Skylight 500x500, single acrylic, blackout blind, and flynet screen
The AutoShield skylight dome roof vent is an ideal accessory for the motorhome, camper van, or house box which requires additional ventilation and light. It’s also ideal for venting small spaces. Made from superior quality impact and UV resistant materials supplied with blackout blinds and flynet screens.
Specification:
Ideal for campervans/vans/motorhomes/showers/sanitation areas /outbuildings/sheds/barn
*Easy operation with gas lift struts.*Maximum opening to an angle of 60° with three opening positions to 150 cubic center meters of permanent ventilation. Product code : SKY.400x400Cut out size： 402mm*402mmAbove the roof ：106mmWall thickness： 30mm-50mm
R angle: R10
Weight：4.3kgs
Overall：500mm*500mm
*Has a light green tint
*Interior frame with black-out blind and fly net screen.
*Double-glazed dome top.
Instructions to fit:
1-Place the internal cap (garnish) on top of the roof and draw a template using a felt tip, then add another 5mm to the top and left side.
2-Drill pilot holes in each corner and cut along the template line. Be certain to avoid ribs, braces, and electrical wiring (internally).
3-Check that the internal cap fits through the aperture If not, cut out the opening as needed and then smooth down any rough edges and primer the exposed with metal oxide paint.
4-Make a wooden frame around the aperture to the thickness of the interned finish depth required, taking into account the roof ply and lining.
5-Glue the frame with Shield Stick and Seal (polyurethane) clap in place and allow the adhesive to set.
6-Screw the internal cap to the timber frame and seal around the lip from the top of the roof using flexible putty or Sikaflex.
7-Place the external vent over the lip of the internal cap and mark the screw holes with a center punch. Then remove the vent from the roof and drill all screw hole locations with a 1/16’’ pilot hole, and seal with primer paint.
NOTE: If installing a power or lighted vent, provide a power source of 12 volts DC, using an 18-gauge wire.
8-Place putty strips/ Sikaflex flex bead around the opening on the roof ½’’ (1.27cm) from the edge of the opening. (Be sure putty strips cover the entire area to be sealed.) Use double layers of putty strip or extra Sikaflex if necessary, to seal ribbed areas.
9-Insert vent into opening on top of putty strips.
10-Use a screwdriver or nail to locate and line up corner drilled holes with the corner screw holes in the vent frame. CAUTION: Install vent with lid hinge side toward the front of the vehicle. Screw corner screws first to hold the vent in place then screw all remaining vent mounting screws. Tighten just enough to compress putty tape. Over-tightening may cause Plastic Base Vents to crack.
11-Using the appropriate roof coating for your roof surface, coat screw heads, and vent frame edge and seal around the frame if necessary.
12-Your installation is complete.
Orders are shipped Mon-Fri, Orders received after 9:30am or on weekends are dispatched the following working day.
Dispatch time: 1 Working day.
Delivery time: 2-5 Working days
Express Delivery time: 1 Working day
All items are stored in and dispatched from the United Kingdom.
We cannot guarantee address changes after purchase, as we use an automated shipping system.
Please note that some locations in the UK may carry a postage surcharge. If you are in one of the following postcodes; BT, PA, KW, IV, HS, AB, IM, ZE, GY, JE, DD, PH, KA, PO, ZE, you may double check postage costs using the postcode checker in the "postage and payments" tab of the item description. Please be aware service to the aforementioned postcodes can take an additional 1-2 days including our express service.
If there are any issues with your order, or you are not happy with your item, please don't hesitate to contact us through the message system prior to leaving feedback. We endeavour to ensure transactions are smooth and our friendly staff will always offer simple solutions to any problems