Feature:

1. On the basis of the original specifications, perfect match for N54 F02/E70 3.0L Twin Turbo Engines.
2. The cylinder head cover is usually called the valve chamber cover. Its function is to seal the parts of the valve mechanism and prevent dust from contaminating the oil or dust from entering and accelerating the wear of the parts of the valve mechanism.
3. The valve chamber cover has an oil port and a crankcase vent pipe interface, and the cover is made of alloy casting or stamping of thin steel plate. The valve chamber cover gasket is installed on the joint surface with the cylinder head.
4. The valve cover is mainly connected with the cylinder head of the engine. The camshaft is installed under the valve cover and sealed with some parts of the intake mechanism on the cylinder head to ensure the normal operation and lubrication of the engine's driving mechanism, and dustproof.
5. Adopting high quality ABS to made, with super corrosion resistance, oil resistance characteristics, quality assurance, high reliability.

Specification:

Item Type: Engine Valve Cover
Material: ABS
Colour: Black
OEM: 11127565284
Fitment:
For N54 F02/E70 3.0L Twin Turbo Engines
For 335xi 2007-2008
For 335i 2007-2010
For 535i X6 2008-2009
For 135i 2008
For Z4 2009-2014
For 535i 335i 2009-2010
For 740i 740Li 2011-2012
For 335is 2011-2013
For 1 Series M 2011

How to Use:
1. Before installation, please pay attention to the product sealing rubber gasket (the sealing rubber gasket is flatly inserted into the corresponding sealing groove), and the sealing rubber gasket in the unsealed area may be loose or uneven after being installed in the slot
2. Clean first to confirm whether there are impurities or dirt inside the sealing groove of the uneven position, if there is, please clean it carefully and install the sealing rubber gasket again.

The sealant can be used for local positioning. Pay special attention to applying a small amount of sealant to the two sides or edges of the seal groove and then install the sealant gasket to ensure that the sealant gasket is flatly inserted into the corresponding sealing groove before installing and removing excess sealant.

4. It must be noted that the glue is only used to fix the sealing pad. When glue is needed, only a small amount of sealant needs to be applied to the two sides or edges of the sealing groove to fix it. If there is a large area of glue Circumstances will also affect the sealing functionality of the product.
5. When installing the spark plug tube of this product, please confirm whether the spark plug tube is equipped with a sealing ring, and then directly install it into the corresponding groove ring of the product after confirming it is complete (after installing, confirm whether the installation is in place, and there is no looseness and  phenomenon, it is qualified, otherwise It is abnormally unqualified, PS: No need to glue and fix). If the spark plug tube is directly installed into the product groove ring without the sealing ring installed, the phenomenon of looseness, unstable installation and  will occur.
6.When the valve cover and the cylinder block are placed together, it is recommended to raise the valve cover again to a height of about 2cm/0.79in, and use your fingers to wrap around the valve cover to confirm that the sealing rubber gasket is not offset and detached, and then reassemble it, (This process is to prevent the sealing rubber gasket from deviating or loosening during the installation process)
Detection:
1. Start the engine and check if there is abnormal noise, unstable idle speed or oil leakage
2. If you find abnormal noise or unstable idling, open the oil cap again, the abnormal noise will disappear. This problem is caused by the valve cover and the cylinder block not being completely sealed. If this happens, please loosen the valve cover screw or take it out, confirm that the rubber gasket of the valve cover is in place and reinstall it.

Package List:

1 x Engine Valve Cover

1 x Gasket

Note: