Description
SG-4162AD Digital RF Signal Generator 150MHz RF Signal Source Frequency Meter Frequency Counter
Features:
- Frequency range: 100kHz-150MHz
- 8-digit display of internal or external frequency
- Output waveform: sine wave
- In-band and out-of-band modulation
- Frequency meter: 10Hz-150MHz
Application:
SG-4162AD function signal generator is suitable for scientific research and experiment of electronic circuits and pulse circuits.
Performance Parameters:
Output Signal:
- Frequency range: A: 100kHz-300kHz; B: 300kHz-1MHz; C: 1MHz-3.2MHz; D: 3MHz-10MHz; E: 10MHz-35MHz; F: 32MHz-150 MHz; 3rd harmonic up to 450MHz
- Frequency accuracy: ±reading accuracy ±1-digit
- Output amplitude: 100mVrms (at 35MHz)
- Amplitude control: 0dB, 20dB and fine adjustment
- Modulation: Inner: 1kHz; Outer: 50Hz-20kHz (<1Vrms)
- Audio output: 1kHz (fixed, ≥1Vrms)
Frequency Meter:
- Frequency range: Low frequency: 10Hz-10MHz; High frequency: 10MHz-150MHz
- Sensitivity: <50mV
- Input impedance: low frequency: 1MΩ; high frequency: 50Ω
- Maximum input voltage: about <3V
General Parameters:
- Power supply: AC 220V±10%, 50-60Hz (110V±10% optional)
- Working environment: 0â to 40â/≤90%RH
- Size: 310 x 100 x 260mm/12.2 x 3.9 x 10.2"
- Weight: 3.8kg/8.4 lb
Package Included:
- 1 x Set of Signal Generator
Instructions For Use:
1. Ready to operate
1) The power switch is set to OFF.
2) Connect the power cord and plug it in.
3) Connect the high-frequency signal output line to the output terminal.
4) Select the frequency range and adjust the frequency knob to reach the required frequency.
5) The output line should be as short as possible to avoid absorbing unwanted noise. Long shielded lines can reduce the frequency response of high frequency bands, especially when using square waves.
2. Connection
When the signal wire is connected to the output, the red wire is high potential (or fire wire), the black wire is the ground wire and is connected to the chassis.
If high-frequency signals are to be connected to the antenna input of the receiver, a 50 to 200 Ω resistor should be connected in series. If receiving with a rod antenna, connect a coil with a few turns of wire on the test line to couple the signal to the antenna.
When detecting a high frequency and an intermediate frequency amplifying circuit, a middle to go through . 1-5pF small capacitance, in order to avoid detuning effect.
Note: When directly connecting the test circuit, make sure that there is no high DC voltage in the circuit under test. Otherwise, the frequency may be connected in series a 0.05 [mu] F. - 100pF capacitance.
Features:
- Frequency range: 100kHz-150MHz
- 8-digit display of internal or external frequency
- Output waveform: sine wave
- In-band and out-of-band modulation
- Frequency meter: 10Hz-150MHz
Application:
SG-4162AD function signal generator is suitable for scientific research and experiment of electronic circuits and pulse circuits.
Performance Parameters:
Output Signal:
- Frequency range: A: 100kHz-300kHz; B: 300kHz-1MHz; C: 1MHz-3.2MHz; D: 3MHz-10MHz; E: 10MHz-35MHz; F: 32MHz-150 MHz; 3rd harmonic up to 450MHz
- Frequency accuracy: ±reading accuracy ±1-digit
- Output amplitude: 100mVrms (at 35MHz)
- Amplitude control: 0dB, 20dB and fine adjustment
- Modulation: Inner: 1kHz; Outer: 50Hz-20kHz (<1Vrms)
- Audio output: 1kHz (fixed, ≥1Vrms)
Frequency Meter:
- Frequency range: Low frequency: 10Hz-10MHz; High frequency: 10MHz-150MHz
- Sensitivity: <50mV
- Input impedance: low frequency: 1MΩ; high frequency: 50Ω
- Maximum input voltage: about <3V
General Parameters:
- Power supply: AC 220V±10%, 50-60Hz (110V±10% optional)
- Working environment: 0â to 40â/≤90%RH
- Size: 310 x 100 x 260mm/12.2 x 3.9 x 10.2"
- Weight: 3.8kg/8.4 lb
Package Included:
- 1 x Set of Signal Generator
Instructions For Use:
1. Ready to operate
1) The power switch is set to OFF.
2) Connect the power cord and plug it in.
3) Connect the high-frequency signal output line to the output terminal.
4) Select the frequency range and adjust the frequency knob to reach the required frequency.
5) The output line should be as short as possible to avoid absorbing unwanted noise. Long shielded lines can reduce the frequency response of high frequency bands, especially when using square waves.
2. Connection
When the signal wire is connected to the output, the red wire is high potential (or fire wire), the black wire is the ground wire and is connected to the chassis.
If high-frequency signals are to be connected to the antenna input of the receiver, a 50 to 200 Ω resistor should be connected in series. If receiving with a rod antenna, connect a coil with a few turns of wire on the test line to couple the signal to the antenna.
When detecting a high frequency and an intermediate frequency amplifying circuit, a middle to go through . 1-5pF small capacitance, in order to avoid detuning effect.
Note: When directly connecting the test circuit, make sure that there is no high DC voltage in the circuit under test. Otherwise, the frequency may be connected in series a 0.05 [mu] F. - 100pF capacitance.
Payment Terms
1.We accept PayPal only.
2.All major credit cards are accepted through secure payment processor PayPal.
3.Payment must be received within 7 business days of auction closing.
4.We ship to your eBay or Paypal address. Please make sure your eBay and Paypal address is correct before you pay.
2.All major credit cards are accepted through secure payment processor PayPal.
3.Payment must be received within 7 business days of auction closing.
4.We ship to your eBay or Paypal address. Please make sure your eBay and Paypal address is correct before you pay.
Shipping Terms
- For remote regions, we will charge your extra shipping costs. Usually it cost about 35USD-50USD. We will contact you after your payment. Thanks for your understanding.
Return Terms
1. If you receive defective item, please kindly notify us within 14 days. We will guide you the returning instruction for replacement or refund.
2. If you purchased in improper condition, please NOTE that the sipping and handling fee will not be refund, all return shipping fee should paid by the buyer unless item DOA.
3. We reserve the right to refuse any returns for objective reasons.
2. If you purchased in improper condition, please NOTE that the sipping and handling fee will not be refund, all return shipping fee should paid by the buyer unless item DOA.
3. We reserve the right to refuse any returns for objective reasons.
Custom Duties & Taxes
1. Import duties, taxes, and charges are not included in the item price or postage cost. These charges are the buyer's responsibility.
2. Avoiding some unnecessary trouble, please check with your country's customs office to inform us what we should declare its value before shipping.
2. Avoiding some unnecessary trouble, please check with your country's customs office to inform us what we should declare its value before shipping.
Feedback
1. If you are dissatisfied for any reason, please don't be quick to leave us neutral or negative feedback. We work hard to make sure EVERY CUSTOMER 100% SATISFIED and resolve any problem for you and always leave positive feedback to all our customers.
2. If you are satisfied with the product you received, please kindly leave us a positive feedback and 5 star DSR. If there is any problem of your order, please feel free to contact us firstly, we are responsible and credible seller, will follow it for you asap.
2. If you are satisfied with the product you received, please kindly leave us a positive feedback and 5 star DSR. If there is any problem of your order, please feel free to contact us firstly, we are responsible and credible seller, will follow it for you asap.
On Sep-05-21 at 21:14:48 PDT, seller added the following information:
