eBay

You are bidding on a 48 Volt 100% DIGITAL battery controller to prevent over-charging by simple dumping or cutting of incoming power. With EZ 5-point connection bar.

Long Service Life Digital Model
Come with mounting flanges on both components
Our most versatile model is this 48 volt system that can be micro programmed
by the operator to keep a 48 volt lead acid, gel, AGM, Li-ion, EB, etc.
Fine tune to your needs with the simple programming buttons.
(See video's - cut and paste the URL's into any web browser bar)
: CLICK HERE TO SEE 48V / 1000 Watt DUMP LOAD

https://youtu.be/81y50tpSads https://youtu.be/rVffRzl6zcY https://www.youtube.com/watch?v=f9_P2rfQzgs https://www.youtube.com/watch?v=f9_P2rfQzgs https://www.youtube.com/watch?v=IZRahrogJ_A https://www.youtube.com/watch?v=NZENiUNoHWo

SEE a Great Video on how to use it below

HOW TO PROGRAM IT CLICK HERE

WIND/SOLAR 48 VOLT 200 AMP DUMP / DISCONNECT CHARGE CONTROLLER

WITH BUILT IN DIGITAL DISPLAY AND INTELLIGENT DUAL PROCESSOR CONTROLLER

(With Original "THEM" Thermodyne Controller. Says THER on the board. Made with real high voltage rated parts.

Some people claim Thermodyne made but only boards stamped "THER" are genuine Thermodyne boards)

For solar panels and solar

IT CAN DISCONNECT THE INCOMING POWER

OR DIVERT IT TO A DUMP LOAD.

Max solar amperage in divert (dump) mode is 200 amps. This is a big hybrid wind and solar charge controller.
Use for wind or solar or both at the same time! Also use for hydroelectric or solar or both.
User changeable settings -- Several controllers on the market only let you set the dump level!
Connect multiple turbines and solar panels up to 200 amps worth at the same time!
Max continuous solar amperage in disconnect mode is 100 amps. REBUILT WITH NEW WIRING.

    Can divert the charging source from the batteries to the load, or dump both the batteries along with the charging source.
    You can connect both wind and solar at the same time. Reverse polarity protection
    Ultra low power consumption even with the volt meter on (almost negligible). You can even set the volt meter to turn off after in-activity.

On board relay- Isolates electronics from back voltage spikes from large 440 amp relay.

This is important to get the longest life out of the electronics. No body else has this!

Dual (2) Microprocessor controlled -- Extremely stable and very accurate

Multiple user changeable settings, and trip points for many various system requirements and applications- You can change the dump point voltage level,

end of dump voltage level, length of time in divert mode when end dump point voltage is reached

Isolated Electronics Protection - Impossible to accidentally connect wind or solar directly to the circuit board.

High amp rating - 200 amps, 10,000 watts surge peak max.

Battery Status digital LED - Lets you know your battery's actual voltage in real time!

Green LED come on and then you know it's in dump mode or cut mode depending on how your relay lugs wired.

Battery regulator for both your wind and solar battery input power. This
regulator can either dump extra power creating free hot water or heat or
just cut off extra power to keep your batteries from over charging. This
unit is a must for wind turbine applications as it uses a mechanical
relay which can handle high voltage surges unlike solid state controllers.

This item is the only controller that will work with wind turbines Do not buy solid state controllers as they will burn out in high wind conditions. This controller was specially developed for wind turbines. Also works on solar too - Get one battery controller to do it all!
Worlds Lowest Cost 200 AMP
Wind & Solar Controller

Battery Regulator-
Cut/Disconnect Controller-
Diversion Load Regulation-

This High Amp unit can control battery banks

Used to prevent battery over
charging on Wind - Solar - Hydro

A battery regulator diverts excess power to power
some other useful device when ever your battery is full.

Use the this excess power to make free hot water or
to recharge an auxiliary battery bank, so many uses!

An extremely robust unit!
draws almost ZERO power while sensing! 99.998% electrically efficient while sensing!

100% MOSFETS - Built to take over 2 Billion cycles or about 85 years of switching for the average system.

Battery regulator.
Charge regulator.
Charge controller.
Dump load regulator.
"Cut" charge controller.
Diversion load regulator.
Micro processor controlled.
Versatile raised steel mounting plate.
Measures 10" long by 7" wide by 3" tall.
Works for all Wind Turbines, Solar panels and Hydro.
For all voltages ranges in multiple battery banks.
No grounded IGBT's or MOSFETS - Lighting strike proof isolation.
CUT -LOAD controller (No need to buy a dump load resistor)
Electrically efficient. Draws only trace power while sensing!
Does not waste electricity while sensing in diversion load mode!

HOW POWER DRAW DYNAMICS WORKS:
If you use it as a DIVERSION or DUMP load MODE then it uses no power when it is NOT dumping (energy efficient sensing)

The modern way to monitor your battery from over charging is to have a diversion load that performs another task such as heating water when your battery is in danger of over charging. Shutting down the output of your wind turbine or your other renewable energy devices is old school thinking. Now-a-days most people dump their excess power into some other legitimate device optimizing their energy independence. Hot water from your excess power can be used for radiant heating in the winter or even in the hot summer months for washing cloths or dishes and for bathing. You will always find a need for hot water in your life.


"Simple and ultra-reliable" - "A BULLET PROOF SYSTEM"