Technical Parameter
Work bench size 410x316mm
Rated voltage and frequency AC220-230v/AC110V 60/50Hz
Complete machine power 1600W
Preheating plate power 1500W
Preheating plate size 280x270mm
Preheating plate temperature adjustable 0-450℃
Main Components:
Preheating plate main body 1
Temperature sensor 1
PCB board holder 1
Power line 1
User manual (compact disc) 1
Preheating plate main body 1
Temperature sensor 1
PCB board holder 1
Power line 1
User manual (compact disc) 1
Main component function explanation：
Compare with T860,IRDA WELDER add a Rework 936 and a 936 switch,more concenient than before.
1. Adopt infrared weld technology which independent exploration.
2. Use infrared heat,it is easy to cut through,heat proportion piercing tradition weld machine with sirocco.
3. Easily operate.Just need one day training.Can operation this machine.
4. No need weld tools,it can weld all the component of 15x15-25x25mm.
5. This machine has 650W heating system.widely to 80x120mm.
6. Infrared heating no have sirocco flow. Don't impact perimeter small component.Can suitable for all of the
component,especially Micro BGA component.
Parameter：
Working voltage : AC220V 50Hz
Output power: 800W
Temperature: 100℃-350℃
2. Use infrared heat,it is easy to cut through,heat proportion piercing tradition weld machine with sirocco.
3. Easily operate.Just need one day training.Can operation this machine.
4. No need weld tools,it can weld all the component of 15x15-25x25mm.
5. This machine has 650W heating system.widely to 80x120mm.
6. Infrared heating no have sirocco flow. Don't impact perimeter small component.Can suitable for all of the
component,especially Micro BGA component.
Parameter：
Working voltage : AC220V 50Hz
Output power: 800W
Temperature: 100℃-350℃
Operation method
1、Boot.
①Check the power source,wind the plug.
②Turn on the power source.Don’t use until pass check.Pand will display enactment value.When last time used.
③Installation the repair shell.Fix the line on the strip rack.Screw the light system height.Keep 20-30mm between light and welder machine.
④According to measurement of welder piece.Proprictily screw temperature.from60℃-350℃.When you strip 15×15mm piece.Choice temperature 240-300℃.When you strip 25×25mm piece.Choice temperature 300-350℃.The temperature come up to 350℃.The light system will shoot straightly.Please pay more attention to yourself control time.avoid burn out.
⑤Screw focus.The light system smallest diameter is 15mm .the biggest is 30mm.Normally keep 20-30mm.
⑥Turn on the two switches.They control warm-up plate and light system.
2、Dismantle and weld。
①Regulate temperature , make the chip focus
②After suitable for timing, the tin is clicked and melted, take out the chip。
3、Weld the chip。
①Clean the pad。
②Coating help solder flux (should not thick too , can have first more thin ) and soldering tin ball。
③Wait to help the solder flux to volatilize into the flux, heat and totally melt to the tin ball , place correctly with the clip , aim at the chip to weld into the position.
④936 searing-iron.Open the swich and enactment temperature.
Caution!
1、After use , imprison power immediately , make sure the light body cooling down,and place it in safety.After turning off the power switch
2、Keep the blowing way without hindered, the light body is clean.
3、The support in good time is polished with the oil to lead the post , focus
4、Disconnect the plug when you don’t use the it for a long time.
5、Operate carefully, take care。
②Turn on the power source.Don’t use until pass check.Pand will display enactment value.When last time used.
③Installation the repair shell.Fix the line on the strip rack.Screw the light system height.Keep 20-30mm between light and welder machine.
④According to measurement of welder piece.Proprictily screw temperature.from60℃-350℃.When you strip 15×15mm piece.Choice temperature 240-300℃.When you strip 25×25mm piece.Choice temperature 300-350℃.The temperature come up to 350℃.The light system will shoot straightly.Please pay more attention to yourself control time.avoid burn out.
⑤Screw focus.The light system smallest diameter is 15mm .the biggest is 30mm.Normally keep 20-30mm.
⑥Turn on the two switches.They control warm-up plate and light system.
2、Dismantle and weld。
①Regulate temperature , make the chip focus
②After suitable for timing, the tin is clicked and melted, take out the chip。
3、Weld the chip。
①Clean the pad。
②Coating help solder flux (should not thick too , can have first more thin ) and soldering tin ball。
③Wait to help the solder flux to volatilize into the flux, heat and totally melt to the tin ball , place correctly with the clip , aim at the chip to weld into the position.
④936 searing-iron.Open the swich and enactment temperature.
Caution!
1、After use , imprison power immediately , make sure the light body cooling down,and place it in safety.After turning off the power switch
2、Keep the blowing way without hindered, the light body is clean.
3、The support in good time is polished with the oil to lead the post , focus
4、Disconnect the plug when you don’t use the it for a long time.
5、Operate carefully, take care。
