15KV High Frequency DC High Voltage Ignition Generator Inverter Boost Step-Up
International Buyers Please Note: -
Import duties, taxes and charges are not included in the itemprice or
shipping charges. These charges are the buyer responsibility.
- Please check with your country customs office to determine what these additional costs will be prior to bidding/buying.
We will carefully test every item before shipment.
The quality is guaranteed!
❤ If the products have any problems, please contact us before you give the bad feedback. Thanks for your understandings.❤
Description Note: This item is DIY Kit, not assembled. default with one PCB board.
Features: ◦This product is a booster coil production suite, the circuit is simple and reliable, with a professional line drawings, electronic research convenience enthusiasts
◦Uses: high school science experiment, electronic equipment, negative ion generator, scientific small production. This circuit is generated when the stable high frequency arc, high temperature, can easily ignite combustible materials, so it was called the plasma lighters
Parameter: ◦15KV transformer outside dimensions of approximately: 27×16×21mm ◦Input voltage: DC 3.7V-4.2V (limit 12v, easy to damage not recommended, this transformer is equally applicable to 12V input voltage, but requires a corresponding increase in the base of the feedback resistor to about 150Ω ~ 1.5KΩ, its resistance should be large to replace a small adjustment, or burned transistor or transformer) ◦Input Current: <2A ◦Output voltage: approximately 15KV (please pay attention to safety when used) ◦Output Current: ≤0.4A ◦High voltage bipolar ignition distance: ≤0.5 cm
◦When the product input termination 3.7V-4.2V power supply, the secondary high voltage output is not connected to high-voltage rectifier diodes and capacitors, output terminals levels ≤1.5cm long can produce purple high temperature arc, no crackling, but the temperature is very high , you can easily and instantly point cigarette paper, or even very thin wire burned Sparks (such as junior high school chemistry experiment thin wire in oxygen combustion scene, but not as good as oxygen so intense.)
Transformer structure: There are two primary windings, a primary winding, a feedback winding, the secondary output of high pressure. Other: 15KV transformer designed for maximum output, limit output can not exceed 15KV, is one centimeter arc, a higher output voltage is likely to damage the transformer.
PCB board size: 4.2CM * 3.2CM * 0.16CM;
Installation Notes: 1). With the PCB board parts better production, in which the transformer line of thick line and thin line, this should pay attention to the other components by the board of silk symbols and parameters of welding on the line. Transformer board has done three pads, in which the middle of the pad hole is relatively large, the hole at the same time welding a thick enameled wire and a thin enameled wire, thick enameled wire and fine enameled wire do not use the same side, such as with the left Thick lines and the right side of the thin wire into or with the left side of the thin line and the right side of the thick line welding into, in short, do not use the same side of the thick lines and thin lines can be.
2). In order to prevent the output 2-wire distance too far, resulting in no-load, you can weld a 3P pin at the output.
3). After the success of the production, if the output access to a high-voltage capacitor and three high-voltage rectifier composed of voltage doubler circuit, you can produce DC high voltage, you can make anion generator, wiring diagram is as follows:
Package Include: 15VKE = 1 type step-up transformer x1 PCB Board X 1 120 ohm resistance X 1 UF4007 ultra-fast recovery diode X 1 N20 transistor X 1 Heat sink X 1 M3 * 6 screws X 1 Boat switch X 1 3-Pin X 1
We accept PayPal only.
All major credit cards are accepted through secure payment processor PayPal.
Payment must be received within 7 business days of auction closing.
If
you have bought multiple items from me, you can send me one payment for
all the items instead of paying for them individually. When you click
the Pay Now button, eBay will automatically determine if there are other
items you have won or purchased from me and will combine them for your
review.
Only through PayPal
1.We ship to eBay address. Please make sure your address in ebay is matched with your shipping address before you pay
2.Please
indicate your personal requirement, such as colors, packages, value of
declaration etc, at paypal's message when you pay to us.
3.We will NOT be responsible for any delay during delivery including but not limited to customs postage checking, strike, force majeure etc.
4.As a buyer, it is your duty to pay the tax when you make a order from abroad. Our price does not include taxes, VAT, or other hidden charges.
Return & Refund Refund
or replacement request is available only the requests within 1 week
after parcel received & returning the item as the same condition as
received.
Please
contact us to request a return authorization. Your name, auction
number, and reason for return should be included in the email. All items
returned must contain all original packaging materials.
Please
repack the item carefully. Items returned will be tested and a new
replacement will be shipped to the buyer immediately when found
defective. In the event that a suitable replacement is not available
then a refund will be issued. Shipping, handling and insurance fees are
non refundable.
If
the item is found non-defective, the item will be sent back to the
buyer at buyer's expense. Items returned without RMA number will be
refused and returned to the sender. Buyer is responsible for All Return
Postage and Shipping Charges. Buyer is responsible for additional
shipping costs for items that are returned refused and/or undeliverable.
We do not accept any returns without an authorization number on the box
or label it is being returned in.