![]() |
![]() |
![]() |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
![]() |
![]() |
![]() |
System Instructions:
The
solar controller is designed for solar DC power supply system, DC solar
street light system, it has used professional intelligent chip
to control it. It uses one button light touch switch to finish all the manipulation and settings.The controller has many protective functions,
for example, short circuit, over load, wrong connection, over charge, over discharge, auto cut, auto recovery etc. with detailed charging
battery state, load, and breakdown signal LEDs.It can high precisely control of the chip can get battery data such as voltage, discharge current,
environment temperature etc.It uses PWM battery charge mode, to assure the battery at its best state and prolong its life span.
1, The use of single-chip microcomputer and special software, using special software based on expert control system,
realizes the intelligent optimization SOC control.
2, Temperature compensation uses an external temperature sensor, humidity sensor control over the built-in high precision.
3, Overcharge, over discharge, electronic short circuit, overload protection, unique protection against reverse automatic
controller: more protection not damage any parts, do not burn insurance.
4, To use series connection PWM circuit, it is 3%-6% more effective than non-PWM circuit when charging.
To use float charging control mode to prolong the system life span; with high precision temperature compensation function.
5, With LED to show the battery state .
6, To use industrial grade chip (only for with “I” industrial grade controller), it can work under environment such as cold,
high temperature, humid with precise time control.
7, To use Flash memory to keep record of all the working control point, to make the settings digitalized.
9, Built-in super voltage correction procedures to ensure the accuracy of all levels of voltage, charge and discharge
process control correctness.
10, With DC discharge or IHZ strobe flash discharge mode which is especially suitable for street lamp control etc.
11, With constant current output can directly drive LED load can be adjusted with a constant output current load power,
are subject to change conventional LED light source with a constant current source, the installation more convenient, reserved for more space.
12, Using a large-caliber, high interval terminals can be installed
maximum 6mm 2 wire, wire spacing 9.5 mm, enhanced insulation
and installation reliability, not easy to slide wire.
Working Mode Settings:
1, Setting methods:
To press the power switch for 5seconds, the MODE will show LED flashing number, to shop pressing, to press each time, there will be a number,
till the number you needed, and the LED number stop flashing, setting finished. Every time you press it, the LED is No. bright.
2, Only Light control Mode, “0”
When there is no sunshine, the light grade comes down to starting point, the controller will switch on the load in 10 min after have confirmed the signal.
When there is sunshine, the light grade comes up to stopping point, the controller will switch off the load in 10 min after have confirmed the signal.
3, Light control + time delay mode ( “1”–“15”)
Starting process is the same as the above mentioned, when the load works till the fixed time, it will be switched off.
Time setting, please refer the following table. Light control enjoys priority.
4, General Control Mode “16”
This Mode cancel the light control, time control function, output delay and related function, to keep all the other functions,
to take as a common general use controller.
5, Setting ways “17”
To use for system setting, it is the same as the only light control mode, to cancel the 10 min delay function, all the others are the same.
When there is sunshine, the load is switched on, when there is no sunshine, the load is switched off, and it is convenient to check the system
when doing installation and setting.
6, Output Mode Instruction
When the LED shows the setting mode figure, is “1”-“15”, it is only DC output.
Working Mode Setting Table:
(Note: when choosing LED shows decimal mode, the decimal point will be will be
always bright, it doesn’t affect the controller functions, only for differentiation.)
Mode |
LED No. |
Mode |
LED No. |
Setting Methods |
Light control ON +light control OFF |
0 |
Light control ON+ 9Hrs delay OFF |
9 |
To press the power switch for 5seconds,the MODE will show LED flashing number, to shop pressing, to press each time, there will be a number, till the number you needed, and the LED number stop flashing, setting finished. Every time you press it, the LED is No. Bright. |
Light control ON+ 1Hr delay OFF |
1 |
Light control ON+ 10Hrs delay OFF |
10 |
|
Light control ON+ 2Hrs delay OFF |
2 |
Light control ON+ 11Hrs delay OFF |
11 |
|
Light control ON+ 3Hrs delay OFF |
3 |
Light control ON+ 12Hrs delay OFF |
12 |
|
Light control ON+ 4Hrs delay OFF |
4 |
Light control ON+ 13Hrs delay OFF |
13 |
|
Light control ON+ 5Hrs delay OFF |
5 |
Light control ON+ 14Hrs delay OFF |
14 |
|
Light control ON+ 6Hrs delay OFF |
6 |
Light control ON+ 15Hrs delay OFF |
15 |
|
Light control ON+ 7Hrs delay OFF |
7 |
General Use Mode |
16 |
|
Light control ON+ 8Hrs delay OFF |
8 |
Setting Mode |
17 |
Specifications:
Model |
CMT-10A CMTB-10A CMTR-10A |
CMT-20A CMTB-20A CMTR-20A |
Rated Charge Current |
10A |
20A |
Rated Load Current |
10A |
20A |
System Voltage |
12V/24V AUTO |
|
Over load,short circuit protection |
1.25 times by rated current, 60 seconds, 1.5 times by rated current,5 seconds--- overload protection; ≥3 times by rated current--- short circuit protection |
|
No-load loss |
≤6mA |
|
Charge Circuit Voltage Drop |
≤0.26V |
|
Over Voltage Protection |
17V, ×2/24V |
|
Working Temperature |
Industrial Grade: -35℃-+55℃ (Suffix I) |
|
Increase Charge Voltage |
14.6V, ×2/24V (10mins when discharging) |
|
Direct Charge Voltage |
14.4V, ×2/24V (10 mins) |
|
Float Charge Voltage |
13.6V, ×2/24V (till come down to charging recovery voltage) |
|
Charge Recovery Voltage |
13.2V ×2/24V |
|
Temperature Compensation |
-5mv/℃/2V |
|
Under Voltage |
12.0V ×2/24V |
|
Over discharge Voltage |
11.1V ×2/24V |
|
Over Discharge Recovery Voltage |
12.6V, ×2/24V |
|
Control Mode |
PWM |
|
Dimension |
133×70×33.5(mm) |
|
Weight |
140~160(g) |
Package contents:
1 X Solar Charge Streetlight Controller1. We only accept PAYPAL.
2. Payment is to be completed within 14 days of the end of the auction. Please contact us if you can't make the payment promptly. Otherwise, we will reserve the right to relist the item and the unpaid item report will be made correspondingly.
Notes:
Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyer responsibility.
We will NOT be responsible for any delay during delivery including but not limited to customs postage checking, strike, force majeure etc.
As a buyer, it is your duty to pay the tax when you make a order from abroad. Our price does not include taxes, VAT, or other hidden charges.Our working time:
Hong Kong time :Monday to Friday 9:00 am to 5:30 pm.We do not work holidays in China.
if you send email to us,In our working hours will be resumed within 48 hours.
If you we are not satisfied with the product or service ,please contact me and don't give us negative or natural feedback,We must give you a satisfactory solution.
Feedback & DSRs (Detailed Seller Ratings).
We depend on our eBay reputation and customer satisfaction to succeed.Therefore, Your feedback and DSRs are extremely importantto us as better DSR scores affect our search placement on eBay.
We would like to earn your good feedback and 5 star DSR rating. Your action will help us offer our milk and bread . If we have not given you reason enough for 5-star grades on each DSR then please let us know how we can earn your 5-star rating before submitting yourscores!
Contact us through ebay message in English