Features:
Voltage :4.8-5 .5 v
Current: 1.6mA
Dimensions: 1.7cm * 2.9cm * 0.4cm
Disconnect J1 output rate 80hz, Connect J1 output rate 10hz
With metal shielding , Strong anti-interference ability.
Two selectable differential inputs.
On-chip low-noise programmable amplifier , selectable gain of 32, 64 and 128.
On-chip voltage regulator circuit can provide power directly to the external sensor and the chip A / D converter.
On-chip clock oscillator requires no external components , if necessary, can also use an external crystal or clock.
Automatic power on reset circuit.
simple digital control and serial communication : All are controlled by the input pin , the chip registers without programming.
selectable output data rate of 10Hz or 80Hz.
simultaneous rejection of 50Hz and 60Hz power interference.
Note: Module's DO-port, CK-port connect with single-chip, just a two-wire serial of data line and a clock line, not 232 serial protocol of computer, nor is I2C, SPI protocol.
Blue
![https://pg-cdn-a2.datacaciques.com/00/NDAy/22/09/17/vx5395q58j8t7380/9c27c9f1a76d512a.jpg](https://pg-cdn-a2.datacaciques.com/00/NDAy/22/09/17/vx5395q58j8t7380/9c27c9f1a76d512a.jpg)
Features:
1. Using high-quality materials, the quality is guaranteed
2. With pin header
3. The appearance of the product is exquisite and small
4. High precision
5. The module uses 24 hx711 high precision A/D converter chip
Product Description:
This module uses 24 hx711 high-precision A/D converter chip, which is specially designed for the design of high-precision electronic scales, has two analog input channels, and integrates a 128 times programmable gain amplifier. The input circuit can be configured as Provides bridge-type pressure bridges (e.g. pressure, load cell mode), ideal for high-accuracy, low-cost front-end sampling modules.
Product parameters:
Two optional differential input channels
On-chip low noise active PGA with selectable gains of 32, 64 and 128
Chip Power Regulators for Analog Load Cells and ADC Power Supplies
Chipless Oscillator External Components with Optional External Crystal
power-on reset chip
Simple digital control and serial interface: pin commands, no programming required
10SPS or 80SPS output data rate optional
Simultaneous suppression of 50 and 60Hz supply current consumption, including on-chip analog supply regulator: <1.5mA for normal operation, <1uA for power down
Operating supply voltage range: 2.6-5.5 V
Operating temperature range: -40°- 85°
Purple
![](https://pg-cdn-a2.datacaciques.com/00/NDAy/22/09/17/vx5395q58j8t7380/4173f636c71e7456.jpg)
Features:
711 is a 24-bit A/D converter chip specially designed for high-precision electronic scales. The required peripheral circuit has the advantages of high integration, fast response, strong anti-interference, etc., which reduces the cost of the whole electronic scale and improves the performance and reliability of the whole machine. The interface and programming of the chip and the back-end MCU chip are very simple, all control signals are driven by pins, and there is no need to program the internal registers of the chip. The input selection switch can arbitrarily select channel A or channel B, and its internal low-noise programmable amplifier connected, the programmable gain of channel A is 128 or 64, the corresponding full-scale differential input signal amplitude is ±20mV or ±40mV, channel B is a fixed gain of 32, which is used for system parameter detection. The voltage power supply can directly provide power to the external sensors and the A/D converter in the chip. No additional analog power supply is required on the system board. The clock oscillator in the chip does not require any external devices. The power-on automatic reset function simplifies the initialization of the boot. process.
Product parameters:
Two optional differential inputs
On-chip low noise programmable amplifier with selectable gains of 64 and 128
On-chip voltage regulator circuit provides power directly to external sensors and on-chip A/D converters
The on-chip clock oscillator does not require any external components, and an external crystal or clock can also be used if necessary
Power-on automatic reset circuit
Simple digital control and serial communication: all controls are input by pins, and the on-chip registers do not need to be programmed
Selectable output data rate of 10Hz or 80Hz
Simultaneous suppression of 50Hz and 60Hz power disturbances
Power consumption (including regulated power supply circuit): Typical operating current: < 1.7mA, power-off current: < 1μA
Operating voltage range: 2.6 ~ 5.5V
Operating temperature range: -20 ~ +85℃
16-pin SOP-16 package