Product Description

W1209 12V -50-110°C Digital Thermostat Temperature Control Switch Sensor + Case

Specifications:

Temperature Control Range: -50 C to +110 C (-58 F to +230 F)

Resolution at -9.9 to 99.9: 0.1 C

Resolution at all other temperatures: 1 C

Measurement Accuracy: 0.1 C

Control Accuracy: 0.1 C

Refresh Rate: 0.5 Seconds

Input Power (DC): 6V to 12V @ 65mA maximum (Provides power for the module, not the load)

NOTE: The maximum input support voltage should not exceed 12V. In applications such as an automobile or RV where the battery voltage can exceed 12V, a regulator circuit such as a 1N5349A zener diode and a series resistor in the range of 20 Ohm 1W should be used to limit the voltage to 12V. Alternately, a 12V to 9V buck voltage converter with the input to the converter connected to the battery and the output to the W1209 will provide a stable 9V DC supply for the W1209.

Measuring Input: NTC (10K 0.5%)

Waterproof Sensor: 0.5M cable

Probe tip dimensions: 20mm long x 4mm diameter

Output: 1 Channel Relay Output, Capacity: 20A at 14V DC, 16A at 24V DC, or 7A at 125V AC

Includes a Clear Acrylic Case (Box)

Power Consumption:

Static Current: <=35mA

Operating Current: <=65mA

Environmental Requirements:

Temperature: -10 ~ 60 C

Humidity: 20-85%

Dimensions:

W1209 Board (LxWxH): 48mm x 40mm x 14mm (1.9" x 1.6" x 0.6")

Case (Assembled L x W x H): 59mm x 51mm x 18mm (2.3" x 2.0" x 0.71")

The display defaults to showing the measured temperature.

Short press the "SET" button and then press "+" and "-" buttons to raise or lower the temperature setpoint.

Long press the “SET” button to activate the menu in order to change the P0 through P6 parameters listed in the Settings Chart below.

The setpoint and all parameter settings are stored in nonvolatile memory and will be retained if power to the controller is turned off.

The cooler, heater or fan is connected to a power supply through the relay contacts K0 and K1, and the temperature on/off setpoints are programmed into the W1209 using the onboard Set, Increase and Decrease buttons and display. The relay contacts are then open and closed, acting as a power switch for the cooler/heater, based on the temperature measured by the NTC temperature sensor (included with the module) and the setpoints programmed into the W1209 controller.

Although this module has an embedded microcontroller, no programming knowledge is required. 3 tactile switches allow for configuring various parameters including on & off trigger temperatures. The on-board relay can switch up to a maximum of 20A at 14V DC, 16A at 24V DC, or 7A at 125V AC. The current temperature is displayed in degrees Centigrade via its 3 digit seven segment display and the current relay state by an on board LED.

Settings Chart:

Code: Description / Range / Default Value

P0: Set Heating or Cooling Mode / C/H / C

P1: Hysteresis Set / 0.1C - 15C / 2C

P2: Upper Temperature Limit / 110C / 110C

P3: Lower Temperature Limit / -50C / -50C

P4: Temperature Calibration / -7.0C ~ 7.0C / 0C

P5: Delay Start Time / 0-10 mins / 0 mins

P6/P7: High Temperature Alarm / 0C - 110C / OFF

P8: Factory Reset (Not included in all firmware versions. Can also be reset by pressing and holding the + and - buttons for 5 seconds.)

Package Includes:

1×W1209 Temperature Control Switch Sensor Module

1set Acrylic Clear Case Box with mounting screws (assembly required)

Payment
Shipping
Returns
Contact Us

Payment should be completed within 4 days after buyer places the order,or else an unpaid case will be opened in order to cancel the transaction.

If you can not pay in time, please contact us.

All of the items will be shipped to buyer's EBAY address,please confirm your address on Ebay before you buy.

Your order will be usually shipped out the same or next business days once the payment is made and cleared.

All items will be checked before packing. All items are new and of high quality.

If to AU, we will ship your order by EDIS, it will take about 8 to 12 business days to you, and you can track it on line.

If to other country, we will ship your order by China Post or Singapore Registered Air Mail, it will take about 15-21 working days to you, you aslo can track it on line. Delivery time is about 14-28 business days and it may take up to 8 weeks to some European countries and South American countries due to strict custom inspection. We ship worldwide.

Please note that some countries will have custom duty or tax for certain items. It is the buyer's responsibility to pay all endued custom duty or tax. We are not responsible for any custom duty or tax since our price do not include this charge.

As shipping is affected by many unsteady factors: customs, flights, weather, war, trade policy ,etc, some shipments do get delayed sometimes. If you have not received your shipment within 15 days from payment, please contact us. We will track the shipment and get back to you as soon as possible with a reply.

Our goal is customer satisfaction!

Please contact us on ebay before returning the item We will provide you with a return address！

30day Warranty with Exchange for defective, malfunctioned, incorrect or partsmissing items.

Please notify us and return the item with all parts and accessories packed and marked "FOR EXCHANGE" within 14 days of receipt.

If defective, malfunctioned or parts-missing items are no longer available, a refund may be issued.
All returning postage costs will be the responsibility of the buyers under all circumstances.

If you encounter any problems about anything, please feel free to contact us and we will do our best to assist you solve the issue. If you are not satisfied in anyway, please feel free to let us know and give us a second chance to correct it before you decide to leave any neutral or negative feedback.

Please contact us through eBay link if you have any questions. We will reply you within 24- 48 hours. Please check you spam mail if no response for 48 hours.

Payment