Lumenier QAV250 "Fury" Power Distribution Board W/ TBS Core OSD Integration 2111
Quick Overview
The "Fury" power distribution board
("PDB") for the QAV250 Mini FPV Quadcopter. This PDB is packed full of
features and allows for the direction integration of the TBS Core OSD.
Details
Looking for a QAV250 Power Distribution Board (PDB) to get an
integrated FPV setup and simple R/C wiring? This board, nicknamed
"FURY", provides upgraded power distribution with current sensing,
filtered power to the A/V equipment and option to install a TBS CORE
module, while also adding rigidity to the airframe.
The ESCs are soldered to the the board (all wires), making the board
layout very tidy and modular. It is designed with the OpenPilot flight
controller in mind, requiring only two cables to install the flight
system and another two cables (included) to finish the FPV system.
In front of the board is a spot to install an optional TBS CORE
module. This provides separation between the FPV system and R/C flight
system - which is known to produce noise and cause video interference.
It also provides a simple and very handy OSD (On-Screen Display) to read
battery consumption, voltage and receiver signal strength. The board
can also be set up to work stand-alone (without CORE).
The camera and video transmitter plugs easily into the sockets with
the provided cables, there are also solder pads to connect wires
directly. Several auxiliary power ports make it easy to hook-up alarms,
beepers, video transmitters, etc.
It is made of the same high strength fiberglass-reinforced epoxy
laminate as the stock PDB. All the components are protected inside the
"cavity" on the QAV250 platform. Two additional mounting holes in the
front gives extra rigidity.
Designed and developed by ivc.no
Features
- Built to reduce clutter and make setup easy
- Direct replacement of original QAV250 PDB
- Speed controllers connect directly to the board - power and control!
- Only two wire harnesses needed when using OpenPilot and two for FPV equipment
- Power configuration jumpers to setup on-board power routing
- Additional capacitors to stabilize ESC sync.
- Optional TBS CORE module for separate voltage regulation and OSD read-outs
- On-board 50A current sensor
- BEC power filtered and load-balanced - connect multiple BECs in parallel
- Filtered video transmitter and camera power, in addition to CORE filtering
- LED indicators shows status of BEC and battery power
- Multiple auxiliary pads for for VTx, camera, beepers, alarms, etc.
- Provides good RF shielding for noise isolation
Specifications
- Revision: Rev. 2 May 2014
- Platform: Lumenier QAV250 quadcopter
- Speed controllers: 10-18A, approx. L29 mm x W18 mm x H7 mm
- Power outputs: filtered BEC power, filtered battery power, filtered TBS CORE power
- Current sensor: 50A
- OSD features: current consumption, battery voltage, up-counting
timer, RSSI (received signal strength indicator) - TBS CORE required!
- Shielding: ground pour shielding, TBS CORE RF shield
- Connectors: JST-SH 1.25mm sockets, 2.54mm solder pads, 2mm solder pads
- Status indicators: green BEC OK, blue battery OK
- Material: Fiberglass laminate board, 1.6mm, white finish
- Dimension: 149 x 49 x 15 mm
- Weight: 21 grams
Includes
- 1x QAV250 "FURY" PDB Board
- 1x OpenPilot Power Cable
- 1x Sony Board Camera Cable
- 1x ImmersionRC VTX Cable
- 2x Pin Headers 2.54mm for VTX/CAM
- 1x Pin Header 2mm for TBS CORE
Combine Shipping: We will happily combine shipping. On small parts it is the highest shipping plus $1 for each additional item. On parts orders of $50 or more shipping is $5.99. If you use the Ebay shopping cart you will receive the correct combine shipping rate.
We
will happily combine shipping. On small parts it is the highest
shipping plus $2 for each additional item. For combine shipping on
international orders please purchase the items without the Ebay shopping
cart, but don't pay until we send an adjusted invoice.
Please contact us about combine shipping on larger items.
International Shipping: