eBay

PRODUCT DESCRIPTION

Proto-PIC Digital RGB LED Weatherproof Strip 60 LED - 1m-BLACK, 5V, PCB Material

You thought it couldn’t get better than our world-famous 32-LED-per-meter Digital LED strip but we will prove you wrong! Did you want twice the LEDs? We got it (well, it's 1.875 times as many but that’s within a margin of error). Did you want thinner strips? Now only 12.5 mm wide, 10 mm if you remove the strip from the casing. You wanted a less noticeable strip colour – this strip has black-coloured flex PCB, which will be less visible against white-painted walls. This is the strip with BLACK flex PCB, it's identical to the WHITE 60 LED/meter except it has a different colour mask on the flex strip

Few Things:

First up, the higher density means much higher power usage over a certain distance – 18 Watts max (~3.5 Amps @ 5V) per meter instead of 9.6 Watts max (~2 Amps @ 5V). The max rating is assuming all the LEDs are on full white, usually, the actual current for colourful design is about 1/3 to 1/2 the max current. A good power supply such as our 5V 10A supply is key!

Second, to get high density, the controller chip is inside the LED, which is kind of cool, but also means that the chip only uses a single pin for input and a single pin for output. The protocol used is very very timing-specific and can only be controlled by microcontrollers with highly repeatable 100nS timing precision. We have an example code for using with the Arduino Uno/Mega microcontroller at 8MHz and 16MHz, but it will not work with the Raspberry Pi, Basic Stamp, NETduino, any other interpreted/virtual machine microprocessor or any processor slower than 8 MHz. For those processors, check our 32 LED/meter digital LED strip which has SPI-like input/output and works well with Pi, NETduino, and other processors.

Third, just because you have all those pixels doesn’t mean you have the RAM for it – the entire strip must be buffered in memory, and we’ve found many Arduino UNO projects only have about 1500 bytes of RAM available after all the extras are included – enough for about 500 LED pixels. If you want to drive the entire strip and have some other libraries included, use a Mega.

These LED strips are even more fun and glowy. There are 60 RGB LEDs per meter, and you can control each LED individually! Yes, that’s right, this is the digitally-addressable type of LED strip. You can set the colour of each LED’s red, green and blue component with 8-bit PWM precision (so 24-bit colour per pixel). The LEDs are controlled by shift registers that are chained up down the strip so you can shorten or lengthen the strip. Only 1 digital output pin are required to send data down. The PWM is built into each LED chip so once you set the colour you can stop talking to the strip and it will continue to PWM all the LEDs for you.

The strip is made of flexible PCB material and comes with weatherproof sheathing. You can cut this stuff pretty easily with wire cutters, there are cut-lines every 0.65″/1.7cm (1 LED each). Solder to the 0.1″ copper pads and you’re good to go. Of course, you can also connect strips to make them longer, just watch how much current you need! You must use a 5V DC power supply to power these strips, do not use higher than 6V or you can destroy the entire strip

They come in 4-meter reels with a 2 or 3-pin JST SM connector on each end and separated power/ground wires. These strips are sold by the meter! If you buy 4 meters at a time, you’ll get full reels with two connectors. If you buy less than 4m, you’ll get a single strip, but it will be a cut piece from a reel that may or may not have a connector on it.

To wire up these strips we suggest picking up some JST SM plug and receptacle cables. You’ll want one of each, one wire is for ground the other is for signal. For the power wire, you will also probably want a 2.1mm DC jack to wire in so you can connect one of our wall adapters to power it.

Features:

Digital RGB LED Weatherproof Strip 60 LED
Less noticeable strip colour
This strip has a black-coloured flex PCB
10 mm if you remove the strip from the casing
Visible against white-painted walls
Has a different colour mask on the flex strip
The strip is made of flexible PCB material

Proto-PIC Digital RGB LED Weatherproof Strip 60 LED - 1m-BLACK, 5V, PCB Material You thought it couldn’t get better than our world-famous 32-LED-per-meter Digital LED strip but we will prove you wrong! Did you want twice the LEDs? We got it (well, it's 1.875 times as many but that’s within a margin of error). Did you want thinner strips? Now only 12.5 mm wide, 10 mm if you remove the strip from the casing. You wanted a less noticeable strip colour – this strip has black-coloured flex PCB, which will be less visible against white-painted walls. This is the strip with BLACK flex PCB, it's identical to the WHITE 60 LED/meter except it has a different colour mask on the flex strip Few Things: First up, the higher density means much higher power usage over a certain distance – 18 Watts max (~3.5 Amps @ 5V) per meter instead of 9.6 Watts max (~2 Amps @ 5V). The max rating is assuming all the LEDs are on full white, usually, the actual current for colourful design is about 1/3 to 1/2 the max current. A good power supply such as our 5V 10A supply is key! Second, to get high density, the controller chip is inside the LED, which is kind of cool, but also means that the chip only uses a single pin for input and a single pin for output. The protocol used is very very timing-specific and can only be controlled by microcontrollers with highly repeatable 100nS timing precision. We have an example code for using with the Arduino Uno/Mega microcontroller at 8MHz and 16MHz, but it will not work with the Raspberry Pi, Basic Stamp, NETduino, any other interpreted/virtual machine microprocessor or any processor slower than 8 MHz. For those processors, check our 32 LED/meter digital LED strip which has SPI-like input/output and works well with Pi, NETduino, and other processors. Third, just because you have all those pixels doesn’t mean you have the RAM for it – the entire strip must be buffered in memory, and we’ve found many Arduino UNO projects only have about 1500 bytes of RAM available after all the extras are included – enough for about 500 LED pixels. If you want to drive the entire strip and have some other libraries included, use a Mega. These LED strips are even more fun and glowy. There are 60 RGB LEDs per meter, and you can control each LED individually! Yes, that’s right, this is the digitally-addressable type of LED strip. You can set the colour of each LED’s red, green and blue component with 8-bit PWM precision (so 24-bit colour per pixel). The LEDs are controlled by shift registers that are chained up down the strip so you can shorten or lengthen the strip. Only 1 digital output pin are required to send data down. The PWM is built into each LED chip so once you set the colour you can stop talking to the strip and it will continue to PWM all the LEDs for you. The strip is made of flexible PCB material and comes with weatherproof sheathing. You can cut this stuff pretty easily with wire cutters, there are cut-lines every 0.65″/1.7cm (1 LED each). Solder to the 0.1″ copper pads and you’re good to go. Of course, you can also connect strips to make them longer, just watch how much current you need! You must use a 5V DC power supply to power these strips, do not use higher than 6V or you can destroy the entire strip They come in 4-meter reels with a 2 or 3-pin JST SM connector on each end and separated power/ground wires. These strips are sold by the meter! If you buy 4 meters at a time, you’ll get full reels with two connectors. If you buy less than 4m, you’ll get a single strip, but it will be a cut piece from a reel that may or may not have a connector on it. To wire up these strips we suggest picking up some JST SM plug and receptacle cables. You’ll want one of each, one wire is for ground the other is for signal. For the power wire, you will also probably want a 2.1mm DC jack to wire in so you can connect one of our wall adapters to power it. Features: Digital RGB LED Weatherproof Strip 60 LED Less noticeable strip colour This strip has a black-coloured flex PCB 10 mm if you remove the strip from the casing Visible against white-painted walls Has a different colour mask on the flex strip The strip is made of flexible PCB material

Specifications

Colour Black
Wide 12.5 mm wide
Remove the Casing 10 mm Wide
Visible visible against white-painted walls
Type RGB LED
Features Weatherproof
Flex Strip Has the different colour mask
Come In 4-meter reels with a 2 or 3-pin JST
UPC 5055421070014
MPN HC-F5V-60L-60LED-B-WS2812B IP6
Strip 60 LED Per Meter
Made of Flexible PCB material
Brand Proto-PIC

ABOUT US

Welcome to the Hot Solder Ebay Store – an Electronic Components Supplier in Scotland and a central hub for all Educators and Makers. Your source for all things Proto-PIC, BBC Micro:Bit, Sparkfun, Pololu, Raspberry PI and Arduino. Founded in 2006, our first in-house developed product was the Proto-PIC Arduino Starter Kit. We have sold over 10,000 of these to date. We now have a full range of products that are our own concept and design.

We are one of the country’s most knowledgeable, quality-driven electronics components supplier. A passionate group of engineering, technical and industry experts. Our mission is to help our customers quickly find the electronic components they need at competitive prices either by sourcing through our suppliers or manufacturing ourselves. We are fluent with Arduino and Raspberry PI languages.

Hot Solder is proud to work with schools, colleges, universities and other educational organizations around the UK working collaboratively to develop computer science in the classroom, support professional development, provide kits and components, as well as, online training via our online Academy. We have helped educational institutions create STEM curriculum for their academic year, design a series of projects for progression and implement makerspaces and more.

PAYMENT

We accept payment by PayPal and Credit / Debit cards entered on eBay only. You must be registered with PayPal or eBay to buy from us.

SHIPPING

We ship via Royal Mail the very same day you order, so long as you order before 2pm. We offer free economy shipping and have tracked and express options available too.

All of our shipping methods have either a tracking number or a delivery confirmation number, and this information will be provided once the item has shipped. Delivery estimates are generated in real time and can be seen in the "shipping & payments" tab

RETURNS

Our returns policy is in accordance with the Consumer Protection (Distance Selling) Regulations 2000. If you have any specific queries regarding our returns policy please email us.

You may return your goods any time for any reason within 30 days of receipt for a no quibble refund of the full purchase price.

If you would like to make use of our 30-day refund policy, or if you are not satisfied with your goods for any reason, please contact us with your order details and we will endeavour to resolve any issue you may have.

Hot Solder produces a range of electronic projects developed to teach to wide range of STEM skills for people of all ages. From early development years to seasoned techno junkies and all inbetween.

We are located in the UK, more specifically fife, and with almost pin point accuracy here:

Address:

Hot Solder Limited, Unit 26, Dunnikier Business Park, Kirkcaldy, Fife, Scotland, KY1 3LW

WHAT OUR CUSTOMERS ARE SAYING ABOUT US

good seller	shagx (1367 )
Fast delivery	the_topaz_ro (2384 )
Fast delivery. All good. Thanks!	brac-5 (46 )
highly recommended.	tony_carino5 (75 )
Many thanks !!!	energy.frequ (1515 )