![]() |
![]() ![]() |
![]() ![]() |
![]() ![]() |
![]() ![]() |
![]() ![]() |
![]() ![]() |
Features:
Descriptions:
1. Apply a light coating retaining compound around the leading edge of crankshaft flange. Wipe away extra sealant. Installing Rear Oil Seal and Wear Sleeve.
2. Install JDG477 (85) Pilot (A) on end of crankshaft using the Allen head cap screws (B) supplied and tighten.
3. Start oil seal/wear sleeve assembly (C) overJDG477 (85) Pilot and crankshaft with open side of seal toward engine.
4. Position JDG478 Driver (A) so that hole in the crossplate goes over threaded stud of pilot. Install washerand nut on stud.
5. Tighten nut to draw JDG478 Driver in until cross bar bottoms on JDG477 (58) Pilot. When the tool bottoms,seal and wear ring assembly (B) will be correctly positioned.
6. Remove JDG476 (85) Tool Set from engine.
Item Specifics | |
---|---|
Brand | WM-Auto |
Manufacturer Part Number | WMQP-818 |
Type | JDG476 Crankshaft Rear Main Seal Installer |
Material | steel |
Compatibility | For John Deere Servicegard 7.6L 8.1L Engines |
Warranty | 1 Year |
Accepted: Payoneer, Paypal, Credit Card, Debit Card and many other mothods.
Please make sure your shipping address is correct before we ship.
Return postage is the responsibility of buyer unless the return is a result of our mistake.
And all NON-seller mistake returns for refund are subject to 20% re-stocking fee.
We maintain high standards of excellence Four 5-star rating and strive for 100% customer satisfaction! Positive Feedback
is very important to us. If you are not satisfied with our product or our Service, please feel free to contact us immediately.
Our office hours :
- 9:00 a.m. to 6:00 p.m. (GMT +8) of Monday to Friday
- 9:00 a.m. to 1:00 p.m. (GMT +8) of Saturday
Shop Category Picture Help & Info Payment Policy Shipping Policy Return Policy FAQ About Us |
JDG476 Crankshaft Rear Main Seal Installer for John Deere Servicegard 4045, 6076, 6081 and 6466 7.6L 8.1L Engines
Features:
Descriptions:
1. Apply a light coating retaining compound around the leading edge of crankshaft flange. Wipe away extra sealant. Installing Rear Oil Seal and Wear Sleeve. 2. Install JDG477 (85) Pilot (A) on end of crankshaft using the Allen head cap screws (B) supplied and tighten. 3. Start oil seal/wear sleeve assembly (C) overJDG477 (85) Pilot and crankshaft with open side of seal toward engine. 4. Position JDG478 Driver (A) so that hole in the crossplate goes over threaded stud of pilot. Install washerand nut on stud. 5. Tighten nut to draw JDG478 Driver in until cross bar bottoms on JDG477 (58) Pilot. When the tool bottoms,seal and wear ring assembly (B) will be correctly positioned. 6. Remove JDG476 (85) Tool Set from engine.
Payment
Accepted: Payoneer, Paypal, Credit Card, Debit Card and many other mothods. Shipping
Please make sure your shipping address is correct before we ship. Returns
Return postage is the responsibility of buyer unless the return is a result of our mistake. Feedback
We maintain high standards of excellence Four 5-star rating Contact Us
Our office hours : - 9:00 a.m. to 6:00 p.m. (GMT +8) of Monday to Friday All rights reserved. |