Welcome to my store
This item will be shipped from Germany by DHL or UPS to European Union Customers.
Attention:
All goods price include VAT.I will make invoice for every order.
If you have VAT number,don't forget give me your VAT number and company name after payment.
If you don’t have VAT number,you buy it directly,I will make invoice by your ebay address.
Detailed information:
1.Stepper Motor
34HS5435 (34HS5435C-37B2)
Schrittwinkel | Step Angle | 1,8° |
Spannung | Rated Voltage | 5.6 V |
Nennstrom | Rated Current | 3.5 A |
Widerstand | Phase Resistance | 1.6 Ohm/Phase |
Induktanz | Phase inducturance | 20 mH/Phase |
Haltemoment | Holding Torque | 10.5 N.m=1600 oz.in |
Rastmoment | Detent Torque | 24.5 N.cm Max |
Drehmoment | Rotor Torque | 3600 g- cm² |
Leitungen | Lead Wires | 4 |
Achsendurchmesser | Shaft Diameter | 14 mm |
Dual Flat Größe der Achse | Dual flat shaft size | 13mm (1mm for flat) |
Motorlänge | Motor Length | 151 mm |
Gewicht | Motor Weight | 5,0 kg |
Leitungsverbindung | Wires Connection | Red - A+, Green - A-, Yellow - B+, Blue - B- |
2.Driver DM860
Introduction:
Input voltage | 24-80VDC |
Input current | < 6A |
Output current | 2.8A~7.8A |
Consumption | Consumption:80W; Internal Insurance:10A |
Temperature | Working Temperature -10~45℃; Stocking temperature -40℃~70℃ |
Humidity | No condensation, no water droplets |
gas | Prohibition of combustible gases and conductive dust |
weight | 500G |
Pin Function | Details |
PUL +,PUL- | Pulse signal, PUL+ is the positive end of pulses input pin PUL- is the negative end of pulse input pin |
DIR+,DIR- | DIR signal: DIR+ is the positive end of direction input pin DIR- is the negative end of direction input pin |
ENBL+ | Enable signal: ENBL+ is the positive end of direction input pin. This signal is used for enabling/disabling the driver. High level for enabling the driver and low level for disabling the driver. |
ENBL- | ENBL- is the negative end of direction input pin. Usually left unconnected (enabled) |
SW5 | ON | OFF | ON | OFF | ON | OFF | ON | OFF | ON | OFF | ON | OFF | ON | OFF |
SW6 | ON | ON | OFF | OFF | ON | ON | OFF | OFF | ON | ON | OFF | OFF | ON | ON |
SW7 | ON | ON | ON | ON | OFF | OFF | OFF | OFF | ON | ON | ON | ON | OFF | OFF |
SW8 | ON | ON | ON | ON | ON | ON | ON | ON | OFF | OFF | OFF | OFF | OFF | OFF |
PULSE/REV | 400 | 800 | 1600 | 3200 | 6400 | 12800 | 25600 | 51200 | 1000 | 2000 | 5000 | 10000 | 25000 | 50000 |
Output current (A) | ||||
SW1 | SW2 | SW3 | PEAK | RMS |
ON | ON | ON | 2.80 | 2.00 |
OFF | ON | ON | 3.50 | 2.50 |
ON | OFF | ON | 4.20 | 3.00 |
OFF | OFF | ON | 4.90 | 3.50 |
ON | ON | OFF | 5.70 | 4.00 |
OFF | ON | OFF | 6.40 | 4.60 |
ON | OFF | OFF | 7.00 | 5.00 |
OFF | OFF | OFF | 7.80 | 5.60 |
Motor and power pins | 1 | A+ | Motors wiring | |
2 | A- | |||
3 | B+ | |||
4 | B- | |||
5,6 | DC+ DC- | Power supply | Power supply :DC24-80VDC The peak input current can not up to 6A |
Alarm indicator | Reasons | Measures |
LED off turn | Wrong connection for power | Check wiring of power |
Low-voltages for power | Enlarge voltage of power | |
Motor doesn’t run, without holding torque | Wrong connection of stepper motor | Correct its wiring |
RESET signal is effective when offline | Make RESET ineffective | |
Motor doesn’t run, butmaintains holding torque | Without input pulse signal | Adjust PMW & signal level |
Motor runs wrong direction | Wrong wires’ connection | Change connection for any of 2 wires |
Wrong input direction signal | Change direction setting | |
Motor’s holding torque is too small | Too small relative to current setting | Correct rated current setting |
Acceleration is too fast | Reduce the acceleration | |
Motor stalls | Rule out mechanical failure | |
Driver does not match with the motor | Change a suitable driver |
3.Power Supply
Power Supply 350W-60V, input voltage 90~132VAC/180-264VAC, output voltage 60VDC
Power Supply 50W-5V
Output Voltage | 5V |
Output Voltage Tolerance(输出电压容差) | ±5%--±10% |
Rated Output Current(额定输出电流) | 10A |
Output Current Range | 0-10A |
Output Voltage Adjustment Range | ±10% |
Output Power | 50W |
Input Voltage Range | 100-250VAC(selected by switch) |
Input Frequency(输入频率) | 47~63Hz |
Input Current(输入电流) | 10A |
Efficiency(效率) | 72% |
Inrush Current |
|
Leakage Current |
|
Over Load Protection | 110%~150% hiccup mode, auto-recovery |
Working Temperature And Humidity | -10°C~ 60°C, 20%~90%RH |
Weight | 470g |
4.Breakout Board
Description:
• Built in DB25 male connector.
• DB25 Output Pin:P1,P2,P3,P4,P5,P6,P7,P8,P9,P14,P16,P17.
• DB25 Input Pin: P10,P11,P12,P13,P15.
• DB25 GND Pin: P18-P25.
• Power supply: +5V DC.
• Built in C-class Optical-coupler.
• High quality with Surface-mount Tech
P2 P3 is set to X-axis for the X-axis pulse
P4 P5 is set to Y-axis, Y axis pulse
P6 P7 is set to Z-axis Z-axis pulse
The other can be set to A B C axis
A-axis pulse P8 P9 is set as the A axis
P14 is set to B-axis B-axis pulse P1
P16 P17 is set to C-axis, C axis pulse
Can also be set to the spindle control signal \ electrical permit
Input interface for the P10 P11 P12 P13 P15
Additional instructions:
1.About VAT invoice:Usually I will make invoice every Friday.
Now ebay doesn't show e-mail.If you want invoice,you give me your e-mail,I can send invoice to your e-mail
2.Delivery time:All products are available and can be shipped out right after payment.
I only make ship on work day(Except Saturday、Sunday and Holiday).
- Shipping via DHL or GLS.
After delivery,for Germany,about 2~3 work days.
After delivery,for EU country,usually about 5~7 work days, if you not receive goods at the Eighth work day,you search the tracking on DHL or GLS website.If the tracking has problem,you make a call to your local DHL or GLS,then contact me .
3.Service: If you need more pictures, descriptions, manual, please contact me.
If you have problem,when you connect it,you contact me,I will help you.
Application:Our Stepper Motors are used on small to mid-sized CNC mills or milling machines, CNC lathes, Pick-n-place machines,Laser Engravers and Laser Cutters, Vinyl Sign Cutters, CNC Plasma Cutters, and CNC Foam Cutters. Carver machine ,Dispenser,Automazation,3D Printer,Stage lighting,instrument,laser equipment,scanner Dispenser,Logistics equipment,and so on.These motors have been used in precision telescope positioning systems and robots.