KERUI J009 Wireless siren host indoor aloud alarm with door sensor remotecontrol

---

Introduction

Integrated with a wireless strobe siren and host transmitter, this system can be applied not only to a wireless strobe siren, but also to a standalone alarm host. When any detector of this system is triggered, the host will immediately issue an alarm with a loud sound and a flashing warning signal with an exclusive blinding light to deter intruders. Host and detectors with wireless transmission, simple installation and humanized design. The user can assign the arming, disarming, volume control, emergency assistance, assistance, etc. Only with the help of a remote control. The user can configure multiple wireless magnetic door contacts, wireless IR detectors, wireless smoke detectors, wireless gas detectors, wireless carbon monoxide detectors, wireless vibration detectors, wireless infrared fences, wireless infrared and other accessories, if necessary.

---

Features:

1. Compact and fashionable mushroom shape design
2. wireless, do it yourself
3. Intelligent and adjustable volume with 8 levels (including mute)
4. Over-loud siren 110 dB, 4 groups of flashing lights
5. Information security EEPROM, information is never lost to ensure information security
6. Wireless intelligent learning coding, maximum support 20 pcs Remote control and 40 pcs Detector
7. Compatible with normal coding PT1527 (150K-470K) and PT2262 (resistance 1,5M-4,7M)
8. Built-in Ni-Hi battery 3.7 V / 600 mAh, in standby mode 8 hours above
9. AC / DC, 24/7 regular security without interruption.
10. AC 100-240 V

Instruction manual

1. On / off

AC On / Off: siren without on / off button. Insert the plug into the outlet, turn on the red power indicator and sound the “Di” sound signal, and the indicator will flash once to indicate successful connection, and then charge the built-in battery. The power indicator will change from red to green when the recharge ends. Unplug the device or turn off the power, the power indicator is off, and then the siren turns off (when the battery is turned off).

DC On / Off: Siren with DC on / off button for battery. When alternating current is turned off, DC turn on the direct current be, the device beeps once, the warning light flashes once, indicating that the battery power is on.

Notes: under the battery power source, connect the AC power, only the power indicator ； is lit under the AC power source, turn on the battery power, the light response of this device is absent.

2. Volume Control

8 levels of adjustable volume from loud to quiet, and then from quiet to loud in a cycle. The default volume is loud.

Adjustment: press the “SET” button on this device or the “S” button on the remote control, the volume changes from loud to quiet and then from quiet to loud. If only the warning light flashes once or twice, it means that the sound is muted; If the warning light flashes once or twice and beeps 1 or 2 times, this indicates the highest volume level.

Notes: During an alarm, press the “S” button on the remote control to adjust the volume. If you press the “SET” button, disarming is ON.

3. Warning Indicator Light

During arming, a siren sounds once, only one warning light flashes

When disarming, the buzzer beeps twice, the warning light flashes twice

4. Instructions for use as a wireless siren

As for the wireless strobe siren, please study the coding and connect to the siren and the wireless host before using. When the alarm host triggers, the siren will give a loud beep and the warning light will flash to prevent intrusion.

5. Explore coding settings with host

    5.1 Learning to coding

    Press the “SET” button for 3 seconds, give one beep, and the indicator will light up, and the siren will enter learning mode, and press the “ARM” button on the main device or the siren on button, a double beep means successful learning coding. If it is necessary to exit the training mode, press “SET” for 1 second, give a beep 3 times, the warning light is off. If no operation occurs for 20 seconds during training, the device automatically exits the training mode.

Notes: during training, please do not run the detectors.

    5.2 Check the correctness of the study encoding:

    Press "Emergency" on the host, turn on the host alarm, turn on the siren and flashing light that indicates successful learning. If the siren does not respond, study the coding again.

After successfully studying the code, 

Host Alarm	Wireless sound and light alarm
Host Arming	Beep twice and twice
Host Reserve Arming	Beep twice and twice
Host Disarming	Beep twice and twice

 

 

 

 

 

 

 

 

 

Notes: Some hosts cannot send an alarm and learn coding using a siren directly. In this case, please use the F8 transmitter.  

    5.3 Setting up work and learning to encode using an F8 transmitter

    5.3.1 Exploring coding with a transmitter (F8)

    First, insert the plug of the F8 transmitter into the siren socket. In the case of a wired alarm, you must disconnect the F8 connector, connect the red wire to the positive pole and the black wire to the negative pole of the wired alarm.

    Secondly, connect the siren to the outlet, turn on the battery, enter normal operating state, press the “SET” button for 3 seconds, the device will beep once, light up, and then go into training mode.

    Finally, open the back cover of the F8, press the white “trigger” button, the LED indicators of the F8 transmitter will light up and send a signal, the siren will sound two beeps, indicating successful learning. Press the SET button J009 once, give 3 beeps and turn off the alarm or wait 20 seconds to exit the learning mode.

    5.4 Operation between transmitter (F8) and strobe siren (J009)

    After successfully studying the code, press the “TEST” button on F8, the indicator will flash once and send a disarm signal to J009, then J009 will beep twice, indicating successful learning and wireless communication. Insert the F8 plug into the alarm host's siren output. When the host signals an alarm, the host will output a constant current to F8 from the cable, and F8 will send an alarm to J009, and J009 will beep and flash. After removing the host from the alarm, F8 will send a disarm signal to J009, J009 will stop the alarm.

    5.5 Remove all wireless accessories

    Press the “SET” button for 3 seconds, enter the learning mode, then press and hold the “SET” button for 3 seconds until you hear 3 beeps and blink six times and then do not light, and then remove all accessories. Please review the coding of the corresponding wireless accessory if necessary.

6. Instructions for use as a standalone alarm unit

Being a standalone alarm host, it can learn coding and connect with other wireless accessories together to become an independent alarm system. After assigning a hand, any detector will trigger, the host will immediately issue an alarm with the last loud sound for 5 minutes and a flashing alarm indicator to deter intruders.

    6.1 Learn coding with wireless accessories

Press the "SET" button for 3 seconds, give one beep, and the indicator lights up, indicating that the host is in the learning mode, and press any button on the remote control or activate any detector to send a signal to this device, double response A beep indicates successful learning coding. If only one beep means that the corresponding accessories have been added previously, and a three-time beep means the full quota of accessories.

Notes: maximum support 20 pcs. Remote control and 40 pcs. Detector

    6.2 Check the correctness of the study encoding:

Press the "Arming" button on the remote control, if the siren gives one beep or activates any detector, the response to the alarm, which indicates successful coding of the study. Otherwise, please re-examine.

    6.3 Remove all wireless accessories

Press the “SET” button for 3 seconds, enter the learning mode, then press and hold the “SET” button for 3 seconds until you hear six beeps and go out, and then remove all accessories. Please revisit the encoding of the corresponding wireless accessory if necessary.

7. Restore factory settings

Turn off the power, turn off the battery switch, then press and hold the ADD button when turning on the power. The device will respond with a beep six times, then release the "ADD" button. This function will reset all settings to factory defaults, all detectors and remote controls will be deleted.