BOXI
  • Pretty Auto is one of the fast-growing automotive aftermarket parts online providers in America. With more than 25 years experience in the industry, All parts will meet or exceed OE specifications, which will be an ideal choice to replace your broken parts.
  • Placement of lift supports,struts,dampers could be front or rear hood, trunk, tailgate,liftgate, trunk lid, hatch,rear window glass,tailgate assit,storage box and so on.
  • Also supply a variety of mortor parts, such as ABS sensor, door handle, cooling fan, ERG value, water pump, window regular, blower assembly, fuel pump, ignition coil, belt tensioner assembly, valve cover, thermostat assembly, TPMS sensor, VTT Valve, timing chain kit, hub bearing assembly etc.....

Specification:

Product information:
Placement on Vehicle: Front hood Left & Right
Extended Length[in]: 19.35''
Compressed Length[in]:11.85"
Reference Number: 6312,SG314038

Fitment:
  • Fits the following Dodge Dakota PickupYears:
  • 2005-2011 | Base Crew Cab
  • 2005-2011 | Base Extended Cab
  • 2009-2011 | Big Horn Crew Cab
  • 2009-2011 | Big Horn Extended Cab
  • 2005-2011 | Laramie Crew Cab
  • 2005-2011 | Laramie Extended Cab
  • 2009-2011 | Lone Star Crew Cab
  • 2009-2011 | Lone Star Extended Cab
  • 2005-2011 | SLT Crew Cab /2005-2011 | SLT Extended Cab
  • 2005-2008 | ST Crew Cab / 2005-2011 | ST Extended Cab
  • 2005-2011 | SXT Crew Cab /2005-2011 | SXT Extended Cab
  • 2005-2011 | Sport Crew Cab / 2005-2011 | Sport Extended Cab
  • 2005-2011 | TRX Crew Cab / 2005-2011 | TRX Extended Cab
  • 2008-2011 | TRX4 Crew Cab / 2008-2011 | TRX4 Extended Cab
  • Fits the following Dodge Ram Dakota Pickup Years:
  • 2011 | Base Crew Cab
  • 2011 | Base Extended Cab
  • 2011 | Big Horn Crew Cab
  • 2011 | Big Horn Extended Cab
  • 2011 | Laramie Crew Cab
  • 2011 | Laramie Extended Cab
  • 2011 | Lone Star Crew Cab
  • 2011 | Lone Star Extended Cab / 2011 | ST Extended Cab
  • 2011 | TRX4 Crew Cab / 2011 | TRX4 Extended Cab
  • Fits the following Mitsubishi Raider Cab Pickup Years:
  • 2006-2009 | Base Crew Cab /2006-2009 | Base Extended Cab
  • 2006-2007 | DuroCross Crew Cab / 2006 | DuroCross Extended Cab
  • 2006-2009 | LS Crew Cab / 2006-2009 | LS Extended Cab
  • 2007 | SE Crew Cab / 2006 | XLS Crew Cab
    •  

    Easy to install:

     
  • Find Someone or Props hold the hatch, hood or rear window open while replacing the lift support, so that they can raise or lower it as needed.
  • Before removing the old lift supports, inspect the end connections and compare them the the units on your vehicle to make sure that they are the same as well as the extended length.
  • Remove the lift support struts retaining clips by using a flat head screwdriver.
  • Slowly turn the screw driver and it will lift up the retaining clips. Then pull the support away from the vehicle and it will release.
  • To install the new supports do the same procedure in the reverse. DO NOT jam the new support end over the ball socket without lifting the retaining clips slightly damage may occur.
  • Push the strut onto the ball joint. Place the strut over the ball joint and use your tool to apply pressure until it pops into place.
  • Move the Props to see whether the supports work good.
    		•

    Attention:


    Package Includes:
    2 × Lift Supports
     
    无标题文档