Over 10 Years of Bringing You Thousands of Quality Items at the Best Prices Around!
We Must Be Doing Something Right!
We Must Be Doing Something Right!
SmartSense Blower Motor Resistor for Citroen Saxo/Xsara/Xantia/Berlingo/ZX/AX
Click on the image below to get zoomed view of the item
SmartSense™ Blower Motor Resistor/Control Module
OEM quality heater resistor/control module to repair broken heating in cars. Comes with 3 Year Warranty.
Cut out the middle-man and buy direct from ServiceX LTD, the sole UK & Europe distributor for SmartSense products.
Branded Parts at Unbranded Prices!
Compatibility
AX (1987-1997)
XM (1989-1995)
XM II (1995-200)
ZX (1991-1998) - Vehicles with Air Conditioning (both Valeo and Behr Units). For veicles without Air Conditioning SEE HERE
Berlingo VP (M49) (1996-2002) - Vehicles with Air Conditioning. For vehicles without Air Conditioning SEE HERE
Berlingo VU (M49) (1996-2002) - Vehicles with Air Conditioning. For vehicles without Air Conditioning SEE HERE
Saxo (1996-2003) - Vehicles with Air Conditioning
Xsara (1997-2000) - Vehicles with Regular Air Conditioning
Xsara II (2000-2006) - Vehicles with Regular Air Conditioning
Xantia (1993-1998) - Vehicles with Single Air Conditioning until RPO 06367
Xantia (1993-1998) - Vehicles with Regular Air Conditioning
Xantia II (1998-2002) - Vehicles with Air Conditioning
Interchangeable Part Numbers:
Citroen: 6441.78
Hella: 5HL351321601
Valeo: 698032
Febi: 28311
Behr: 5HL351321601
Meylw: 11148350000
Vemo: V42790001
847283W
847283R
Please compare the part number with your original part to ensure correct operation and fitment. Some vehicles may use more than one part number depending on configuration. If in doubt please email us your chassis/VIN number and we will let you know the correct part you need for your car.
Symptoms of a Blown Resistor
A faulty resistor can cause a number of problems with the heating/HVAC system of a car, including but not limited to:
- No hot air
- Heating only working intermittently
- Heating only working on some settings (when the resistor is bypassed)
We are so confident that you will be not be disappointed with these that we offer a 14-Day No Quibble Money Back Guarantee.
*** Same Day Free First Class Shipping for Orders Placed By 3PM (Mon-Fri) ***
There are numerous guidelines and instructions on owner forums, the internet and on YouTube. However as this is a service part we recommend installation by a qualified professional.
When installed it is IMPERATIVE to monitor the temperature of the resistor on first use. Sometimes a blown resistor can be a symptom of the problem and not the problem itself, and replacing it in this scenario will only cause it to blow again. If the resistor starts heating very quickly and getting too hot IMMEDIATELY SWITCH OFF YOUR CAR and diagnose the problem elsewhere. Resistors usually blow when they get too hot and this happens when too much current is being drawn from then. This can happen if there is an issue with the blower motor or even the ignition system, or a fault with the wiring. Also please check your fan is not jamming because of dirt or grease build up, or a failure in the bearings. This will also cause the fan to try to draw more power in an attempt to spin, causing the resistor to overheat and fail.
If replacing the resistor (and it is not getting hot) your heater still does not work, please check the thermo fuse or carry out further diagnosis elsewhere for a fault.
When installed it is IMPERATIVE to monitor the temperature of the resistor on first use. Sometimes a blown resistor can be a symptom of the problem and not the problem itself, and replacing it in this scenario will only cause it to blow again. If the resistor starts heating very quickly and getting too hot IMMEDIATELY SWITCH OFF YOUR CAR and diagnose the problem elsewhere. Resistors usually blow when they get too hot and this happens when too much current is being drawn from then. This can happen if there is an issue with the blower motor or even the ignition system, or a fault with the wiring. Also please check your fan is not jamming because of dirt or grease build up, or a failure in the bearings. This will also cause the fan to try to draw more power in an attempt to spin, causing the resistor to overheat and fail.
If replacing the resistor (and it is not getting hot) your heater still does not work, please check the thermo fuse or carry out further diagnosis elsewhere for a fault.