The WOW101 is a universal decoder for locomotives with DCC-ready 9-pin plugs, or which cannot accommodate a motherboard or WOWKit. This decoder may be hard-wired or plugged directly into any locomotive with a 9-pin JST plug. The WOW101 is compatible with any T-Series harness, and also includes an auxiliary harness for attaching your speaker, AUX input, Keep Alive®, and for the additional lighting functions (F3 and F4). The WOW101-KA-Diesel decoder

includes a KA3 Keep Alive® included on the auxiliary harness.

Includes 19 Prime Movers This decoder includes:

GE ES44CW, ALCO 539-T, Baldwin 8-VO, Baldwin 606-A, Baldwin 606-NA, Baldwin 608-A, EMD 567 roots blown, 567 turbo, 645 turbo, three different 645 non-turbo's (roots blown), 710 prime mover sounds, as well as two ALCO 251's, ALCO 244, GE FDL16, and two different 7FDL16's.

NOTE: WOW101 decoders do not have on-board resistors. If you are going to use LED lighting with this product, you must include external resistors.

For a complete list of sounds, check out the "Sounds List" under the "Documents" tab.

• CD-Quality Sound: TCS' world-renowned CD-quality sound. 16 Bits of resolution at 44.1kHz sample rate.

• Keep-Alive®: Included on-board for smooth, stutter-free operation.

• Back EMF Load Compensation: Provides superior slow speed control and high performance under load.

• Quiet Drive: Super-quiet motor control for "buzz" free motor performance.

• Variable Momentum: Allows you to make custom acceleration and deceleration curves.

• Incandescent Bulb Support: This decoder can be used with 12 Volt bulbs.

• Function Remapping: Buttons 0 through 12 may be used to control the lighting functions of this decoder.

• Programmable Lighting Effects: Choose from 20 separate user-programmable lighting effects!

• Dimmable Brightness: Configure multiple different brightness levels for your LED's or incandescent bulbs.

• Decoder Lock: Feature which prevents accidental/unwanted programming while activated.

• Airwire™ Compatible: Fully compatible with Airwire™ operation.

• Audio Assist®: TCS exclusive auditory feedback programming system. Program your decoder without the need to memorize CV's!

• User-Loadable Speed Tables: Configure custom speed curves and set speed limits.

• Throttle Modes: Choose from multiple throttle modes to meet your operating needs.

• Proto Notch™: A WOWSound original feature which uses TCS’ exclusive auto-adjusting BEMF technology to automatically choose the active notch sound. Prototype Mode also offers dynamic sound volumes which accurately model the real-life equivalent. Also includes pre-programmed acceleration and deceleration values.

Specifications:

Interface Type: Hard-Wire or Direct-Plug (9-Pin JST)

Dimensions (L x W x H): 1.35" x 0.658" x 0.22" or 34.29mm x 16.72mm x 5.59mm

Scale: HO Scale

Continuous/Peak: 1.3/2.0 Amp

Total Functions: 6

Function Rating: 100 mA

12V Outputs 6

Speaker Selection

• This decoder is optimized for 8 Ω speakers (not included).

• This decoder uses and audio amplifier capable of supplying up to 2 Watts of power to an 8 Ohm load at maximum volume. An 8 Ohm speaker with a 1 Watt minimum power rating is recommended for use with this decoder as it comes out of the package. If you are using an 8 Ohm speaker with a power rating of 2 Watts or less, you must reduce your master volume to prevent speaker failure or amplifier stress.

• The amplifier(s) on a WOWSound product can support speakers with impedance ratings as low as 4 Ohms. A reduction in impedance will require a higher power dissipation rating (more Watts) on said speaker. The minimum power requirement for a 4 Ohm speaker is 4 Watts. If you are using a 4 Ohm speaker with a power rating of 4 Watts or less, you must reduce your master volume to prevent speaker failure or amplifier stress.

• Speaker enclosures greatly increase speaker performance in most cases - improving the apparent volume by more efficiently directing the flow of air and reducing or eliminating destructive interference.