Autel PowerScan PS100 Electrical Automotive Circuit Tester Tool 12V/24V AVOmeter
Autel PowerScan PS100 Power Circuit Probe Kit, 12V 24V Automotive Circuit Tester, Car Electrical Diagnostic Tool, AC DC Resistance Voltage, Short Finder, Continuity/Probe/Signal Test
About this item
- 🥇【2023 ALL-IN-ONE POWER CIRCUIT TESTER KIT---ACCURATELY】Autel PowerScan PS100 is most accurate power circuit probe tester yet, with 160x128 TFT display test all 6-30 volt vehicle electrical systems. Autel PS100 supports voltage&polarity test, continuity test, signal circuit test, components activate, check bad grounding, locate short circuits, circuit breaker protection, etc. Intuitive interface with ergonomic design makes PS100 be best gift for all novice drivers or pro circuit repairers.
- 🥇【FOUR WORKING MODE---INTUITIVE&EASY】Four working modes make circuit detection more simple:DC Voltage, AC Voltage, Resistance, Tone On/ Off. DC Voltage mode can read DC voltage with 0.1V resolution; AC Voltage can read Max & Min voltage, frequency and duty cycle quickly; Resistance mode can read resistance between tip and auxiliary ground wire. Unique Tone On/Off Design is really useful when working in bright areas, it can judge the circuit voltage according to the volume of the sound.
- 🥇【COMPONENT ACTIVATION】The component activation feature is specially designed to troubleshoot on/ off-board electrical equipment. By activating the signal generated by the component, you can accurately judged whether the component is intact, such as blower motor, power window motor, windshield wiper, rear window defroster, lights, radiator fans, fuel injectors, etc. Autel PS100 circuit tester automotive tool can activate component in your hand/ in the vehicle/ with ground etc.
- 🥇【INSTANT IDENTIFY POLARITY】Autel PS100 instantly checks component continuity and quick identifies positive, negative and open circuits. When the positive terminal is connected, the red LED lights up along with beep sounds. When the negative terminal is connected, the green LED light up along with a low tone. If it is an open circuit, neither of LED light will not light. The indicator light is a considerate working guide to facilitate the smooth operation of detection.
- 🥇【CONTINUITY TEST】Autel PS100 Automotive Circuit System Tester can perform continuity test to judge whether the circuit has continuity. Two ways to test continuity: ✅1: In resistance mode, if the resistance is 0.0Ω and the LED lights up, it means continuity. ✅2: Power up the connection using the power switch, if the circuit brea-ker tr-ips, that means the resistance is low and there is continuity.
- 🥇【OVERLOAD PROTECTION, QUICK SELF-TEST】This Electrical System Probe Tester Autel PS100 has a built-in short circuit protection. When overloaded, built-in internal short circuit will automatically trip to ensure the safety of users and prolong the service life of the tester. In order to protect your components, the car circuit tester can also perform a quick self-test. After flipping the switch forward or backward, the LED light and tone will respond to quickly check its actual operating status.
- 📢【20FT EXTENSION CABLE, BUILT-IN FLASHLIGHT】Autel PS100 PowerScan circuit tester comes with extra 20ft extension cable allowing you to access any position of the vehicle and test it. The built-in flashlight is convenient for detection, even in the dark or dim environment, it can provide the best view for who need to work in night.
- 🥇【1-YEAR WARRANTY, PERFECT SERVICE】Autel PS100 provides one-year warranty, and supports 30 days no reason to return. Autel Direct store has been engaging in Autel brand for several years, aiming to offer top-ranking products with best service.
Product Description
Autel PowerScan PS100---Most Accurate Power Circuit Probe Kit
Autel PowerScan PS100---Revolutionary Circuit Tester
Autel PowerScan PS100 Tool is the most revolutionary circuit tester to date. Featuring AVOmeter, test light, built-in flashlight, short circuit indicator, relay/ component tester, continuity tester and bad ground indicator, the PowerScan 100 is truly the ultimate in power and affordability, allowing users to check circuitry in one single step.
Autel PS100 Car Circuit System Diagnostic Tool can quickly and accurately diagnose the electrical system, solve problems such as circuit short circuit, open circuit, etc., which is an essential circuit scanner for every technician.
Autel PS100 Circuit Tester Kit--- Do Everything For You
- DC voltage range : 0-65V +1 digit; Resistance range : 0–200 KΩ; Frequency response of tone passage: 0Hz to 10Khz.
- Performs multi-service including power injection, measurement, ground testing, polarity checks, continuity testing and components activation
- Easy to read AVOmeter allows you to read voltage, current and resistance at the fingertip
- Component activation with a flip of the power switch,
- Instantly identifies positive, negative and open circuits
- Test bad ground contacts instantly, allowing you to follow and locate shorts fast without wasting fuses
- Instantly checks continuity of switches, relays and diodes
- Circuit breaker protected
- Extra 20ft (extendable) cable provides excellent accessibility to test along the vehicle
- Built-in Flashlight, work in the dark
- Simple button design
More Useful Features, Give You Try
Autel PowerScan PS100 has rich functions, please check the following introduction:
- 4 modes to diagnose the electrical system: DC voltage, AC voltage, resistance, diode.
- Voltage & Polarity Test: According to the LED light and sound after the probe tip touches the circuit, it can accurately judge the positive, negative, and open circuits.
- Continuity Test: While the tool is in Resistance mode, using the probe tip with chassis ground or the auxiliary ground lead, continuity can be tested on wires and components attached or disconnected from the vehicle’s electrical system.
- Signal Circuit Test: When the vehicle has a fault code, in order to quickly determine whether the fault is caused by a certain sensor circuit, you can use this tool to quickly draw a conclusion.
- Find Short Circuit: A short can manifest itself as a blown fuse or a tripped electrical protection device. Use the probe tip to activate and energize each fuse contact. The contacts that trip the circuit breaker are shorted.
- Find Bad Ground: Probe for suspected ground wires or touch probe tips. If the breaker has tripped, the circuit is most likely grounded.
- Activate Component in your hand/ in the vehicle/ W/Ground
- Test Trailer Lights and Connections: Check function and orientation of connectors and trailer lights
- Red/Green Polarity Indicator: The red/green polarity LED illuminates when the probe tip voltage matches and is within ±0.8 volts of the battery voltage. It is additional information that may be of value to a technician.
|
|
|
|
|---|---|---|---|
DC VoltageWhile the tool in this mode, contact the probe tip to a circuit, then the LCD display will read the DC voltage with a resolution of 0.1 volt. | AC VoltageWhile the tool in this mode, contact the probe tip to a circuit, then the LCD display will read the Max. voltage, the Min. voltage, frequency and duty cycle. | ResistanceWhile the tool in this mode, contact the probe tip to a circuit, then the LCD display will read the resistance between the tip and auxiliary ground lead. | Tone On/ OffWhile the tool in this mode, just do a quick press of the mode button to toggle the tone on or off. While quickly pressing (a quick press and release) the mode button, if a short high beep is heard, this means the audio tone is turned on. If a short low beep is heard, the audio tone is turned off. |
20ft Extension Cable
20ft Extension Cable:
- Autel PS100 itself has an extra-long 20ft cable, considering the volume of 12V-24v vehicles such as ships and trucks, we have additionally equipped with extra 20FT extension cable for emergencies.
- With the 20FT extension cable, you can freely test the condition of any vehicle circuit without moving the device because the cable is not long enough.
Autel PS100 Circuit Tester has two power supply methods:
- 1. Vehicle battery power supply
- 2. Ciga-rette li-ghter power supply
Quick Self-Test:
- Before you test a circuit or component, be sure your tool is in good order by doing a quick self-test.
- With the tool connected, perform a quick self-test. The power switch is a momentary rocker switch located on the tool's body. Flanking the switch are positive and negative markings. Press the Power Switch forward to activate the tip with a positive voltage. The Red LED should light and the LCD display will read the battery voltage. If the tone feature is turned on, a high pitched tone will sound. Let go of the power switch and the LED will turn off and the high tone will cease. Press the Power Switch rearward to activate the tip with a negative voltage. The Green LED should light and the LCD display will read the „0.0V‟ (ground). If the tone feature is turned on, a low pitched tone will sound. Let go of the power switch and the LED will turn off and the low tone will cease. Your tool is working correctly and is now ready for use.
| DC voltage range | 0-65V +1 digit |
| Resistance range | 0 – 200 KΩ |
| Frequency response of tone | 0Hz to 10Khz |
| Circuit Breaker Rating current | 1 – 10 Amp |
| External Power | 12.0 or 24.0 V power provided via vehicle battery |
| Display | TFT color display (160 x 128 dpi) |
| Package Including | 1* PowerScan PS100 1* 20ft. extension cable 1* Rugged blow molded case 1*Probe tip 1* Battery clips 1*Ciga-rette lig-hter adapter 1*User's Manual |
