Instructions

Mix Binder A with Filler B at a ratio of 2:1 (i.e. 1 ml Filler B with 2 ml Binder A ). Using the spatula provided stir well for about 2 minutes until all Filler B is dissolved into Binder A. Gap between BGA component and PCB should be clean (if BGA has been reworked then there should be no signs of flux. Rework with nitrogen is suggested). Keep the PCB in a vertical position. Using the spatula feed slowly the mixture into a BGA/PCB gap until all feed disappears into the gap. Continue feeding until mixture appears at the other end. Now keep the PCB horizontal making sure that the mixture arrears on all gaps. Wait for about 30 minutes and wipe all mixture located outside of the gaps making sure that air can get to the edges of the gap. Mixture needs 48 hours to cure. Store the PCB in a well ventilated area for 48 hours before installing any other component on it (heat sink etc) or placing it back to the system that it comes from. Attention! No electrical power should be applied on the PCB during the first 48 hours. When in liquid form, mixture is electrically conductive and permanent damage could be caused.

BGA COAT: Improve reballing & reflow repairs on GPU


Product Description


BGA COAT creates an interconnection between the BGA component and the PCB, plus a coating around the solder balls of the component. This product is now offered for use on repairs (reballing or reflow of GPU and other BGA components) of commercial electronics such as laptops, gaming consoles etc.


Advantages


BGA COAT compared to EPOXY adhesives that are used as under fills has the following advantages


1. It is non EPOXY and non toxic.

2. It can be applied without mechanical means by using only a spatula (provided in the packet)

3. It is commercially available for use in small workshops (EPOXY adhesives for under filling are available for industrial use only)

4. It has good thermal conductivity (higher than most thermal pads and thermal pastes). This results in equalizing the temperature in the base of the BGA component eliminating the chances of a problem because of partially overheating of the component.


Key features
BGA COAT creates an interconnect between the BGA component and the PCB. The component is strongly attached on the PCB and the chances of mechanical damage (such as after a drop test) is practically eliminated.
BGA COAT creates a coating around the solder balls of the component. The solder balls are protected from environmental effects such as humidity and oxidation and the chances of joint fracture is limited. Also the phenomenon of tin whisker growth is limited and the flow of solder from one joint to another.
BGA COAT has good thermal conductivity (higher than most thermal pads and thermal pastes). This results in equalizing the temperature in the base of the BGA component eliminating the chances of a problem because of partially overheating of the component. It can also create a direct connection between the base of the BGA component and the system's heat-sink. This way the temperature of the base of the BGA is reduced significantly.
BGA COAT while it cures, absorbs all the humidity that could be located under the component and around the solder balls. This way the solder balls are coated in a dry and well protected environment.
BGA COAT can be applied very easily by using only a spatula that is provided. Packaging includes everything that is needed for up to 100 repairs (packet contains enough material to produce around 70ml of BGA COAT. Most BGA components require around 0.5ml of BGA COAT to be placed under them).
BGA COAT can keep it's form and size for temperatures up to 250 degrees (Celsius).



Other Information
Payment PolicyPrice includes VAT 24%. If you are VAT registered in EU, please contact us before purchasing and we will offer a quote without VAT. Greek business customers should provide their business info in order to issue a commercial invoice. We only accept PayPal as a payment option for online orders.
Content 2 X 25ml (50ml in total) of liquid Binder A
1 X 25g of powder Filler B
1 X dispenser with measure indications (ml)
1 X spatula
1 X container box where the product should be stored
CleaningTools used for mixing and applying the coating can be cleaned with cleaning tissue paper before setting begins. After hardening, they can only be cleaned by mechanical means.
Shipping We offer 3 shipping options:

Small packets international - Air:
We use special airmail envelopes for 5th day delivery worldwide. In some countries customs delays could be expected. Most customers in Canada and USA receive these packets in about a week.

Standard international shipping with tracking number:
Typical shipping service letter post through post office registered mail. We will provide tracking details as soon as packet is shipping. Tracking systems is informed very slowly so in many cases customer could receive the packet before it can track it on line. Shipping time is 6 bussiness days worldwide. Customs delays could also be expected.

Expedited international shipping:
3 day shipping service through DHL express or other international currier depending on your location.

Protect from frost and dust. 
Storage Packing and Precautions12 months in unopened packing. 3 months in closed packing after opening.
This product is designed for professional use ONLY. It should be used only by technicians with experience on BGA component rework.
Must not come into contact with materials like pure Fe or Fe-free metals during storage. Protect from frost. Use protective gloves when mixing, eyes protection, and take usual precautions when handling chemical products like ventilation. The user is responsible for any improper use of the product. 
OfferingsSend us your feedback, comments and suggestions about BGA COAT and we double your next order of BGA COAT. We will send you one more packet of BGA COAT for each packet that you will order and pay. Example: if you order 2 packets we will send you 4 packets in total while you will only pay for two. Offer is for orders up to 5 packets. If you order more than 5 then only 5 additional packets will be sent for free. Offer can be used for each ebay user only one time and only on their second order. Feedback should be sent through ebay messaging system.
Collaborations We are looking for resellers worldwide. If you are interested in reselling our products in your region please contact us with your business info and web site and we will send you our reseller offer. K5 PRO has been sold to customers in more than 75 countries worldwide and it is already suggested as the best thermal pad replacement solution on all serious forums!

Awards

About Computer-Systems

Thank you for visiting ebay store of www.Computer-Systems.gr!

We are a notebook repair workshop in Thessaloniki Greece and we are offering repair services and spare parts from notebooks in lowest possible prices. Computer Systems laboratories offer repair and data recovery services since 2008. We are the only SME workshop coofunded by Greece and EU for scientific research on BGA rework methods and on Data recovery. Thanks to our research work we can offer the highest success rate on all our services for the lowest possible cost.

We also offer professional equipment, training, support and consumables for computer repair workshops. From single customers who want to repair just a broken iPhone to chain shops that want to set up a network of repair workshops, Computer Systems laboratories can offer the best complete solutions.

Price includes VAT 24%. If you are VAT registered in EU, please contact us before purchasing and we will offer a quote without VAT. We only accept PayPal as a payment option for online orders.

Greek business customers should provide their business info in order to issue a commercial invoice.

UK CUSTOMERS:

This item will be shipped to you from our UK stock through Royal mail and you have two options. Standard with tracking which takes around a week and expedited which takes 2-3 days.


USA, CANADA, AUSTRALIA customers:

This item will be shipped to you from our local stock in your country so there will be no customs delays. You have two options. Standard shipping with tracking which takes around a week and expedited which takes 2-3 days.


Rest of the world customers:

This item will be shipped to you from our production center in Thessaloniki, Greece. You have two options. Standard shipping with tracking which takes around a week to arrive and expdited which takes 2-5 bussiness days.

Please don't Hesitate to Contact us.
Message Us Via eBay Messaging Service

We are happy to assist you! Please message us for further assistance.

Click Here To Contact Us