CNC ENGRAVING MACHINE parameters:
X, Y, Z Working Area: 400(Y)*295(X)*80(Z)mm
Outside dimension: 630*505*495mm(L*W*H)
Table size: 550(Y)*360(X)mm
Lathe structure: 6061/6063 Aluminium alloy
Max. Feeding height: ≤60mm
Drive unit:
X axis---SFU01204-4 Ball Screws
Y axis---SFU01204-4 Ball Screws
Z axis---SFU01204-4 Ball Screws
Sliding unit:
X axis---High intensity Chromeplate shaft
Y axis---High intensity Chromeplate shaft
Z axis---High intensity Chromeplate shaft
Stepping motor: 57 two-phase 3A 150N.cm
Spindle motor
(tips:1.The spindle motor must connect with the VFD.
2. It cannot directly connect with the supply voltage (220V).
3. Please don’t change the data setting of the VFD if you are not professional technicians, or it might damage the spindle motor.
Outside dimension: 65*158mm
Material: 304 stainless steel, Copper coil, Pressure cast aluminum pipe water jacket
VOLTS, current, power: AC220V, 50Hz, 5A, 0.8KW VFD
Spindle speed: 24000 rpm
Max working frequency: 400Hz
Principal axis collet: ER11collet, Standard configuration:6mm
Nut Model: ER11-A
Cooling: Water-cooling
Speed mode: By adjusting the VFD output voltage and operating frequency from 0-24000RPM
Lubrication way: lubricated by high grease
Repeat accuracy: 0.05mm
Spindle precision: radial beat acuities 0.03mm
Carving Instructions: G code / TAB files / nc file / NCC files
Software environment: windows XP / win7 32bits system
Maximum speed: 0-4000mm/min
Carving speed: 0-2500mm/min(different materials differ)
Friendly reminder:
The engraver will fit for MACH3 software.
installation tips:
The software perform better on the 32bites system computer.
Please close the firewall and antivirus software on the computer before DOWNLOADING AND installing the software.(This is very important)
Otherwise, the antivirus will regard the cnc software as virus and stop the installation.
PS:
Please don't update the software when installed, then it will not need the license Numbers.
Control box parameters:
Operating Voltage: AC 220V
Control unit: Toroidal transformer + PWM power supply module + TB6560 stepping motor drive
Command code: G code
Acceptable software: fit for Mach3
Protection: Emergency stop button
cnc engraving machine parameters:
X, Y, Z Working Area: 600(Y)*390(X)*120(Z)mm
Outside dimension: 865*680*570mm(L*W*H)
Table size: 770(Y)*490(X)mm
Lathe structure: 6061/6063 Aluminium alloy
Max. Feeding height: ≤100mm
Drive unit:
X axis---1605 Ball Screws
Y axis---1605 Ball Screws
Z axis---1204 Ball Screws
Sliding unit:
X axis---High intensity Chromeplate shaft
Y axis---High intensity Chromeplate shaft
Z axis---High intensity Chromeplate shaft
Stepping motor: 57 two-phase 3A 150N.cm
Spindle motor:
(tips:1. The spindle motor must connect with the VFD.
2. It cannot directly connect with the supply voltage (AC220V).
3. Please don’t change the data setting of the VFD if you are not professional technicians, or it might damage the spindle motor.)
Outside dimension: 65*158mm
Material: 304 stainless steel, Copper coil, Pressure cast aluminum pipe water jacket
VOLTS, current, power: AC220 /50Hz, 5A, 1.5KW VFD
Spindle speed: 24000 rpm
Max working frequency: 60Hz
Principal axis collet: ER11collet,Standard configuration :6mm
Nut Model: ER11-A
Cooling: Water-cooling
Speed mode: By adjusting the VFD output voltage and operating frequency from 0-24000RPM
Lubrication way: lubricated by high grease
Repeat accuracy: 0.05mm
Spindle precision: radial beat acuities 0.03mm
Carving Instructions: G code / TAB files / nc file / NCC files
Software environment: Windows XP/Win7, 32 bits system
Maximum speed: 0-4000mm/min
Carving speed: 0-1500mm/min(different materials differ)
Friendly reminder:
The engraver will fit for MACH3 software.
installation tips:
The software perform better on the 32bites system computer.
Please close the firewall and antivirus software on the computer before DOWNLOADING AND installing the software.(This is very important)
Otherwise, the antivirus will regard the cnc software as virus and stop the installation.
PS:Please don't update the software when installed, then it will not need the license Numbers.
Control box parameters:
Operating Voltage: AC220V
Control unit: Toroidal transformer + PWM power supply module + TB6560 stepping motor drive
Command code: G code
Acceptable software: fit for Mach3, EMC2
Protection: Emergency stop button
Model G---4Axis-6040-1500W
cnc engraving machine parameters:
X,Y,Z Working Area:600(Y)*390(X)*120(Z)mm
Outside dimension:865*680*570mm(L*W*H)
Table size:770(Y)*490(X)mm
Lathe structure:6061/6063 Aluminium alloy
Max. Feeding height:≤100mm
Drive unit
X axis:1605 Ball Screws
Y axis:1605 Ball Screws
Z axis:1204 Ball Screws
Sliding unit
X axis:High intensity Chromeplate shaft
Y axis:High intensity Chromeplate shaft
Z axis:High intensity Chromeplate shaft
Stepping motor:57 two-phase 3A 150N.cm
Spindle motor
(tips:1. The spindle motor must connect with the VFD. 2. It cannot directly connect with the supply voltage (AC220V). 3. Please don’t change the data setting of the VFD if you are not professional technicians, or it might damage the spindle motor.
Outside dimension:65*158mm
Material: 304 stainless steel, Copper coil, Pressure cast aluminum pipe water jacket
VOLTS, current, power: AC220V/60Hz, 5A, 1.5KW VFD
Spindle speed: 24000 rpm
Max working frequency: 400Hz
Principal axis collet: ER11collet, Standard configuration: 6mm
Nut Model:ER11-A
Cooling:Water-cooling
Speed mode: By adjusting the VFD output voltage and operating frequency from 0-24000RPM
Lubrication way: lubricated by high grease
Repeat accuracy: 0.05mm
Spindle precision: radial beat acuities 0.03mm
Carving Instructions: G code / TAB files / nc file / NCC files
Software environment: Windows XP/win7, 32 bits system
Maximum speed:0-4000mm/min
Carving speed:0-1500mm/min(different materials differ)
Friendly reminder: The engraver will come with MACH3 software(Free Version
If you followed the intsalation tips offered by us, it works like full version.)
intsalation tips:
The software perferm better on the 32bites system computer.
Please close the firewall and antivirus software on the computer before DOWNLOAD AND install the software.(This is very important)
Otherwise, the antivirus will regards the cnc software is virus and stop the installation.
PS:
Please don't update the software when installed, then it will not need the license Numbers.
Control box parameters:
Operating Voltage:AC220V
Control unit:Toroidal transformer + PWM power supply module + TB6560 stepping motor drive
Command code:G code
Acceptable software:fit for Mach3, EMC2
Protection:Emergency stop button
Model H---4Axis-6090-1500W
CNC Router engraving machine parameters:
Model: CNC6090GZ
Outside dimension: 1150*970*650mm(L*W*H)
Working platform size: 1045*720mm(L*W)
Frame Material:The whole machine used 6061 aluminum profiles
Max. Feeding height: ≤140mm(From base of Z axis to platform)
X, Y, Z Working Area: 900(Y)*600(X)*140mm(Z)
Sliding unit:
X axis:SFU1605 Ball Screws
Y axis:SFU1605 Ball Screws
Z axis:SFU1204 Ball Screws
Drive unit:
X axis: ø20 High intensity round rail,
Y axis: SBRø20 high-strength aluminum base rails
Z axis: ø12 high-strength round rail
Stepping motor: 57 two-phase 3A (with handwheels)
Driving Power for Stepping motor: AC220, 240W, out put: DC24V, 10A
Maximum Idle speed: 1500mm/min
Working Speed: 50-1500mm / min (different material with different speed settings)
Spindle motor: 1500W high-speed variable frequency spindle motor, ER11 chuck, with 6mm collet.
(tips:1. The spindle motor must connect with the VFD.
2. It cannot directly connect with the supply voltage (AC220V).
3. Please don’t change the data setting of the VFD if you are not professional technicians, or it might damage the spindle motor.)
Drive of Stepping motor: 0-3.5A adjustable four-axis drive
(TB6560AHQ chip, 24V power supply, 2,4,8,16 subdivision can be set, factory settings 8 subdivision)
Repositioning precision: ≤0.05mm
Cooling: Water-cooling
Speed: 0-24000r/m
Spindle precision: Radial runout ≤ 0.03mm
Carving command: G code / TAB file / nc file / NCC file
VFD: AC220V, 1500W, 0-400Hz (built-in control box)
USB Control box parameters:
Protection: Emergency stop button
Recommend software: fit for Mach3, EMC2
Communication interface: through USB PORT connect with computer
Software environment: Windows XP / win7 with 32 bit (proper computer system makes the software run, otherwise it will not work)
Input Volts: AC220V