Product FAQs

Q1: Should I remove the phone case for charging

A1: The charging port has a rubber plug, which allows for charging even during cycling

Q2: Can a phone be used with a stand without a phone case?

A2: The bracket must be used together with the housing. We make them waterproof and designed specifically for outdoor use. This phone case is also suitable for daily use, making you ready to go at any time.

Q3: Is the phone only magnetically connected to the holder?

A3: No magnet. It is a patented metal buckle system. It must be unlocked by pressing a button. If you don't unlock it, you can't take it down. “

Product Features and Function Description

Combination of bicycle bracket and waterproof shell

1、 Waterproof shell

1. Suitable for iPhone phones

2. The product has a simple and round appearance. The front shell material is a combination of hard and soft glue, the outer grip is soft glue, and there are grooves for anti slip design. The rear shell has a frosted effect

3. The protective shell has waterproof, anti drop, and dustproof functions, with a protection level of IP68, which means that the water depth is 1.5m, and the duration of protection is 30 minutes

4. Can accommodate universal mobile phones with or without tempered film, except for tempered film thickness exceeding 0.5mm

2、 Bicycle stand

1. Innovative patented structure, with buckle and clip body for one second hook up and one click pick up of mobile phone

2. The bicycle stand is fixed on the car pole, and the buckle is attached to the phone (phone case). The phone can be easily hooked or removed, making it easy to carry and switch between using the phone

3. The phone buckle structure has two hook directions: horizontal and vertical, which can be selected and switched freely according to needs

4. The bicycle bracket is made of aluminum alloy, which is sturdy and durable

5. Equipped with three sets of soft rubber pads and three common bicycle poles with diameters of 22.2mm, 25.4mm, and 31.8mm, the combination can adapt to poles with diameters ranging from 19-35mm

6. The bracket clamp body can be adjusted 360 degrees horizontally according to different usage habits or needs, and then fixed with the bracket group

7. The connecting buckle is K1 buckle, which has been pasted onto the rear shell for shipment

Installation method and instructions

1、 Waterproof shell assembly

1. Before use, a waterproof test is required: close the front and rear covers of the phone, place the water in the sink, and press a glass water cup at the bottom. After half an hour, confirm that there is no water leakage before installing the phone

2. Tear off the blue film inside the front cover of the phone case

3. Wipe the phone screen clean with a dustproof cloth

4. Tilt the mute button on one side of the phone into the front case (to guide the mute button into the transmission slot) and fully press the phone into the slot

5. Close the rear shell and check if all four edges are securely fastened

6. Open the charging port rubber plug, press the phone screen film flat with your hand, exhaust the air between the film and the screen, and then cover the rubber plug

7. Check the function response of the buttons and the pull button. If the function is normal, the installation is completed. Otherwise, repeat the steps after step 3

2、 Bicycle bracket assembly

1. Select a suitable soft rubber pad based on the diameter of the bicycle pole, and then install the soft rubber pad into the metal bracket

2. Install the metal bracket in a suitable position on the bicycle pole, connect the upper and lower shells of the bracket with the bracket screws, and tighten them with knobs

3. Adjust the buckle body to the appropriate angle of use, and tighten it with flat head screws to connect and fix it with the bicycle bracket

4. Clip the phone into the bicycle clip and lock it through the buckle

5. If necessary, press the blue button to remove the phone

Packaging includes and specifications

1. Front and rear covers of mobile phones

2. Instructions

3. Shell opener

4. Dustproof cloth

5. Lanyard

6. Bicycle stand

7. Bicycle clip

8. Buckle (attached to the rear shell)

9. Soft rubber pad * 3 sets

10. Hexagonal wrench L-shaped

11. Flat head hexagonal socket screw

12. Support screw