers.
2. If you are satisfied with the product you received, please kindly leave us a positive feedback and 5 star DSR. If there is any problem of your order, please feel free to contact us firstly, we are responsible and credible seller, will follow it for you asap.
2. If you are satisfied with the product you received, please kindly leave us a positive feedback and 5 star DSR. If there is any problem of your order, please feel free to contact us firstly, we are responsible and credible seller, will follow it for you asap.
