Kit Includes
- APC Proteous 500 Italian Made FEATURE RICH Sliding Gate Motor With Two Remotes (QTY: 1)
- APC Four Button Keyring Remote (QTY: 3)
- 115mm High Bolt Down Galvanized Gate Stop (QTY: 1)
- 520mm Nylon Rack (QTY: 10)
- Gate Sensor | APC Photoelectric Gate Safety Sensor - Safety Beam Infrared Photocell Gate Sensor Detector (QTY: 1)
- 10m 4 Core Non Shielded Cable (QTY: 1)
- APC Wired Double Push Button Switch with Key Issolation (QTY: 1)
- 5m 4 Core Non Shielded Cable (QTY: 2)
- APC Mondo Wi-Fi Keypad with APP Control and Swipe Tag Reader (QTY: 1)
- Em Swipe Tag (QTY: 2)
Product Information
Heavy Duty Feature Rich 24V Italian Sliding Gate Motor Overview
At a glance
The Proteous 500 boasts a cutting edge and rich feature set of full programmability using the onboard intuitive LCD interface suitable for the novice user with simple setups all the way to 100% commercial sites with its advance features and its high duty cycle system There is no function or feature that this system cannot perform. See the full details below.
System Features
Capacity
90% Duty Cycle (Can operate for up to 54 Minutes of every 60 minutes) Full Feature MODERN Programmability by LCD Display (No DIP Switches or Dials) 500KG Capacity (1/2 a Tonne) Ultra long 10 metre gate capacity Only 150mm Narrow Depth
Everything and more as standard..
Automatic learning of gate travel limits and automatic introduction of soft start and soft stop points Configurable pedestrian operation travel amount which can be operated by remote, keypad, button, APP control (module available) and induction loop Fast and Slow Speeds are adjustable Simple ONE PRESS full feature remote Ultra High Security Rolling Code learning system (and service free remote learning options) Ultimate Auto close settings adjustable from 5 seconds to 20 Minutes Party Mode System to keep gates opened when configured for use with the automatic close feature Underside cable entry with grommets Simple to setup left and right side magnet system Pre-Wired and ready to plug into a regular 10A power point or can be hardwired if preferred All installation connections are low voltage (except in the case of high voltage driveway lights(low voltage can be used)) Strong STEEL Pinion Gear Solid Alloy Housing with FOUR POINT tilt leveling adjustment system (30mm in any or all direction)
Special Features
Energy Saving Mode (5mA Standby Current) Optional battery backup system Standalone low voltage/high voltage driveway light control by remote (completely separate to the safety light) Soft Start/Soft Stop (Ramping feature) with adjustable cut in points Supports Bi-Parting Sliding Gates using only one set of accessories using the APC SYNCRO module system Induction Loop Compatible for auto opening or as a safety device Supports programmable timers
Safety Features
Adjustable Over current adjustments Built in Encoder with adjustable sensitivity Safety Sensor connection input configurable for open and/or closing Supports Safety Edges Automatic Courtesy Light Output (Blinking or Static illumination) with adjustable pre-operating courtesy times
Simple to use LCD interface
Control Board Overview
Accessories Compatibility and Controlling Options
Constant DC Accessories Output Open/Stop/Close Inputs for Full Gate Operation and Pedestrian Gate Operation Remote controls Induction Loops Weekly Timers Entry and Exit push button with isolation key switches (Wired and Wireless Options Available) Keypads (Wired and Wireless Options Available) Exit/entry sensors Intercom system with dry contact output Automatic switching timer WiFi Control System (App Based Control) GSM Control Systems (Mobile Call/SMS based Control)
Remote Features
Dimensions
Installation Options
Concrete in Base Plate
Four point Tilt Leveling
Specifications
| Transformer | 24V AC |
| Rectification | In Housing Rectifier |
| Motor Output Voltage | 24v DC |
| Max Operating Power | 300 Watts |
| Maximum Gate Length | 10 Metres |
| Maximum Gate Weight | 500 KG |
| Speed | 28 cm/s |
| Working temperature | -20° - 50° |
| RF | APC Rolling code 433.92mhz |
| Motor Duty Cycle | 90% |
| Auxiliary Inputs | 0V Momentary Pulse |
| Accessories Voltage | 34V DC |
| Operator Inbuilt Safety | Over current + Encoder Sensitivity |
Optional Battery Back Up
An optional battery backup system is available for the automation kit. The back up battery system will allow for continued use of the gate system and will automatically recharge upon power restoration. Whilst the system is powered it will continue to float charge to keep the batteries topped up ready for use. The systems is supplied with the charger module along with the 1.3aH battery pack and is installed within the empty compartment of the proteous system.
Compartment with Battery Pack and Charger Installed
Which Proteous Sliding Gate Motor is best for my requirments
APC-PE2000 Photoelectric Safety Sensor Set
If the gate begins to close and the sensor path is interrupted then the gate will stop and return to the open position.
Both sensors (transmitter and receiver) are wired back to the control box of the gate system using the supplied cable roll, alternatively a reflective sensor upgrade is available which will only require wiring from the sensor mounted at the control box.
- Up to 15 Metres Infared beam operating distance
- Only powers on when the command is given to close the gates
- Alignment led to assist in the installation process
- Weather sealed with the supplied cover seals
- Easy screw down wiring termination
APC Mondo Wired Keypad with APP via Wi-Fi
The APC Mondo Wi-Fi Keypad can be used as a simple keypad access control device or alternatively as an advanced unit. Its special features allow the system to be operated by Pin Code, Swipe Tag and even remotley by APP whether on-site or off-site (anywhere in the world).
Supplied with a 10 meter cable roll it is wired back to the main control board of the system. Its also supplied with two swipe tags for PIN FREE access.
Key Feature Set:
- Full operational control by Tuya APP
- Resin Filled for best weatherproofing
- Low Power Consumption
- Backlit Touch Keys
- Up to 2000 Users
- Pin Code, Swipe Tag or DUAL AUTHENTICATION Swipe Tag then Pin Code
- Adjustable Relay Time from 0-99s or Latching ON/OFF
- Doorbell Contacts to connect to your doorbell system
Wired Double Push Button with Isolation Key
The wired double push button switch is a simple and easy to use method to operate the gate for full gate operation and also pedestrian function.
It is mounted in the general area of the gate and can be isolated by using the supplied keys without affecting the rest of the system, this is handy if you want to continue using the remotes or any other method of operation but wish to stop use of the push button itself.
The push button is wired to the control board using the supplied cable roll. If required the button can be upgraded to a wired keypad for higher access security using pin number for either the full gate operation or pedestrian function.