Details
Product Features:
The INA226 is a current shunt and power monitor with an I2C™ or SMBUS compatible interface.
The device monitors both the parallel voltage drop and the bus supply voltage.
Programmable calibration values, conversion times and averages are used in conjunction with an internal multiplier to allow direct reading of current in amps and power in watts.
The INA226 senses current on a common-mode bus voltage that can vary from 0 V to 36 V, independent of the supply voltage. The device is powered from a single 2.7 V to 5.5 V supply with a typical power consumption of 330 µA.
The device is rated to operate over the -40°C to 125 \ xC2°C temperature range and has up to 16 programmable addresses on the I 2 C compatible interface.
The INA226 is a current shunt and power monitor with an I2C™ or SMBUS compatible interface.
The device monitors both the parallel voltage drop and the bus supply voltage.
Programmable calibration values, conversion times and averages are used in conjunction with an internal multiplier to allow direct reading of current in amps and power in watts.
The INA226 senses current on a common-mode bus voltage that can vary from 0 V to 36 V, independent of the supply voltage. The device is powered from a single 2.7 V to 5.5 V supply with a typical power consumption of 330 µA.
The device is rated to operate over the -40°C to 125 \ xC2°C temperature range and has up to 16 programmable addresses on the I 2 C compatible interface.
Product parameters:
Measured voltage:0 V to 36 V (negative voltage cannot be measured)
Measuring current:-20 A to +20 A
Bi-directional correspondence → current can be detected from both high and low end
Supply voltage:2.7 V to 5.5 V
Interface:l2C
I2C address:16 can be set by solder joint setting
Input detuning voltage:±10μV
Accuracy:1% earth
Resolution:16 bits (current:1.25mA, voltage:1.25mV)
Current consumption:1mA or less
Size:20mmx27mm(fixed hole 3mm)
Measuring current:-20 A to +20 A
Bi-directional correspondence → current can be detected from both high and low end
Supply voltage:2.7 V to 5.5 V
Interface:l2C
I2C address:16 can be set by solder joint setting
Input detuning voltage:±10μV
Accuracy:1% earth
Resolution:16 bits (current:1.25mA, voltage:1.25mV)
Current consumption:1mA or less
Size:20mmx27mm(fixed hole 3mm)
Instructions for use:
VCC:Power input 2.7-5.5V
GND:Power supply negative
SDA, SCL: lIC bus data and clock signal line
ALERT:Multi-function alarm output
AO, A1:IIC address line
VCC:Power input 2.7-5.5V
GND:Power supply negative
SDA, SCL: lIC bus data and clock signal line
ALERT:Multi-function alarm output
AO, A1:IIC address line
Caution:
*VIN power supply positive terminal to measure voltage, CND power supply negative terminal to measure voltage, VOUT to measure current input and output, this module can only measure 0-36V DC power supply, current can not exceed 20A maximum, VCC voltage 2.7-5.5V, GND-GND, more parameters can refer to the datasheet.
*VIN power supply positive terminal to measure voltage, CND power supply negative terminal to measure voltage, VOUT to measure current input and output, this module can only measure 0-36V DC power supply, current can not exceed 20A maximum, VCC voltage 2.7-5.5V, GND-GND, more parameters can refer to the datasheet.
Product List:
1x Module(Pin Soldered Or Not Soldered)
Copyright©2018 datacaciques
Top & Fast Shipping！
Get The Right At The Right Price！
DC 0-36V Measure INA226 Step Up / Down Current Voltage Monitoring Sensor Module
DESCRIPTION
Product Features:
The INA226 is a current shunt and power monitor with an I2C™ or SMBUS compatible interface.
The device monitors both the parallel voltage drop and the bus supply voltage.
Programmable calibration values, conversion times and averages are used in conjunction with an internal multiplier to allow direct reading of current in amps and power in watts.
The INA226 senses current on a common-mode bus voltage that can vary from 0 V to 36 V, independent of the supply voltage. The device is powered from a single 2.7 V to 5.5 V supply with a typical power consumption of 330 µA.
The device is rated to operate over the -40°C to 125 \ xC2°C temperature range and has up to 16 programmable addresses on the I 2 C compatible interface.
The INA226 is a current shunt and power monitor with an I2C™ or SMBUS compatible interface.
The device monitors both the parallel voltage drop and the bus supply voltage.
Programmable calibration values, conversion times and averages are used in conjunction with an internal multiplier to allow direct reading of current in amps and power in watts.
The INA226 senses current on a common-mode bus voltage that can vary from 0 V to 36 V, independent of the supply voltage. The device is powered from a single 2.7 V to 5.5 V supply with a typical power consumption of 330 µA.
The device is rated to operate over the -40°C to 125 \ xC2°C temperature range and has up to 16 programmable addresses on the I 2 C compatible interface.
Product parameters:
Measured voltage:0 V to 36 V (negative voltage cannot be measured)
Measuring current:-20 A to +20 A
Bi-directional correspondence → current can be detected from both high and low end
Supply voltage:2.7 V to 5.5 V
Interface:l2C
I2C address:16 can be set by solder joint setting
Input detuning voltage:±10μV
Accuracy:1% earth
Resolution:16 bits (current:1.25mA, voltage:1.25mV)
Current consumption:1mA or less
Size:20mmx27mm(fixed hole 3mm)
Measuring current:-20 A to +20 A
Bi-directional correspondence → current can be detected from both high and low end
Supply voltage:2.7 V to 5.5 V
Interface:l2C
I2C address:16 can be set by solder joint setting
Input detuning voltage:±10μV
Accuracy:1% earth
Resolution:16 bits (current:1.25mA, voltage:1.25mV)
Current consumption:1mA or less
Size:20mmx27mm(fixed hole 3mm)
Instructions for use:
VCC:Power input 2.7-5.5V
GND:Power supply negative
SDA, SCL: lIC bus data and clock signal line
ALERT:Multi-function alarm output
AO, A1:IIC address line
VCC:Power input 2.7-5.5V
GND:Power supply negative
SDA, SCL: lIC bus data and clock signal line
ALERT:Multi-function alarm output
AO, A1:IIC address line
Caution:
*VIN power supply positive terminal to measure voltage, CND power supply negative terminal to measure voltage, VOUT to measure current input and output, this module can only measure 0-36V DC power supply, current can not exceed 20A maximum, VCC voltage 2.7-5.5V, GND-GND, more parameters can refer to the datasheet.
*VIN power supply positive terminal to measure voltage, CND power supply negative terminal to measure voltage, VOUT to measure current input and output, this module can only measure 0-36V DC power supply, current can not exceed 20A maximum, VCC voltage 2.7-5.5V, GND-GND, more parameters can refer to the datasheet.
Product List:
1x Module(Pin Soldered Or Not Soldered)
SHIPPING
Please Make sure your Ebay Address is 100% right.
We maintain high standards of excellence and strive for 100% customer satisfaction!
Feedback is very important to us. We request that you keep in touch with us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.
PAYMENT
Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
RETURN
Please contact us first if you have any problems/questions/concerns. We will be happy to resolve any issues you may have in a cordial and friendly manner.
---------------------------------------------©Copyright Gogaviinse. All Rights Reserved.--------------------------------------