eBay

1000KV Step Up High Voltage Pulse Inverter Arc Generator Ignition Coil Module C

Recommended Power Supply(not included): Single 3.7V lithium battery or two 18650 batteries, phone battery(>2000mAh, protection board should be removed), NiCd/Ni-MH battery pack, 4V or 6V -acid battery(6V can provide better effect)

Note:
1, Output ends of cable should be adjusted properly before power on, and the arc distance depends on battery voltage and capacity.
2, The arc distance should be from short to , do not produce a est arc at first or the module might be damaged easily.
3, The module has high power and inner heat is not easily dissipated, so it can not work for time.
4, The way to judge if a battery capacity is enough to output maximum power is to measure the battery voltage when producing arc. It the measured voltage is about 6V, then it can output maximum power.

Features:

The module can output high voltage pulse current, small size and high efficiency.
This module is the finished module of transformer for small scientific production.
The input voltage is DC 6V to 12V and will output 1000kV high voltage.
It can be used for negative-ion generator, electronic instrument, and science experiment.
The peripheral circuit is simple, simply connect the switch and battery, and the discharge is great.

Specifications:

Input Voltage: 6V~12V DC
Input Current: 2A~5A (related to voltage)

Output Voltage: About 500KV~1000KV
Input Cable Length: About 100mm(red is positive)

Output Cable Length: About 100mm

Arc Discharge Distance: 10mm~20mm

Instruction:

1. You can use two 3.7V lithium batteries in series, such as 18650 batteries, idle mobile phone batteries (remove the protection board, the recommended capacity is more than 2000mAh) or nickel-cadmium/nickel-metal hydride battery packs, 4V or 6V batteries.
2. This module is a finished module of high-voltage inverter transformer/ for scientific small production. After inputting DC6-12V voltage at the input end, a DC high voltage of about 500,000 volts (about 1-2 cm arc) can be obtained at the output end. ), can be used as a high-voltage source for general experiments, electronic instruments, negative ion generators, and small scientific productions in Chinese subjects.
3. The way to judge whether the battery capacity can drive the maximum output power is to measure the battery voltage during arcing. The maximum power can be output if it is around 6V. Two small-capacity lithium batteries are connected in series to 7.2V, and the measured voltage has dropped to about 4V in the arcing state. The smaller the capacity, the lower the voltage will be. Therefore, it is recommended to use a lithium battery above 2000mA, and it is best to match a battery above 4000mA if possible.

Note:
1, Output ends of cable should be adjusted properly before power on, and the arc distance depends on battery voltage and capacity.
2, The arc distance should be from short to , do not produce a est arc at first or the module might be damaged easily.
3, The module has high power and inner heat is not easily dissipated, so it can not work continuously for time (<10 seconds each time).
4, The way to judge if a battery capacity is enough to output maximum power is to measure the battery voltage when producing arc. It the measured voltage is about 6V, then it can output maximum power. Recommended battery capacity is above 2000mA, or above 4000mA if possible.

Package Includes:

1 x High Voltage Generator

20kV DC3.6-6V 1.5A

Features:

This module is a finished module of transformer/ for small scientific production.

It can output high voltage arc: small size and high efficiency.

The input voltage is DC3.6-6V and will output DC20KV high voltage.

It can be used for high voltage experiment, teaching, and product development.

Two high voltage wires can light up cigarette or paper, single high voltage wire can discharge to any metal quietly.

Specifications:

Input Voltage: DC3.6V-6V

Working Current: 1.5A

Output Voltage: DC20KV

Output Current: 0.05A

Electric Arc Distance: 5mm

Red Wire: Input positive

Green Wire: Input negative

Note:
1, Output ends of cable should be adjusted properly before power on, and the arc distance depends on battery voltage and capacity.
2, The arc distance should be from short to , do not produce a est arc at first or the module might be damaged easily.

Package Includes:

1 x High Voltage Generator

3-11kV DC3.6V/4.8V/6V/12V

Features:

This module is a finished module of high voltage negative-ion generator.

It can output high voltage pulse current, small size and high efficiency.

The input voltage is DC3.6V/4.8V/6V/12V and will output DC3kV-11kV high voltage.

It can be used for fogger, electric salute, gas stove, etc.

The peripheral circuit is simple, simply connect to switch and battery, and the discharge is great.

Specifications:

Input Voltage: 3.6 V, 4.8 V, 6 V, 12 V DC

Output Voltage: 3 kV~11 kV DC

Arc Distance: 10 mm

Working Current: 1000 mA

Input Wire Diameter: 2±0.03 mm

Output Wire Diameter: 6.8±0.03 mm(Live); 2.2±0.03 mm(GND)

Input Wire Length: 200 mm

Output Wire Length: 270 mm(GND); 380 mm(Live)

Input Wire Color: Red(positive), White(negative)

Package Includes:
1 x High Voltage Generator

50-800kV DC4.8V-6V 2A~5A

Features:

This module is a finished module of transformer/ for small scientific production.

It can output high voltage arc, small size and high efficiency.

The input voltage is DC4.8V-6V and will output 50kV-800kV high voltage.

It can be used for high voltage experiment, teaching in high school or college.

The peripheral circuit is simple, simply connect to switch and battery, and the discharge is great.

Specifications:

Input Voltage: DC4.8V~6V

Input Current: 2A~5A (related to input voltage)

Output Voltage: 50V-800kV (related to input voltage)

Electric Arc Distance: <20mm

Wiring:

Battery positive: Red (or Yellow) wire

Battery negative: Green (or White) wire

Note:

1, Output ends of cable should be adjusted properly before power on, and the arc distance depends on battery voltage and current.

2, The arc distance should be from short to , do not produce a est arc at first or the module might be damaged easily.

3, The module has high power and inner heat is not easily dissipated, so it can not work continuously for time (<1 minute each time). Two output wires can NOT connect to each other.

Package Includes:

1 x High Voltage Generator